SAFETY AND OPERATING MANUAL Original instructions WX254 WX254.
General Power Tool Safety Warnings WARNING: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term power tool in the warnings refers to your mains-operated (corded) power tool or batteryoperated (cordless) power tool. 2 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) c) d) e) f) g) of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting.
that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc.
SYMBOL Do not stare directly into the tool holder. When changing the tool insert, it can be thrown out toward the front.
7 1 6 2 3 8 6 5 4 9
1. Cover 2. Forward/Reverse Rotation Control 3. Soft Grip Handle 4. On/Off Switch 5. LED Light 6. Bit Holder or Chuck 7. Bit Cartridge 8. Charging Indicator 9. Charging Socket TECHNICAL DATA Charger voltage Rated voltage Rated speed Machine weight Charging time 230V/240V~50Hz 4V Max* 230/min 0.5kg 3~5 hours * Voltage measured without workload. Initial battery voltage reaches maximum of 4 volts. Nominal voltage is 3.6 volts.
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. a1 8 a2 BEFORE OPERATING THIS TOOL A) CHARGE THE BATTERY The battery charger supplied is only for the Li-Ion battery installed in the machine. Do not use another battery charger. The Li-Ion battery is protected against deep discharging. When the battery is empty, the machine is switched off by means of a protective circuit: The Chuck (6) no longer rotates.
Charger. Disconnect the Charger from the screwdriver. The screwdriver is ready to be used. Important: When charging, the Charger and screwdriver may become warm to the touch; this is normal and does not indicate a problem. 2. OPERATING INSTRUCTIONS Inspect the screwdriver before using to ensure all the parts are running smoothly and there are no abnormal sounds or sparks. Before driving fasteners, check behind walls for wires and other electrical hazards or plumbing. OPERATION b 9 1.
2. Move the top Cover back and forth until the desired bit is in place. If the bits in the Bit Cartridge need to be replaced, remove Bit Cartridge by pushing it up from the window underneath. Replace the bits with the desired bits. Ensure the bits are properly positioned in the Cartridge and are not protruding from the back of the Bit Cartridge. Or, simply pull a bit from the holder, and replace it with the desired bit. It will load into the Cartridge automatically when the cover is opened (See Fig. D).
3. SWITCH LOCK The On/off Switch (4) can be locked in the OFF position. This helps to reduce the possibility of accidental starting when the screwdriver is not in use. To lock the On/off Switch, place the Forward/Reverse Rotation Control (2) in the center position. 4. FORWARD/REVERSE ROTATION CONTROL (See Fig. E1, E2) For drilling and screw driving in a clockwise rotation, move the switch marked “ ” lever to the left. For reverse rotation, move the switch marked “ ” lever to the right).
5. FULLY AUTOMATIC SPINDLE LOCKING (AUTO-LOCK) (See Fig. F) The screwdriver Chuck (6) is locked when the On/Off Switch (4) is not pressed. This allows the driver to be used manually when needed. Important: When using as a manual tool, do not press the On/Off Switch (4). Otherwise the screwdriver will be damaged. f 12 6. USING THE LED LIGHT To turn on the Light (5) simply press the On/Off Switch. When you release the On/Off Switch, the Light will go off.
MAINTENANCE Your tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.
www.worxtools.com Copyright © 2012, Positec. All Rights Reserved.
