Thanks for buying the KG-UV920P-E mobile radio. This mobile radio offers latest design, enhanced features, solid performances and easy accessibility. We believe you will be pleased with the high quality and reliable features for all your communication needs. Read this important information on the safe and efficient operation before using mobile radio.This manual is suitable for KG-UV920P-E.
Safety information Safety information Twin Band FM Transceiver EU Regulatory Conformance As certified by the qualified laboratory, the product is in compliance with the essential requirements and other The KG-UV920P-E is an electrical apparatus, as well as a generator of RF(Radio Frequency) energy, and you should exercise all safety precautions as are appropriate of this type of device. These safety tips apply to any device installed in a well-desi-gned amateur radio station.
Safety information Contents Twin Band FM Transceiver In mobile installations, it is preferable to mount your antenna on top of the roof of the vehicle, if feasible, so as to utilize the car body as a counterpoise for the antenna and raise the radiation pattern as far away from passengers as possible. During vehicular operation when stopped(in a parking lot, for example), make it a practice to switch to Low power if there are people walking nearby.
Contents Step frequency settings (STEP) ----- Menu 1 Wide/Narrow bandwidth settings (W/N) ----- Menu 2 Two medium level power settings (MPOWSET) ----- Menu 3 Offset frequency settings (OFF-SET) ---- Menu 4 Transmission prompt settings (ROGER) ----- Menu 5 Beep prompt settings (BEEP) ----- Menu 6 Voice prompt settings (VOICE) ----- Menu 7 Busy channel lock-out (BCL) ----- Menu 8 Mute settings (SP-MUTE) ----- Menu 9 Scan mode settings (SC-REV) ----- Menu 10 Transmission time-out timer (TOT) ----- Menu 11 Tra
Checking the equipment Contents Remote control (RC-SW) ----- Menu 44 Reset settings (RESET) ----- Menu 45 How to operate the FM radio Turning on Tuning radio stations Storing and calling out FM radio stations Exiting the FM radio mode Repeater usage Repeater PTT option Repeater SPK option Cross-band repeater entry and exiting Hand microphone encoding function Remote control function Remote control activation Stun Kill Monitoring Inspection Remote control power on / off Remote changing settings Wire-clo
Frequency Range Suitable for any Region of any Country: (RX / TX) 136-174MHz & 400-470MHz 136-174MHz & 400-480MHz 136-174MHz & 216-280MHz 136-174MHz & 420-520MHz 144-146MHz & 430-440MHz 144-148MHz & 222-225MHz 144-148MHz & 420-450MHz (RX) FM: 65MHz~108MHz ( 100K Frequency Spacing ) Band can be Set Freely V/U U/V V/V U/U Dual Reception Twin Band Simultaneous Reception Dual Display Large LCD Dual Frequency Display, Two Completely Independent Operating Systems Over 999 Memory Channels Area Scanning Management
Pre-use installation Transceiver installation Choose a safe place inside your vehicle, one which would to the greatest extent reduce possible harm to passengers inside the car while the car is moving. It is recommended to install the transceiver on the lower part of the front meter gauge, it will prevent the transceiver from colliding with the driver in the instance of emergency or sudden braking.
Connecting power source The transceiver power source usage ranges from 13.8V±15%. When your power source (or vehicle power source) reaches levels up to 16V, TX will be forbidden, however RX will operate as normal. When your power source (or vehicle power source) reaches levels as low as 11.5V, the transceiver will automatically shut off. So the transceiver does not exhaust the vehicles battery and affect the vehicles normal operation.
Front panel installation The transceiver is supplied with two kinds of switchboard panels•Inclined switchboard panel and a flat switchboard panel.
Front panel installation Connection method for transceiver station to operating front panel• Special Reminder The vehicle transceiver connection line uses 8 facets and 8 lead conducting wires (diagram 1), ! If the connection wires are not Company supplied or dealer approved, Company does not guarantee its safety and operational effectiveness! Diagram 1 The two ends of the facets connect to the corresponding line: (Take note that direction of the connection lines on the left and right sides of the facet
Accessories installation Getting started •2•First string the connection line through opening in the center of the support bracket•then close the bracket cover directly Front panel as shown by the arrows. LCD KG-UV920P-E Outer speakers QT DT MEMCH The external speaker jacks can be connected to a 3.5mm single outlet. There are two speaker outlets located on the back of the transceiver.
