Cordless Circular Saw EN P02 Scie circulaire sans fil F P14 Sierra circular inalámbrica ES P23 WX529L WX529L.
PRODUCT SAFETY WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints; • Crystalline silica from bricks and cement and other masonry products • Arsenic and chromium from chemically-treated lumber.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second. 4. POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off.
e) Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock. f) When ripping always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade binding. g) Always use blades with correct size and shape (diamond versus round) of arbor holes.
ADDITIONAL SAFETY RULES FOR YOUR CIRCULAR SAW 1. 2. 3. 4. 5. Only use saw blades recommended in the specification. Do not use any abrasive wheels. Use only blade diameter(s) in accordance with the markings. Identify the correct saw blade to be used for the material to be cut. Use only saw blades that are marked with a speed equal or higher than the speed marked on the tool.
SYMBOLS To reduce the risk of injury, user must read instruction manual Warning Lock Unlock Wear ear protection Wear eye protection Wear dust mask POSITEC Inc. has established a partnership with the RBRC Corporation to recycle any Positec batteries with the RBRC-call2recycle seal. For environmental protection, please do not discard batteries in the trash. After the batteries’ life cycle is ended, then please call 1-800-822-8837 for a free service that will properly dispose of the battery.
15 1 2 3 14 13 12 10 4 5 9 6 11 7 8 Cordless Circular Saw EN 7
LOCK-OFF BUTTON 2. ON/OFF SWITCH 3. FRONT HANDLE 4. SPINDLE LOCK BUTTON 5. BASE PLATE ANGLE SCALE 6. BASE PLATE BEVEL LOCK KNOB Voltage 7. CUTTING MARK, 45° No load speed 8. CUTTING MARK, 0° Blade size 5-1/2” (140mm) 9. BASE PLATE Blade bore 3/8” (10mm) 10. LOWER GUARD LEVER 11. LOWER BLADE GUARD 12. FIXED GUARD 13. DUST ADAPTER 14. BATTERY PACK * 15. BATTERY PACK RELEASE BUTTON * 8 TECHNICAL DATA 1. Type WX529L WX529L.
A1 1 A2 2 A3 B 9 19 20 C 18 17 16 D 1 2 21 23 22 24 25 E F Cordless Circular Saw 2 45 o 7 EN
E F 7 45o 2 0o 1 3 G 8 H 10 26 Cordless Circular Saw 13 EN
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. INTENDED USE: The tool is intended for ripping and cross-cutting wood and other materials in straight cutting lines, while resting firmly on the work piece. ASSEMBLY AND OPERATION ACTION FIGURE BEFORE OPERATION Removing the battery pack See Fig. A1 Charging the battery back See Fig. A2 Installing the battery pack See Fig.
TROUBLESHOOTING Symptom Possible Causes Possible Solution Tool will not start when operating the on/off switch. Battery pack not plugged in. Check to make sure battery pack is connected well into a working outlet. Charging the battery. Replace the carbon brush using a qualified maintenance person. Cutting depth is less than that is set. Sawdust accumulated at the rear of the base. Shake out sawdust. Consider connecting a vacuum for dust collection.
