SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Rotary Hammer WU334L
General power tool safety warnings c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Additional safety rules for hammer 1 Symbols To reduce the risk of injury, user must read instruction manual Always wear a dust mask. Warning Wear eye protection Wear dust mask Wear ear protection Double insulated Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Component list 1 Quick Change SDS-Plus Chuck 2 Depth Gauge 3 Function Mode Selection Switch 4 Grease Box Cover 1 5 Anti-Vibration Handle 2 3 4 5 6 On / Off Switch 7 Thumbwheel Switch For Speed Preselection/Impact Frequency Preselection 8 Auxiliary Handle 6 7 8 Not all the accessories illustrated or described are included in standard delivery.
Technical data Vibration information Type WU334L (330~359-designation of machinery, representative of Rotary Hammer Drill) • Voltage 110V~50Hz • Power input 900W • No load speed • Hammer drilling into concrete 0-720/min • Impact rate Vibration emission value ah,HD=15.3m/s2 Uncertainty K=1.5m/s2 0-3500/min • Impact energy • Chuck type Vibration total values (triax vector sum) determined according to EN 60745: 5.5J • Quick Change SDS-plus Chiselling Vibration emission value ah,Cheq=12.
Warning: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period. Helping to minimise your vibration exposure risk. ALWAYS use sharp chisels, drills.
Operating instructions note: Before using the tool, read the instruction book carefully. Intended Use The machine is intended for hammer drilling in concrete, brick and stone as well as for light chiseling work. It is also suitable for drilling without impact in wood, metal, ceramic and plastic. Warning! Before any work on the machine itself, pull the mains plug. 1 INSERTING AND REMOVING DRILL BITS IN THE QUICK CHANGE SDS-plus CHUCK Take care that the dust protection cap is not damaged when changing tools.
2 ATTACHING AND REMOVING THE CHUCK Note: Ensure the Function Mode Selection Switch (3) is not in the chisel rotation mode( ) or the chuck cannot be removed. Chuck icons: “ “unlock “ “lock 1) REMOVING THE CHUCK (See Fig. B1) Firmly turn the Rotary Sheath(b) as far as possible in the direction noted by the unlock Icon“ “(clockwise) then pull the chuck(1) off. After removing, clean the chuck and spindle of any debris fragments and apply lubrication to the chuck for protection. 2) ATTACHING THE CHUCK (See Fig.
5 USING THE DEPTH GAUGE (See Fig. C) The Depth Gauge(2) can be used to set a constant depth to the drill. Fit the drill bit into the chuck. Loosen the depth gauge by rotating the locking screw (c) anti-clockwise. Slide the depth gauge until the distance between the depth gauge end and the drill bit end is equal to the depth of hole/screw you wish to make. Then clamp the depth gauge by rotating the locking screw (c) clockwise. 6 ON/OFF SWITCH WITH VARIABLE SPEED CONTROL (See Fig.
For drilling into steel, wood and plastics choose the Rotary drilling position. For simultaneous drilling and impacting of concrete or masonry, choose the Hammer drilling position. Chisel rotation position for adjustment of the chiselling position.(Non-work position) For impacting only - for light chipping, chiseling and demolition applications choose the Hammer position. Warning! The operating mode selector switch may be actuated only at a standstill.
9 LUBRICATION MACHINE (See Fig. F) The machine is grease-lubricated. A grease refill is only required during hammer work efficiency is low. Open the grease box lid at the top of the hammer using the pin spanner. Then refill approx 30g grease. Caution: Keep the container of grease away from children. e 10 REPLACE THE BRUSHES (See Fig. G1,G2,G3) When the resin insulating tip (g) inside the carbon brush (h) is exposed to contact the commutator (f) , it will automatically shut off the motor.
1 2 3 4 5 Working hints for your tool Trouble shooting Reduce the pressure on the drill bit when it is about to break through. This will prevent the drill from jamming. When drilling a large hole, first drill a pilot hole using a smaller drill bit. Always apply pressure to your drill bit in a straight line, and if possible at right angles to the workpiece. Never change the operating mode whilst the drill is running. Do not apply excessive pressure to the tool when chiseling.
Environmental protection Plug replacement (UK & Ireland only) Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice. If you need to replace the fitted plug then follow the instructions below.
EC DECLARATION OF CONFORMITY We, Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX Rotary hammer Type WU334L (330~359-designation of machinery, representative of Rotary Hammer Drill) Function Hammering various materials Complies with the following directives, • Machinery Directive • Electromagnetic Compatibility Directive • RoHS Directive 2006/42/EC 2004/108/EC 2011/65/EU Standards conform to EN 55014-1 EN 55014-2 EN 61000-3-2 EN 61000-3-3 E
Copyright © 2012, Positec. All Rights Reserved.
