Front Drive Elliptical Model No: E750 BODY WORX Retain this owner’s manual for future reference Read and follow all instructions in this owner’s manual Version A 1
Safety Instructions • To ensure the best safety of the exerciser, regularly check on damage and worn parts. suitable, non-slip mat under the exerciser. • If you pass on this exerciser to another person or if you allow another person to use it, make sure that that person is familiar with the content and instructions in these instructions. • The general rush is that exercisers and training devices are not toys. Therefore, they must only be used by properly informed or instructed persons.
Exploded drawing: 55 53 52R 101 13 64 60 40 63 9B 7 6 65 54 63 67 103 15 68 107 23R 111 75 105 71 95 106 86 87 48 34 23L 12R 10 41 8 7 9B 69 72 41 60 40 42 72 32R 107 52L 107 73 21 72 74A 74B 63 84 49 102 84 17 14 41 77 80R 8 7 9B 63 93R 93L 41 8 7 9 6 7 9 43 82 24 26 1 12L 35 51 97 45 16 83 46 70 56 50 37 100 95 47 89 45 86 18 94 44 76 80L 57 88 61 19 9A 7 6 22 4 9B 7 8 3 96 6 7 9C 32L 102 84 31 72 33 11R 66 38 9B 7 6 104R 104L 63 39 79 5R 81 8 7 20
Checking list: 10 12R&L 1 49 X1 64 2 3 X1 67&68 52R&L X1 19 X1 X1 X1 X2 18 X1 X1 11R&L X1 78 38 X1 23R&L X2 74A&B X2 104R&L X2 9 9A X6 111 109 X2 X2 M8*1.25*15L 21 94 93R&L X1 X2 X1 X1 D22*D8.5*1.5T X12 60 X8 63 X22 X2 7 D15.4*D8.2*2T X22 D16*D8.5*1.2T X10 9B M8*1.25*20L X8 8 9C M8*1.25*55L X2 14 17 M10*1.5*10T X2 20 M8*15L X4 75 40 M8*1.25*20L X4 73 M6*1*15L X4 107 41 D24*D10*0.4T X6 77 M6*1.0*5T X4 110 108 D11.5*D8*3.
Part list: Part No. 1 2 3 4 5L 5R 6 7 8 9 9A 9B 9C 10 11L 11R 12L 12R 13 14 15 16 17 18 19 20 21 22 23L 23R 24 25 26 27 28 29 30 31 32L 32R 33 34 35 36L 36R 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52L 52R Description Q’ty Main frame Front stabilizer Sliding beam Oval cap Left foot cap Right foot cap Curved washer D22*D8.5*1.5T Spring washer D15.4*D8.2*2T Flat washer D16*D8.5*1.2T Allen bolt M8*1.25*15L Allen bolt M8*1.25*95L Allen bolt M8*1.25*20L Allen bolt M8*1.
Assembly drawing: Step 1 ( x4) ( x2) 81 9A 7 7 D22*D8.5*1.5T 9B 7 M8*1.25*20L ( x4) D15.4*D8.2*2T ( x4) ( x2) ( x2) 20 7 8 1 20 7 8 9B 7 6 2 81 81 19 (A) 9A 7 6 19 3 8 7 9B 6 94 18 7 9C 1 1) Assemble the sliding beam (3) to the rear stabilizer (19) by the Allen bolt (9A), the Allen bolt (9B), the curved washer (6), the spring washer (7) and the flat washer (8).
Step 2 ( x4) 9 M8*1.25*15L 7 D15.4*D8.2*2T (A) ( x2) 9 M8*1.25*15L 7 D15.4*D8.2*2T 10 49 (B) 30 8 7 9 29 6 7 9 22 2 1) Assemble the handlebar post cover (49) to the handlebar post (10) shown as fig. A. 2) Connect the upper computer cable (29) and the lower computer cable (30) shown as fig. B. 3) Assemble the handlebar post (10) to the main frame (1) by the curved washer (6), the spring washer (7), the flat washer (8) and the Allen bolt (9).
