SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS High Frequency Multi-function Tool WU675
General power tool safety warnings entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Additional safety points for your tool 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Do not incinerate or burn the battery pack, it may explode. 18 Do not charge a damaged battery pack. 19 Replace any damaged supply cords on your charger. 20 Always disconnect the charger power supply before making or breaking the connections to the battery pack. Never use your Sonicrafter® for wet applications. Always wear eye protection. Always wear ear protection during extended periods of operation.
Symbols • Work in a well-ventilated area. • Work with approved safety equipment, such as those dust masks that are specially designed to filter microscopic particles. Warning: While working with this power tool, hand/arm vibrations occur. Adopt the correct working practices in order to reduce the exposure to vibration. Caution: Do not let familiarity with your Sonicrafter® make you careless. Remember that a careless fraction of a second is sufficient to cause severe injury.
Component list 2 1 LED light 2 On/Off switch 3 Battery pack latch 4 Battery pack 5 Variable speed control 6 Venting slots 7 Sanding pad (Unperforated) * 8 Fastening piece 9 Universal cutting blade 10 Standard cutting blade 11 HSS Semicircle Saw Blade 12 Sanding sheet (Unperforated)* 13 Sanding pad (perforated) * 14 Sanding sheet (perforated)* 15 Sanding finger pad* 16 Sanding finger sheet* 17 Triangular carbide rasp* 18 Carbide grit segment saw blade* 19 Rigid scraping blade* 20 Flexible scraping blade* 2
• • • • Technical data other variations on how the tool is used: Description WORX High Frequency Multi-function Tool Type WU675 (6-designation of machinery, representative of oscillation tool) How the tool is used and the materials being cut or drilled. The tool being in good condition and well maintained The use the correct accessory for the tool and ensuring it is sharp and in good condition. The tightness of the grip on the handles and if any anti vibration accessories are used.
Accessories • 1.3Ah Lithium battery pack (WA3509) • 30min charger (WA3845) • Allen key 2 1 1 We recommend that you purchase your accessories from the same store that sold you the tool. Use good quality accessories marked with a well-known brand name. Choose the type according to the work you intend to undertake. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.
Operating instructions Note: Before using the tool, read the instruction book carefully. Intended Use The power tool is intended for sawing and separating wooden materials, plastic, plaster, non-ferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and for dry grinding of small surfaces. It is especially suitable for working close to edges and for flush cutting.
Operation Warning: Do not touch the gear box after long working time, because it could be hot. 1 MOUNTING THE TOOL (See Fig. B1, B2) Caution: For all work or when changing application tools, always wear protective gloves. Avoid danger of injury from the sharp edges of the application tools. Application tools can become very hot while working, presenting danger of burns! Warning: To reduce the risk of injury, do not let the Universal end cut blades or any segment saw blades face back toward the user’s hand.
3) Fit the adapter onto the tool holder, then place the application tool onto the adapter. Make sure that the tool holder, the adaptor, and the application tool share a flush fit. 4) Reposition the fastening piece onto the application tool and tighten with the Allen key. Note: Make sure the adapter matches the application tool. The adapter (I) is matched to the application tool of Fein®. The adapter (II) is matched to the application tool of Bosch®.(See fig.
Low oscillation frequency: Polishing varnishes. 6 MOUNTING THE SUCTION DEVICE (See Fig. D1, D2) When vacuuming, mount the suction device as shown in D1-D2. Note: Using the sanding pad perforated. You can only do the vacuuming after fitting the dust collector. 7 SANDING Typical application: wood, metal; small areas, especially corners, edges and places difficult to access. Select high oscillation frequency. Sand with a constant movement and light pressure.
10 SCRAPING regarding available recycling and/or disposal options. Discharge your battery pack by operating your tool, then remove the battery pack from the tool housing and cover the battery pack connections with heavy-duty adhesive tape to prevent short circuit and energy discharge. Do not attempt to open or remove any of the components. Typical application: Scraping off old varnish or adhesives, removing glued carpeting, e. g. on stairs or other small to medium-sized surfaces.
Maintenance Plug replacement (UK & Ireland only) Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.
EC Declaration of conformity We, Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX High Frequency Multi-function Tool Type WU675 (6-designation of machinery, representative of oscillation tool) Function Sawing,scraping,sanding Complies with the following Directives, • EC Machinery Directive 2006/42/EC • EC Low Voltage Directive 2006/95/EC • EC Electromagnetic Compatibility Directive 2004/108/EC Standards conform to EN 55014-1 EN 55014-2 EN 60745-1 E
Copyright © 2011, Positec. All Rights Reserved.