Cordless Circular Saw EN P03 Scie circulaire sans fil F P15 Sierra circular inalámbrica ES P24 WX530L WX530L.
PRODUCT SAFETY WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints; • Crystalline silica from bricks and cement and other masonry products • Arsenic and chromium from chemically-treated lumber.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second. 4 4. POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off.
support the work properly to minimize body exposure, blade binding, or loss of control. e) Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock. f) When ripping always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade binding.
ADDITIONAL SAFETY RULES FOR YOUR CIRCULAR SAW 1. 2. 3. 4. Only use saw blades recommended in the specification. Do not use any abrasive wheels. Use only blade diameter(s) in accordance with the markings. Identify the correct saw blade to be used for the material to be cut. GENERAL SAFETY WARNINGS correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions. 15) When possible, remove the battery from the equipment when not in use.
Wear protective gloves Wood Carbide Tipped Blade Lock Unlock POSITEC Inc. has established a partnership with the RBRC Corporation to recycle any Positec batteries with the RBRC-call2recycle seal. For environmental protection, please do not discard batteries in the trash. After the batteries’ life cycle is ended, then please call 1-800-822-8837 for a free service that will properly dispose of the battery.
5 4 3 2 1 11 0o 10 9 6 7 8 12 13 14 15 16 17 18 19 20 21
1. SAFETY BUTTON 0-50° Bevel capacity 2. ON/OFF SWITCH Machine weight 3. FRONT HAND GRIP 5.9 lbs 5.1 lbs **Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts. 4. CUTTING MARK, 0° 5. CUTTING MARK,45° 6. MAIN-BASE PLATE 7. BASE PLATE BEVEL LOCK KNOB 8. BASE PLATE BEVEL ANGLE SCALE ACCESSORIES 9. HEX KEY WX530L WX530L.9 Carbide Tipped Blade 1 1 Vacuum adapter 1 1 Hex Key 1 1 14.LOWER GUARD LEVER Battery Pack 1 / 15.
A2 A1 1 2 C B 22 23 E D 2 1 1 2 3 24
G F 5 45o 4 0o I H 1 0~1-5/8’’ (0-43mm) 25 12 J K1 >9”(230mm) >9”(230mm) STA STA NDARD ESTÁNDARD NDA R ≤3/4” ≤3/4” (20mm) (20mm) >9”(230mm) >9”(230mm)
K2 K3 K4 K5
ASSEMBLY AND OPERATION ACTION FIGURE BEFORE OPERATION Removing and installing the battery pack See Fig. A1 Charging the battery pack See Fig. A2 ASSEMBLY Saw blade Assembly and Removing WARNING: Always remove the battery before changing the blade! See Fig. B Hex key storage See Fig. C OPERATION Safety On/Off Switch WARNING: To avoid cutting injury from the sharp blade, please don’t put your hands around the Base Plate. See Fig. D Cutting Depth Adjusting See Fig. E Cutting Guide See Fig.
MAINTAIN TOOLS WITH CARE Remove the battery before carrying out any adjustment, servicing or maintenance. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool.
www.worx.com Copyright © 2017, Positec. All Rights Reserved. Copyright © 2017, Positec. Tous droits réservés. © Derechos reservados 2017, Positec. Todos los derechos reservados.
