Technical data

ManualsBrandsWorx ManualsPower ToolsWX426

Electric Circular Saw WX426

SAFETY AND OPERATING MANUAL

Summary of content (16 pages)

PAGE 1
SAFETY AND OPERATING MANUAL Electric Circular Saw WX426
PAGE 2
PAGE 3
13 1 12 11 2 10 3 4 9 5 8 6 7 15 14
PAGE 4
A 1 2 16 C1 B 2 1 C2 D1 D2 E 19 18 17
PAGE 5
D2 E F1 F2 19 20 F3 G1 G2 H1
PAGE 6
G2 H1 H2 I
PAGE 7
1. SOFT GRIP HANDLE 2. FIXED UPPER GUARD 3. VACUUM ADAPTER 4. DUST EXTRACTION OUTLET 5. PARALLEL GUIDE CLAMPING FIXTURE 6. PARALLEL GUIDE 7. LOWER BLADE GUARD 8. BASE PLATE 9. LOWER GUARD LEVER 10. DEPTH ADJUSTMENT LEVER 11. LOCK OFF BUTTON 12. ON/OFF SWITCH 13. HEX KEY 14. SPINDLE LOCK BUTTON 15. LASER 16. SAW BLADE (See Fig. A) 17. BLADE BOLT (See Fig. A) 18. OUTER FLANGE (See Fig. A) 7 19. LASER ON-OFF SWITCH (See Fig. E) 20. LASER BATTERIES (TWO) (See Fig.
PAGE 8
TECHNICAL DATA Type WX426 (4 - designation of machinery, representative of Saw) Voltage 230-240V~50Hz Rated power 400W No load (rated) speed Blade size 3600/min TCT blade 85mmx15mmx1.2mmx24T HSS blade 85mmx15mmx1.2mmx44T Diamond disc 85mmx15mmx1.2mmx60G Max cutting depth 27mm Wood Aluminum Recommended maximum material thickness PVC pipe (diameter) Tile Sheet steel Protection class Bare tool weight 27mm 3mm 13mm 8mm 0.91mm /ll 1.
PAGE 9
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1 WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
PAGE 10
4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
PAGE 11
FURTHER SAFETY INSTRUCTIONS FOR ALL SAWS KICKBACK CAUSES AND RELATED WARNINGS - Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator. - When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.
PAGE 12
ADDITIONAL SAFETY RULES FOR YOUR CIRCULAR SAW 1. Only use saw blades recommended in the specification. 2. Do not use any abrasive wheels. ADDITIONAL SAFETY WARNING FOR CLASS 2 LASER The laser device fitted to this tool is CLASS 2 with a maximum radiation of 1.5mW and 650nm wavelength. CLASS 2 LASER RADIATION, DO NOT STARE INTO BEAM GENERAL SAFETY WARNINGS FOR YOUR LASER 12 WARNING: Read all safety warnings and all instructions.
PAGE 13
SYMBOLS To reduce the risk of injury, user must read instruction manual Wood Double insulation Aluminium Warning Metal Wear ear protection Plastic Wear eye protection Tile Wear dust mask Incorrect Do not stare into beam Correct Laser radiation Lock RCM marking Unlock Before any work on the machine itself, pull the mains plug from the socket outlet.
PAGE 14
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. Recommendation that the tool always be supplied via a residual current device with a rated residual current of 30 mA or less INTENDED USE: The tool is intended for ripping and crosscutting wood and other materials in straight cutting lines, while resting firmly on the work piece. ASSEMBLY AND OPERATION Action 14 Figure Saw blade Assembly and Removing See Fig. A Safety On/Off Switch See Fig.
PAGE 15
TROUBLE SHOOTING Symptom Possible Causes Possible Solution Tool will not start when operating the on/off switch. Power cord not plugged in. Power cord is broken. Carbon brush has worn down Check to make sure power cord is connected well into a working outlet. Unplug the power cord. Replace it using a qualified maintenance person. Replace the carbon brush using a qualified maintenance person. Cutting depth is less than that is set. Sawdust accumulated at the rear of the base. Shake out sawdust.