SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS High frequency multi-function tool WU670l
General power tool safety warnings entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
6 Always check walls and ceilings to avoid hidden power cables and 7 8 9 10 11 12 13 14 15 16 17 Warning! Some dust created by power sanding, sawing, grinding and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
Symbols To reduce the risk of injury, user must read instruction manual Double insulation Warning Wear eye protection Wear dust mask Wear ear protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Component list 1 Venting slots 15 13 14 2 Scraper * 3 Dust extraction attachment * 4 Sanding paper * 5 Sanding Pad Perforated * 6 Sanding paper Perforated * 7 Allen key 1 8 Fastening piece 9 Universal end cut blade * 3 10 Carbide grit semicircle saw blade * 11 HSS semicircular saw blade * 12 Carbide rasp, perforated * 13 On/Off switch 14 Variable speed control 15 Sanding pad * 7 16 Adapter 16 *Not all the accessories illustrated or described are included in standard delivery.
Technical data • Voltage Warning: The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used dependant on the following examples and other variations on how the tool is used: 110V~50Hz • Power input 250W • Oscillating speed 11000-20000/min • Oscillating angle 3.2° • Protection class /II • Machine weight 1.4kg How the tool is used and the materials being cut or drilled.
Accessories • Allen key 1 • end cut blade 1 • sanding pad-dust extraction 1 • HSS semicircle saw blade 1 • plastic sanding 1 • carbide grit segment saw blade standard 1 • triangular carbide rasp 1 • plastic sanding pad (unperforated) 1 • dust extraction adapter 1 • sanding sheet (80,120,180# each5) 15 • sanding sheet perforated (80,120,180# each5) 15 • Adapter 2 We recommend that you purchase your accessories from the same store that sold you the tool.
Operation instructions Note: Before using the tool, read the instruction book carefully. Intended Use The power tool is intended for sawing and separating wooden materials, plastic, plaster, non-ferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and for dry A1 A2 grinding of small surfaces. It is especially suitable for working close to edges and for flush cutting. A1 A2 Warning: Before working your tool make sure that no power cords will be damaged.
A1 A2 A1 A2 Reposition the fastening piece (8) and tighten the bolt using the supplied Allen key. 2 USING ADAPTERS (16) (See A3) Accessories of other brands ( Fein®, Bosch® ) can be fitted onto the Sonicrafter® using the adapter. Note: Fein is a registered trademark of C. & E. Fein GmbH. Bosch is a registered trademark of Robert Bosch GmbH. 1) B1 Use the allen key (7) to unscrew the fastening piece (8) and then B2 remove it from the tool holder .
and place it on again. 4 MOUNTING THE SUCTION DEVICE (See C1-D2) When vacuuming, mount the suction device as shown in C1-D2. Note: Using the sanding pad perforated. You can only do the vacuuming after fitting the dust collector. 5 OPERATING THE ON/OFF SWITCH Start the machine, push the On/Off switch (13) forward so that the “I” is indicated on the switch. To switch off the machine, push the On/Off switch (13) toward the rear so that the “0” is indicated on the switch.
8 SAWING WITH THE SEMICIRCLE SAW BLADE The workpiece must be inserted firmly or clamped tightly before it is cut. Typical application: wood, PVC, soft metal sheet. Select high oscillation frequency . The saw blade lasts longer if the wear is distributed evenly. To ensure an even distribution, loosen the saw blade, rotate it and retighten firmly. 9 SAWING WITH THE UNIVERSAL END CUT SAW BLADE (See E) Warning: The sawing teeth are very C3sharp. Do not touch during mounting and application.
Working hints for your tool water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Plug replacement (UK & Ireland only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL BROWN =LIVE As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored blue must be connected to the terminal which is marked with N.
EC DECLARATION OF CONFORMITY We, Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX High frequency multi-function tool Type WU670L Function Sawing,scraping,sanding Complies with the following directives, • EC Machinery Directive 2006/42/EC • EC Low Voltage Directive 2006/95/EC • EC Electromagnetic Compatibility Directive 2004/108/EC Standards conform to EN 55014-1 EN 61000-3-3 EN 55014-2 EN 60745-1 EN 61000-3-2 EN 60745-2-4 The person authorized t
Copyright © 2011, Positec. All Rights Reserved.