SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Oscillating Multi-Tool WX686 WX686.
PRODUCT SAFETY GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings, instructions, illustrations and b) c) specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or batteryoperated (cordless) power tool.
power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
2 3 1 4 4 5 6 Oscillating Multi-Tool WX686 WX686.
A B1 2 3 B2 B3 2 2 5 3 C Oscillating Multi-Tool 3 D WX686 WX686.
E F G 6 Oscillating Multi-Tool WX686 WX686.
COMPONENT LIST NOISE INFORMATION 1. ONBOARD CLIP-IN WRENCH 2. ON/OFF SWITCH A weighted sound power 3. VARIABLE SPEED CONTROL KpA& KwA 4. VENTING SLOTS 5. UNIVERSAL FIT™ INTERFACE * 6. FLANGE A weighted sound pressure VIBRATION INFORMATION TECHNICAL DATA Type Designation WX686 WX686.
If the tool is to be used regularly then invest in anti vibration and noise accessories. Plan your work schedule to spread any high vibration tool use across a number of days. OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. INTENDED USE The power tool is intended for sawing and remodeling wooden materials, plastic, plaster, nonferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and for dry grinding of small surfaces.
APPLICATION WARNING: The sawing teeth are very sharp. Do not touch during mounting and application. The workpiece must be clamped tightly before it is cut.
blade or other accessory as applicable, rotate it and retighten firmly. Cut/Sand with a constant movement and light pressure. Heavy pressure does not increase the cut/removal rate – the accessory merely wears faster. WORKING HINTS FOR YOUR TOOL 10 If your power tool becomes too hot, especially when used at low speed, set the speed to maximum and run it with no load for 2-3 minutes to cool the motor. Avoid prolonged usage at very low speeds. Always keep the blade sharp.
DECLARATION OF CONFORMITY We, Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany Declare that the product Description WORX Sonicrafter® Type Designation WX686 (6-designation of machinery, representative of Oscillating MultiTool) Function Sanding, sawing, rasping, scraping, polishing Complies with the following Directives: 2006/42/EC 2014/30/EU 2011/65/EU&(EU)2015/863 Standards conform to EN 62841-1 EN 62841-2-4 EN 55014-1 EN 55014-2 EN IEC 61000-3-2 EN 61000-3-3 The person authorized to compile
DECLARATION OF CONFORMITY We, Positec Power Tools (Europe) Ltd, PO Box 6242, Newbury, RG14 9LT, UK On behalf of Positec declare that the product Description WORX Electric Circular Saw Type WX426 (4-designation of machinery, representative of Saw) Function Cutting various materials with a rotating toothed blade Complies with the following regulations: Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility Regulations 2016 The Restriction of the Use of Certain Hazardous Substances in Elec
