3 in 1 Grass Trimmer/Edger Coupe gazon/Taille-bordure 3 en 1 3 en 1 Cortadora de cesped/Ribeteadora HElPliNE NumBER 1-866-354-woRx (9679) EN P06 F P15 ES P25 WG160 WG160.
7 9 10 8 1 2 11 15 3 14 12 4 13 6 5
b a A B1 B2 9 B3 C D 15 14 E F1 F2 11 16 G H1 H2 10
H3 I1 I2 17 J1 J2 K1 K3 L1 18 19 20 22 K2 21 RIGHT L2 L3 L4 WRONG
1. Rear Handle 2. Battery Pack 3. Telescopic Shaft 4. Pivot Head Locking Knob 5. Safety Guard 6. Flower Guard/Edger Guide 7. Auxiliary Handle 8. Telescopic Shaft Adjustment Trigger 9. Lock Off Button 10. On/Off Switch 11. Auxiliary Handle Locking Lever 12. Edger/Trimming Support Wheels 13. Line Cutter 14. Lower Shaft Coupling 15. Upper Shaft 16. Motor Housing of Trimmer Head 6 17. Line Feed Button (See Fig. K1) 18 Spool Cap Cover (See Fig. K2) 19 Cap Release Latch (See Fig. K2) 20. Spool (See Fig.
TECHNICAL DATA WG160 WG160.1 Voltage 20V WG175 Max* No load speed 32V 7600/min Cutting diameter 12” Line diameter 0.065” Charging time 3hr approx. Machine weight Max** 5.7lbs 6.2lbs * Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts. ** Voltage measured without workload. Initial battery voltage reaches maximum of 32 volts. Nominal voltage is 28.8 volts. Accessories WG160 WG160.
SAFETY INSTRUCTIONS WARNING! Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks and cement and other masonry products, and • Arsenic and chromium from chemicallytreated lumber.
2) Do not use battery-operated appliance in rain. 3) When replacing batteries, all batteries should be replaced at the same time. Mixing fresh and discharged batteries could increase internal cell pressure and rupture the discharge battery (ies). (Applies to products employing more than one separately replaceable primary battery.) 4) When inserting batteries into this product, the proper polarity or direction must be observed. Reverse insertion of batteries can result in leakage or explosion.
SYMBOLS ASSEMBLY Warning Read the manual Do not expose to rain or water Do not burn 40-105ºF Always charge the battery pack between temperatures 40°F (4.5°C)-105°F (40.5.°C). Do not dispose of batteries, return exhausted batteries to your local collection or recycling point 10 BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING To preserve natural resources, please recycle or dispose of batteries properly. This product contains lithium-ion batteries.
permit charging. Allow time for the battery to cool down before recharging. 3. TO REMOVE OR INSTALL BATTERY PACK (See Fig. C) Depress the battery release button to remove Battery Pack (2) from your trimmer. After recharging, insert the Battery Pack onto trimmer’s battery bracket. A simple push and slight pressure will be sufficient. 4. SAFETY ON/OFF SWITCH (See Fig. D) The safety switch is locked off to prevent accidental starting.
EDGER/TRIMMING SUPPORT WHEELS There are three optional positions for the Edger/Trimming Support Wheels to attach when assisting in Trimming and Edging. Position 1: Using the guide wheels when trimming in a forward or reverse direction (See Fig. J1) Position the Grass Trimmer in the trimming position. Underneath the Safety Guard there is a metal plate that the Edger/Trimming Support Wheels will attach to.
Cutting Head (21). Keep the Spool Cap Cover and the inside of the Cutting Head clean from debris. To replace the Spool Cap Cover, press it firmly onto the Spool Holder. Ensure that it is correctly connected by trying to remove it without depressing the two Cap Release Latches. user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry room temperature location.
Troubleshooting The following table gives problems and actions that you can perform if your machine does not operate correctly. If these do not identify and correct the problem, contact your WORX Customer Service at 1-866-354-WORX. Warning: Switch the machine off and remove the battery prior to any troubleshooting. Problems Possible Causes Corrective Action Trimmer fails to operate. Battery discharged. Battery too hot/cold. Motor is broken. Internal wiring of machine damaged.
