(Not Included) Page 1 of 19
Page 2 of 19
Page 3 of 19
Page 4 of 19
Page 5 of 19
BUFFET .6" 15 47 A B 1PC C 1PC D 1PC E 1PC F 1PC .24 " F B A 1PC H O C I H 1PC G 1PC 38.89" O I 1PC K J 1PC K 1PC L 2PCS D DIMENSIONS: 1 25PCS 7 2PCS M 5PCS 2 25PCS 0.47" 8 4PCS 3 60PCS 4 8PCS 0.98" 9 12PCS N 2PCS O 2PCS P 3PCS 5 4PCS 6 24PCS 0.59" 1.5" 4PCS 16PCS 4PCS 1PC 8 Sets 0.59" 1PC 1PC 1PC 1.26" 1PC 2PCS 1PC 0.
Get Ready Please group boards as below F 1PC K 1PC H 1PC I 1PC G 1PC J 1PC B 1PC L 2PCS A 1PC E 1PC N 1PC M 5PCS N 1PC C 1PC D 1PC Body P 3PCS O 2PCS Doors /Shelf Page 7 of 19
STEP : 1 1 Hardware 1 x 25PCS Hardware 3 x 28PCS 1 1 1 1 3 1 1 1 A 3 3 B 3 1 1 1 1 3 C 3 3 3 3 E 3 1 1 1 E 3 1 3 3 3 F 1 3 3 1 3 3 3 1 J Dowel hole 3 1 1 3 1 3 1 3 3 1 1 H K 3 3 Page 08 of 19 3 3
STEP : 2 3 Hardware 3 x 32PCS 3 3 3 M G 3 3 3 3 3 x5 N 3 3 I 3 3 Dowel hole 3 STEP : 3 Hardware 5 x 4PCS Hardware 6 x 8PCS Hardware 7 x 2PCS Hardware 8 x 4PCS 5 6 Align hinges (#5) to panels (#O), then secure by using screws (#6).
STEP : 4 Refer to page 5 on how to secure cam locks (#2) onto cam bolts (#1).
STEP : 7 Hardware 2 x 2PCS Finish Side M F E 2 G 2 STEP : 8 Hardware 2 x 1PC Finish Side N 2 M M M M E Page 11 of 19
STEP : 9 Hardware 2 x 2PCS x 2PCS Hardware Cover cam locks (#2) on panel (#K) by using stickers (#21).
STEP : 11 Hardware 2 x 1PC Finish Side N B 2 Dowel hole STEP : 12 M B Page 13 of 19
STEP : 13 Hardware 2 x 4PCS 2 2 2 2 C STEP : 14 Hardware 2 x 7PCS Hardware x 7PCS Hardware x 1PC 2 2 2 2 Use stickers (#21) on cam locks (#2) in this step.
STEP : 15 Hardware x 1PC L L L L Flip unit upside down and slide back panels (#L) with divider (#13) through the grooves of the unit.
STEP : 17 Hardware Hardware x 16PCS x 4PCS D Low High The low area of parts (#11) is always facing towards the corner of panel (#D). STEP : 18 Hardware Hardware Hardware Hardware x 4PCS x 1PC x 1PC x 1PC D Attach the longest part of threaded bolts (#25) onto center support leg (#24).
STEP : 19 Hardware 9 x 12PCS 9 Attach shelf pins (#9) to the desired height of the shelves (#P). 9 9 9 P 9 9 P 9 9 9 9 P Align hinges of panel (#O) to the unit, the secure by using screws (#6). STEP : 20 Hardware 6 x 16PCS 6 6 6 6 O O Adjust length of hinges. Adjust depth of hinges.
STEP : 21 Hardware x 8 Sets Insert fixative plates (#14) all around the grooves of the back panels, then secure by using screws (#14). STEP : 22 Hardware Hardware Hardware Hardware Hardware Hardware x 1PC x 1PC x 1PC x 2PCS x 1PC x 1PC Wall Wall Before drilling hole into wall, make sure the hole is the same height as the unit.
STEP : 23 Page 19 of 19