Instruction manual

ManualsBrandsWorx ManualsLawn MowerWG259E.5

WG259E

WG259E.5 WG259E.9

SAFETY AND OPERATING MANUAL

Cordless Hedge Trimmer

Summary of content (12 pages)

PAGE 1
SAFETY AND OPERATING MANUAL Cordless Hedge Trimmer WG259E WG259E.5 WG259E.
PAGE 2
General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 2 1. Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
PAGE 3
dust collection can reduce dust-related hazards. 4. Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
PAGE 4
gripping surfaces only, because the cutter blade may contact hidden wiring. Cutter blades contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Safety Warnings for battery pack 4 a) Do not dismantle, open or shred cells or battery pack. b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-circuit each other or be shortcircuited by conductive materials.
PAGE 5
SYMBOLS To reduce the risk of injury, user must read instruction manual Wear ear protection Wear eye protection Wear dust mask Do not expose to moisture. Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem. Do not dispose of waste batteries as unsorted municipal waste.
PAGE 6
2 3 5 6 4 8 7 1 6 9 Cordless Hedge Trimmer WG259E WG259E.5 WG259E.
PAGE 7
1. Battery Pack 2. Rear Handle 3. Front Handle 4. Safety Guard 5. Front Switch Lever (All Around Switch Function) 6. Rear Switch Lever 7. Battery Pack Release Button 8. Blade 9. Blade Sheath* * Not all the accessories illustrated or described are included in standard delivery. TECHNICAL DATA Type WG259E WG259E.5 WG259E.9(230-269- designation of machinery, representative of cordless hedge trimmer) WG259E Voltage WG259E.5 20V No load speed 2200/min 52cm Max.
PAGE 8
WARNING: The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used dependant on the following examples and other variations on how the tool is used: How the tool is used and the materials being cut or drilled. The tool being in good condition and well maintained The use the correct accessory for the tool and ensuring it is sharp and in good condition.
PAGE 9
OPERATING INSTRUCTIONS WARNING! Do not use the product without attaching the guard and front handle. Intended Use The machine is intended for cutting and trimming hedges and bushes in domestic use. 1. GUARD ASSEMBLY Insert the Safety Guard (4) into the slot as illustrated in Fig A; making sure it is securely attached. Use two screws to fix the Safety Guard securely. 2. FRONT HANDLE ASSEMBLY The Front Handle (3) must be assembled before use: 1) Remove the bolt from the Front Handle.
PAGE 10
5. TO REMOVE OR INSTALL BATTERY PACK (See Fig. E) Depress the Battery Pack Release Button (7) to release battery pack from your tool. After recharging, insert the battery pack into the battery port. A simple push and slight pressure will be sufficient. Check to see if the battery is fully secured. E 10 F1 F2 6. STARTING AND STOPPING BEFORE STARTING YOUR HEDGE TRIMMER Remove Blade Sheath (9). TO START YOUR HEDGE TRIMMER Your hedge trimmer is equipped with two Switch Levers (5 & 6).
PAGE 11
TOP CUTTING Use a wide sweeping motion (See Fig. G1). A slight downward tilt of the cutting blades in the direction of motion gives the best cutting results. SIDE CUTTING When trimming the sides of the hedge, begin at the bottom and cut upwards (See Fig. G2), tapering the hedge inward at the top. This shape will expose more of the hedge, resulting in a more uniformed growth. 8. CLEANING REMOVE THE BATTERY PACK. Use a soft brush to remove debris from all air intakes and cutting blade.