SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS ANGLE GRINDER WU736 WU736.1 WU737 WU737.1 WU743 WU743.1 wu743l WU745 WU745.
general power tool safety warnings c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
designed may create a hazard and cause personal injury. 3 Do not use accessories which are not specifically designed 4 5 6 7 8 and recommended by the tool manufacturer, Just because the accessory can be attached to your power tool, it does not assure safe operation. The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool, Accessories running faster than their rated speed can fly apart.
16 Do not use accessories that require liquid coolants. Using 2 Never place your hand near the rotating accessory. Accessory water or other liquid coolants may result in electrocution or shock. 17 Your hand must hold on the handle when you are working. Always use the auxiliary handles supplied with the tool. Loss of control can cause personal injury. 1 may kickback over your hand.
size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges. 5 Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.
Symbols To reduce the risk of injury, user must read instruction manual. Warning Wear eye protection Wear dust mask Wear ear protection Double insulated Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.
Component list 1 2 3 4 5 6 7 8 9 10 11 12 13 14 2 Lock-off & lock-on switch Hand grip area Auxiliary handle Spindle lock button Outer flange Inner flange Spindle Disc * Spanner Protection guard for grinding Clamping screw Coded projection Brush cap Protection guard for cutting * 3 4 1 13 9 8 7 6 5 10 11 12 * Not all the accessories illustrated or described are included in standard delivery.
Technical data Vibration Information Type WU736 WU736.1 WU737 737.1 WU743 WU743.1 WU743L WU745 WU745.1(700-749-designation of machinery, representative of Angle Grinder) WU743L • Voltage • Power input • Rated speed • Protection class • Spindle thread • Disc size • Disc bore • Machine weight WU736 WU736.1 WU737 WU737.1 110V~50Hz 2 Typical weighted Vibration emission value ah = 7.29m/s vibration Uncertainty K = 1.5m/s² WU745 WU745.1 220-240V~50/60Hz 2000W 6600/min WU743 WU743.
significantly reduce the exposure level over the total working period. Helping to minimise your vibration exposure risk. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate). If the tool is to be used regularly then invest in anti vibration accessories. Avoid using tools in temperatures of 100C or less. Plan your work schedule to spread any high vibration tool use across a number of days.
Operating instructions Note: Before using the tool, read the instruction book carefully. INTENDED USE The machine is intended for cutting, roughing and brushing metal and stone materials without using water.For cutting metal, a special protection guard for cutting ( accessory) must be used. A Assembly and adjustment 1 1 MOUNTING THE PROTECTIVE DEVICES AUXILIARY HANDLE For all work with the machine, the auxiliary handle (3) must be mounted.
Actuate the spindle lock button (4) only when the grinder spindle is at a standstill! 2 GRINDING/CUTTING DISC Pay attention to the dimensions of the grinding disc. The mounting hole diameter must fit the inner flange (6) without play. Do not use reducers or adapters. When using a diamond cutting disc, take care that the directionof-rotation arrow on the diamond cutting disc and the direction of rotation of the machine (direction-of-rotation arrow on the machine head) agree.
the coded groove on the spindle collar of the machine head and rotate to the required position (working position). The closed side of the protection guard (10/14) must always point to the operator. Tighten clamping screw (11). b Operation D Starting Operation Your switch is locked off to prevent accidental starting. To switch on your tool, push the safety switch lever (B) forward and depress on/off switch (A) fully. Now your tool is switch on. To switch off your tool, just release the On/Off switch.
Operating Instructions • Clamp the workpiece if it does not remain stationary due to its own weight. • Do not strain the machine so heavily that it comes to a standstill. • Grinding and cutting discs become very hot while working; do not touch until they have cooled. • Pull the plug from the socket-outlet when not using the machine. With the plug inserted and mains voltage existing, the power tool still has low power consumption even when it switched off.
The machine must always work in an up-grinding motion. Therefore, never move the machine in the other direction! Otherwise, the danger exists of it being pushed uncontrolled out of the cut. 15 17 Auto-stop carbon brushes When the Resin Insulating Tip (15) inside the Carbon Brush (16) is exposed to contact the commutator (17), it will automatically shut off the motor. When this occurs, both carbon brushes should be replaced. Keep the carbon brushes clean and free to slip in the holders.
Working hints for your angle grinder Maintenance Remove the plug from the socket before carrying out any adjustment, servicing or maintenance. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust.
Plug replacement (Uk & ireland only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL BROWN = LIVE As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored blue must be connected to the terminal which is marked with N.
ec Declaration of conformity We, Positec Power Tools (Europe)Ltd, PO Box 152, Leeds, LS10 9DS,UK Declare that the product, Description WORX Angle grinder Type WU736 WU736.1 WU737 WU737.1 WU743 WU743.1 wu743L WU745 WU745.
Copyright © 2012, Positec. All Rights Reserved.
