Instructions

Item No.: 3500 11 64
VBD 595-2-1 (01.19)
9. Warranty conditions
Subject to technical modifications, misprints and errors. Illustrations not binding.
RADEMACHER Geräte-Elektronik GmbH provides a 24-month warranty for
new systems that have been installed in compliance with the installation
instructions. All construction faults, material defects and manufacturing
defects are covered by the warranty.
Your statutory warranty claims shall remain unaffected by this warranty.
The following are not covered by the warranty:
◆ Incorrect fitting or installation
◆ Non-observance of the installation and operating instructions
◆ Improper operation or wear and tear
◆ External influences, such as impacts, knocks or weathering
◆ Repairs and modifications by third parties, unauthorised persons
◆ Use of unsuitable accessories
◆ Damage caused by unacceptable excess voltage (e.g. lightning)
◆ Operational malfunctions caused by radio frequency overlaps and
other such radio interference
For the warranty to be applicable, the new device must have been purchased
through one of our approved specialist retailers. Proof of this can be provided
by pre-senting a copy of the bill.
RADEMACHER shall remedy any defects, which occur within the warranty
period free of charge either by repair or by replacement of the affected parts
or by supply of a new replacement unit or one to the same value. There is no
general extension of the original warranty period by delivery of a replacement
or by repair as per the terms of the warranty.
DuoFern Switch Adapter Plug 9472
Operating Manual
RADEMACHER
Geräte-Elektronik GmbH
Buschkamp 7
46414 Rhede (Germany)
[e-mail]
www.rademacher.de
Service:
Hotline [phone]*
Fax [phone]
[e-mail]
8. Simplified EU Declaration of Conformity
* 30 seconds free of charge, subsequently
14 cents / minute from German fixed line
networks and max. 42 cents / minute from
German mobile networks.
RADEMACHER Geräte-Elektronik GmbH hereby declares that
the DuoFern Switch Adapter Plug complies with the Directive
2014/53/EU (Radio Equipment Directive).
The full text of the declaration of conformity is available at the
following website:
www.rademacher.de/ce
You must assign every required DuoFern transmitter to the DuoFern Switch
Adapter Plug in order that the DuoFern Switch Adapter Plug can be controlled with
a DuoFern transmitter. You can assign a maximum of 20 DuoFern transmitters
(e.g. HomePilot®; DuoFern manual transmitter standard etc.).
1. Switch the desired DuoFern transmitter to registering mode (please
refer to the corresponding operating instructions).
Registering mode remains active for 60 seconds.
2. Press either the switch 3 Connect (login)" or the switch  "Disconnect
(logout)" on the bottom of the DuoFern Switch Adapter Plug.
3. The DuoFern Switch Adapter Plug then transmits either a log-on or
log-off signal.
- The status LED flashes green during login.
- The status LED flashes red during logout.
4. If registration is successful, the status LED will light up constantly green
for approx. 20 seconds.
5. Log the next DuoFern transmitter on / off. In order to do so, repeat steps
1 to 3.
NOTE
The status LED lights up red if the registration process fails, for example
if:
- 20 DuoFern transmitters have already been registered.
- An unsuitable device (e.g. other DuoFern actuator) is registered.
- An attempt was made to log-off a DuoFern transmitter that is not
logged-on.
5. Logging DuoFern transmitters on / off
6. Erase data (Reset)
1. Press and hold the "Disconnect button"  until the status LED lights
up constantly red.
2. All of the registered DuoFern transmitters are logged-off.
3. Subsequently, the DuoFern Switch Adapter Plug will be reset to its
original supplied state.
7. Technical Specifications
Supply voltage: 230 V / 50 Hz
Standby consumption: 0.5 W
Switching capacity: max. 1300 W
Protection class: II (only for use in dry areas)
Transmission frequency: 434.5 MHz
Transmission power: max. 10 mW
Dimensions (without plug):
- W x H x D: 64 x 106 x 41 mm