SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Electric Circular Saw WX422
8 10 2 3 4 1 9 16 7 12 6 15 11 5
A 1 2 13 C B 2 1 D1 D2 E1 E2 17 14
E1 E2 F1 F2 3 1 2 G1 G2 G3 G4
G3 G5 G4
1. LOCK OFF BUTTON 2. SOFT GRIP HANDLE 3. HEX KEY 4. ON/OFF SWITCH 5. SPINDLE LOCK BUTTON 6. LOWER BLADE GUARD 7. LOWER GUARD LEVER 8. FIXED UPPER GUARD 9. DUST EXTRACTION OUTLET 10. VACUUM ADAPTER 11. DEPTH ADJUSTMENT LEVER 12. BASE PLATE 13. SAW BLADE (See Fig. A) 14. BLADE BOLT (See Fig. A) 15. PARALLEL GUIDE 16. PARALLEL GUIDE CLAMPING FIXTURE 17. OUTER FLANGE (See Fig. A) Not all the accessories illustrated or described are included in standard delivery.
TECHNICAL DATA Type WX422 (4 - designation of machinery, representative of Saw) Voltage 230–240V~50Hz Rated power 350W No load (rated) speed 3600/min Blade size TCT blade 85 mm X 1.2 mm X 15 mm X 24T HSS blade 85 mm X 1.2 mm X 15 mm X 44T Diamond disc 85 mm X 1.2 mm X 15 mm X 60G Max cutting depth 27mm Recommended maximum material thickness 8 Wood 27mm Aluminum 3mm PVC pipe (radius) 13mm Tile 8mm Sheet steel 0.91mm Spindle thread size M5 Saw blade thickness TCT blade 0.
We recommend that you purchase your accessories from the same store that sold you the tool. Use good quality accessories marked with a well-known brand name. Choose the type according to the work you intend to undertake. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. NOISE INFORMATION A weighted sound pressure LpA: 82dB(A) A weighted sound power LwA: 93dB(A) KPA& KWA 3.0dB(A) Wear ear protection.
GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 10 1. WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
4. POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator. - When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator. - If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.
ADDITIONAL SAFETY RULES FOR YOUR CIRCULAR SAW g) 1. Always wear a dust mask, hearing protection and eye protection. 2. Only use saw blades recommended in the specification. 3. Use only blade diameter(s) in accordance with the markings. h) ADDITIONAL SAFETY RULES FOR YOUR CUTTING-OFF MACHINES i) a) The guard provided with the tool must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator.
performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. m)Position the cord clear of the spinning accessory. lf you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning wheel. n) Never lay the power tool down until the accessory has come to a complete stop.
in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece. i ) Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
SYMBOLS To reduce the risk of injury, user must read instruction manual Metal Double insulation Plastic Warning Tile Wear ear protection Incorrect Wear eye protection Correct Wear dust mask Lock 16 Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice. Before any work on the machine itself, pull the mains plug from the socket outlet.
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. INTENDED USE: The tool is intended for ripping and crosscutting wood and other materials in straight cutting lines, while resting firmly on the work piece. ASSEMBLY AND OPERATION Action Figure Saw blade Assembly and Removing See Fig. A Safety On/Off Switch See Fig. B Sawdust Removal See Fig. C Cross and Rip Cutting See Fig. D1, D2 Parallel Guide See Fig. E1, E2 Cutting Depth Adjusting See Fig.
TROUBLE SHOOTING Symptom Possible Causes Possible Solution Tool will not start when operating the on/off switch. Power cord not plugged in. Power cord is broken. Carbon brush has worn down Check to make sure power cord is connected well into a working outlet. Unplug the power cord. Replace it using a qualified maintenance person. Replace the carbon brush using a qualified maintenance person. Cutting depth is less than that is set. Sawdust accumulated at the rear of the base. Shake out sawdust.
PLUG REPLACEMENT ( UK & IRELAND ONLY ) DECLARATION OF CONFORMITY If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL Brown = Live As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows.
www.worx.com Copyright © 2015, Positec. All Rights Reserved.
