Owner’s Manual EN P02
ORIGINAL INSTRUCTIONS TABLE OF CONTENTS 2 1. Product Safety 1.1 General & Additional Safety Instruction 1.2 Information on the Landroid® 3 2. Component list 6 3. Technical data and noise data 3.1 Technical data 3.2 Noise data 8 4. Control Panel 10 5. Understanding Your Landroid® 5.1 How does my Landroid® know what to mow? 5.2 How does my Landroid® know where to go? A. Finding the charging base B. Rain sensors C. Sensing the boundary wire D. Starting and stopping while mowing 5.3 Cut to Edge 5.
1. Product Safety 1.1 General & Additional Safety Instruction WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Carefully read the instructions for the safe operation of the machine. Save all warnings and instructions for future reference.
or a) b) c) d) e) f) g) replacing the blades. Keep all nuts, bolts and screws tight to be sure the appliance is in safe working condition. Inspect the robotic lawnmower each week and replace worn or damaged parts for safety. Check especially that the blades and blade disc are not damaged. Replace all blades and screws at the same time if necessary so that the rotating parts are balanced. Ensure that only replacement cutting means of the right type are used.
1.2 Information on the Landroid® WARNING - Robotic lawnmower can be dangerous if incorrectly used. Read through the Operator’s manual carefully and understand the content before using your robotic lawnmower. WARNING - Keep a safe distance from the machine when operating. WARNING – Operate the disabling device before working on or lifting the machine. WARNING - Do not ride on the machine. Do not burn Do not expose to rain or water. 5 Do not dispose of batteries.
2.
1. STOP BUTTON 2. REAR DRIVING WHEEL 3. BATTERY PACK 4. DISPLAY 5. HOME BUTTON 6. START KEY 7. ON/OFF KEY 8. USB PORT 9. RAIN SENSOR 10. CHARGING STRIPS 11. CUTTING HEIGHT ADJUSTMENT KNOB 12. FRONT WHEEL 13. BLADE TURNING DISC 14. CUTTING BLADE 15. CONTACT PINS 16. CHARGING BASE 17. POWER ADAPTER 18. WIRE PEGS 19. BOUNDARY WIRE 20. CHARGING BASE FIXING NAILS 7 21. BOUNDARY WIRE DISTANCE GAUGE 22. HEX KEY 23. CONNECTOR 24.
3. Technical data and noise data 3.1 Technical data Type WR130E WR131E WR141E WR144E (100-199 - designation of machinery, representative of Robotic Lawnmower) WR130E WR131E WR141E WR144E Rated voltage 20V No load speed Max.* 2800/min 300m2 Cutting area 500m2 Cutting diameter 18cm Cutting height 20-50mm 30-60mm Cutting height positions 4 Battery type Lithium-ion Battery model WA3551.3 Charging time approx. 8 4hrs 1.5hrs Charger model WA3766 WA3750.1 / WA3755.
Boundary wire distance gauge 2 2 Blade 9 9 Connector 2 2 Battery pack (WA3551.3) 1 1 Charger (WA3766) 1 / Charger (WA3750.1 / WA3755.1) / 1 We recommend that you purchase genuine accessories listed in the above list from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. Your Landroid® can be used with other WORX functional accessories. Visit www.worx.
4. Control panel LOCK Wi-Fi BATTERY CAPACITY WORKING TIME DISPLAY Displays the state of your setting START Starts mowing/ Selects up POWER ON/OFF Turns Landroid® on and off OK Confirms any setting/ Enters Wi-Fi connection mode HOME Sends Landroid® to its charging base during operation and activates charging/Selects down STOP Stops Landroid® during operation 10 STANDBY PAGE: Landroid® is not in the working hours. SLEEP PAGE: Landroid® is fully charged and is not in the working hours.
5. Understanding Your Landroid® Congratulations on your new purchase of Landroid® and welcome to the care-free life of automatic mowing. In the g we want to help p yyou to better understand how yyour Landroid® thinks. following, 5.1 How does my Landroid® know what to mow? Landroid® chooses its direction at random. It will make sure your entire lawn is evenly mowed without leaving unattractive mowing paths (See Fig. A).
5.2 How does my Landroid® know where to go? Your Landroid® is made to work on its own. Landroid® knows when it needs to go to its charging base to charge, can sense when it is raining, can stop itself if it senses a problem, and knows to stop, draw back, and turn around when it bumps into something blocking its path. Landroid® will also automatically stop its blade turning disc from rotating if it is lifted off the ground to prevent an accident. A.
Only for reference E1 Only for reference E2 5.3 Cut to edge (only for WR141E WR144E) Off-centered blade turning disc design provides a clean cut with narrowest distance to the boundary or wall. It helps minimize the amount and frequency of manual trimming along the boundary. Additionally, Landroid® is designed with a protective cover underneath that prevents objects from touching the turning blades and/or injury. (See Fig. F) “Cut to Edge” Tech 5.
to to select the number and press to confirm. Then will be blinking, use the same method to select the number and press to confirm. Now the time setting is completed and Landroid® will enter the standby page. 4hrs Only for reference Only for reference Standby page Only for reference 14 (3)Set work area Keep pressing for 3 seconds. When the icon is blinking, press . A number will be blinking on the display, for example, , which is the lawn area.