Step 3 ( x2) 40 M8*1.25*20L 60 75 52R 52L 60 40 10 23L 75 52L x2 3 Assemble the upper cover (left) (23L), the waved washer (75), the movable handlebar (52L&52R), the flat washer (60) and the bolt (40) to the axle in turn.
Step 4 17 14 73 41 77 41 38 110 109 110 60 108 21 73 77 4-2 4-1 74A 17 14 41 11L 11L 74B 41 31 x2 x2 63 4 1) Assemble the supporting tube for pedal (11L&11R) to the rolling axle (31) by the Nylon nut (17), the flat washer (14) and the plastic flat washer (41) shown as fig. 4-1. 2) Assemble the upper axle cover (74A) and the lower axle cover (74B) to the supporting tube for pedal (11L&11R) by the screw (63) shown as fig. 4-2.
Step 5 M8*1.25*20L ( x2) ( x2) ( x6) ( x2) 12R 12L 32L 5-2 5-1 107 12L 104R 84 63 32L 41 60 40 104L x2 x2 5 1) Assemble the supporting tube for movable handlebar (12L&12R) to the bracket for pedal (32L&32R) by the waved washer (84), the flat washer (60) ,the plastic washer (41) and the bolt (40) shown as fig. 5-1. 2) Assemble the cover for universal joint (104L&104R) to the bracket for pedal (32L&32R) by the screw (63) and the screw (107).
Step 6 101 64 64 65 29 6 ST4*15L ( x16) 6-2 10 52L 52R 23L 52L 63 23R x2 6-1 x2 9B 7 6 52L 12L 6-3 63 93R x2 11L 6 3 93L 1) Connect the upper computer cable (29) and the handle pulse cable (65) to the computer (64). 2) Assemble the computer (64) to the handlebar post (10) by screws that attach to the computer.
Step 7 ( x2) 63 67 107 68 10 107 63 ST4*15L 107 M5*15L 111 105 106 7 78 1) Assemble the left computer bracket (68) and the right computer bracket (67) to the handlebar post (10) by the screw (63) and the screw (107). 2) Assemble the adaptor (78) and turn on the computer. 3) Assemble the bottle holder (106) to the handlebar post (10) by bolt (105). Insert the bolt into the bolt holder.
INSTRUCTION MANUAL OF SM7690-71 【BUTTON FUNCTIONS】 UP To make upward adjustment to each function data or increase training resistance. DOWN To make downward adjustment to each function data or decrease training resistance. MODE To confirm all setting. STAR/STOP To start or stop workout. RESET To reset current setting and have the monitor switch to initial training mode for selection. RECOVERY To test heart rate recovery status.
(3) In the setting mode (Figure 10), press ▲ or ▼ key to adjust M (Manual), P (Program), ♥ (HRC), W (Watt), and U (User) sequentially in circulation order. Figure 10 (4) Press ▲ or ▼ key allows user to have MANUAL (Figure 10) → PROGRAM (Figure 11) → HRC (Figure 12) → WATT (Figure 13) → User Program (Figure 14) → MANUAL in cycle order. Press the MODE key to enter into the MODE function display. Figure 11 Figure 13 (5) i.
(6) PROGRAM SETTING: i. Press ▲ or ▼ key to select one of the 12 PROGRAMS like PROGRAM P01, P02, P03, P04... P12. Corresponding graphics will show flashing texts (Figure 21) on LCD. Figure 21 ii. When a PROGRAM is chosen, the value will be shown in flashing text in the LEVEL column and ready for the adjustment to be determined. Default value will be set as LEVEL1. Press ▲ or ▼ key to adjust the value in LEVEL mode. The console will show instant display graphic according to the changes of adjustments.
(9) When WATT (Figure 34) is selected, the WATT value will be shown in flashing text waiting to be adjusted. Default = 120 will be shown on LCD (Figure 35) User can press ▲ or ▼ to set WATT value. Press the MODE button for confirmation. Press ▲ or ▼ for TIME setting (Figure 36) and start workout by the WATT value and exercise status user inputs for LEVEL value automatic adjustment. WATT value can be adjusted by pressing ▲ or ▼ key.
BODYWORX BODY WORX
