Owner Manual

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
CONNECTING THE WIRES
2. Attachthexture’swirestothehousewirespulledfromthe
junctionbox.Trimexcesswiresuntil8to10inchesremainfor
connecting.Connectblacktoblack(orsmooth);whitetowhite(or
ribbed);groundtoground(greenorcopper).Twisttheendsofthe
wirepairstogether,thentwistonawireconnector.Makesureall
twistsareinthesamedirection.Ifthereisnogroundwire(greenor
copper)fromthejunctionbox,locategroundscrew(E)onmounting
strap(B)andwrapthexture’sgroundwirearoundthegreenground
screw(E).Useascrewdrivertosecuregroundscrew(E)ontothe
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
For Customer Service, please
contact the place of purchase.
A
ssemblyInstructions
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the
important notes above. Shut off the power at the
circuit breaker and completely remove the old xture
from the wall, including the old mounting strap.
1. Takethemountingstrapassemblyfromthepartsbag.
Mountingstrap(B)containsseveralthreadedholes.
Twosetsofmountingscrews(A)shouldbeattached
tomountingstrap(B).Youmayneedtotightennuts
(C) thatholdthesescrewsinplace.Ifthescrewsare
notattached,pleaseholdcanopy(F)uptomounting
strap(B).Lineuptheholesincanopy(F)withtheholes
inmountingstrap(B)andinsertmountingscrews(A)
intomountingstrap(B)sothatmountingscrews(A)
protrudethroughtheholesincanopy(F).Mounting
screws(A)arelong,sopleasetestthecanopyagainst
themountingstraptoseehowfaryoushouldinsertthe
screws.Removethecanopy(F)andtightennuts(C)onto
mountingscrews(A)toholdthescrewsinplace.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
FINISHING THE INSTALLATION
3. Connectjoint(H)ofthecanopy(F)tothenipple(I)ofthexturebody.Hangthesidepoles(K)onthehooks(J)foundatthetopofthe
xturebodynearnipple(I).
4. Pushcanopy(F)uptotheceilinguntilmountingscrews(A)protrudefromtheholesinthecanopy(F).Tightlythreaddeconuts(G)
ontotheexposedthreadsofmountingscrews(A)untilthecanopyissnugagainsttheceiling.
6. Attachsocketcovers(L)overtheexposedsockets.
Installlightbulbs(notprovided)basedonthexture’sspecications.Donotexceedthemaximumwattage.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
G
N
D
A
E
D
B
C
F
G
H
I
J
K
L