5.5 How efficiently will my Landroid® mow the grass? Mowing times are different for every lawn depending on the factors mentioned below. Gradually adjust the time you allow Landroid® to mow each day until you find the most suitable setting.
3. Make sure your router channel/ band width of wireless setting is Auto or 20M or 20M mixed 40M. (See Fig. 1) 4. Make sure your router Enable the SSID Broadcast function when you connect the machine with the APP. And you can close it after you connect successfully. (See Fig. 1) Fig. 1 5. Make sure DHCP function is enabled. (See Fig. 2) Fig. 2 16 6. If you have a “Fritz!box” Router, please make sure activate “Allow communication between devices in same network” in the settings. 7.
Step 3: Enter the Landroid® APP, and then follow the instructions to connect to your Wi-Fi. *The Serial No. can be found at the rear of Landroid® as shown (See Fig. H) . H NOTE: 1. If your Wi-Fi information changes, Landroid® needs to be re-set according to Step 3. 2. When Landroid® is located in an area with low or no Wi-Fi signal, instructions sent from the mobile App may not be executed immediately. Landroid® will receive instructions when it returns to an area with good Wi-Fi signal. 3.
7.2 Burying the Boundary Wire If you are planning to bury the boundary wire, it is recommended to first peg it down. This allows you to easily change the layout if necessary before burying the wire. When the boundary wire installation is complete, have Landroid® follow and check the path by pressing and . This allows your Landroid® to adjust to its new environment. .
(2) Place Landroid® on a secure and level surface. Press to turn off your Landroid®. (3) Insert the USB drive (flash drive) in the port. (See Fig. K1) (4) Turn Landroid® on. The update will begin automatically. Wait until the display shows “ ” (See Fig. K2), then remove the USB drive (flash drive) and tightly close the protective cover. When the display shows “ ”, the update is complete and Landroid® will enter the PIN page. Method 2: Update via your smartphone.
make forward and reverse rotation at random to use both cutting edges and minimize the frequency of replacing the blades. Each cutting blade will last up to 2 months when it is programmed to mow everyday. Always check to see if the blades are chipped or damaged and replace them if they are. When the cutting blades are dull and worn out, they should be replaced with the spare blades provided with your Landroid®. Spare blades are also available at your nearest WORX retailer. 1 2 L A.
O1 O2 C. Clean the contact pins and the charging strips Clean the contact pins located on the charging base and the charging strips located on Landroid® using a cloth. Remove any built up grass clippings or debris around the contact pins and charge strips periodically to ensure Landroid® successfully charges each time. 9.3 Battery life The heart of Landroid® is its 20V Li-Ion battery. For proper storage of the battery, make sure it is fully charged and kept in a cool dry place.
9.5 Replacing the battery WARNING: Power off before attempting any adjustment, replacement or repair. Open the battery pack protection cover. Press down the battery pack release button to remove the battery pack from Landroid® . (See Fig. Q) Insert a new and fully charged battery pack into the battery port. A simple push and slight pressure will be sufficient until a click is heard. Check to see if the battery is fully secured. Q 10. Function Messages Display Message Action Rain delay activated.
Landroid® is trapped. 1. Turn Landroid® off; 2. Take Landroid® to an area in your lawn free of obstacles obstacles. 3. Turn Landroid® on. Press then . 4. If the error message is still displayed; turn power off; turn Landroid® upside-down. Check if there is anything preventing the wheels from rotating. 5. Remove any obstruction, turn Landroid® upright, turn power on. Press then . Landroid® is lifted up. 1. Turn Landroid® off. 2. Take Landroid® to a lawn area clear of obstacles, turn Landroid® on.
13. Troubleshooting If your Landroid® does not work correctly, follow the troubleshooting guide below. If the issue persists, contact your Dealer. Symptom Cause Action The LED light on the charging base does not turn on. There is no power. Check the charging base is connected properly to the power adapter and the power adapter is connected to a suitable power supply. Red light turns on the charging base. The boundary wire isn’t connected or boundary wire is broken.
Landroid® is starting to have shorter run-times between charges. Something is clogging in the blade disc. Take off the blade disc and clean it. The grass is too high and too thick. Check the Blade Disc and blades, remove debris and foreign objects from the blades and Blade Disc. Landroid® is shaking heavily. Check the blade disc and blades, remove debris and foreign objects from the blades and blade disc. The clock is not set to the correct time.
Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Declaration of Conformity We, Positec Germany GmbH Grüner Weg 10, 50825 Cologne, Germany Declare that the product, Description Robotic Lawnmower Type WR130E WR131E WR141E WR144E (100-199- designation of machinery, representative of Robotic Lawnmower) (Year, article number and month of serial number are placed on the back page. The complete serial number is clearly stated on the enclosure of lawnmower) with battery charger WA3766 / WA3750.1 / WA3755.1 and charging base WA0510 / WA4002.
Copyright © 2018, Positec. All Rights Reserved.
