Sidewinder High Definition IP Cameras SW720-H.
TABLE OF CONTENTS INFORMATION................................................................................................................................. 3 FCC NOTICE .................................................................................................................................. 3 READ THIS MANUAL.................................................................................................................. 3 PRODUCT WARRANTY AND REPAIR ..............................................
INFORMATION FCC NOTICE This device complies with Part 15 of the FCC Rules. TOLL FREE. 866/gotowti (468-6984) TEL. 805/339-9696 FAX. 805/339-0932 Operation is subject to the following two conditions: EMAIL: sales@gotowti.com INTERNET: http://www.gotowti.com 1.) This device may not cause harmful interference. 2.) This device must accept any interference that may be received, including interference that may cause undesired operation.
PRODUCT WARRANTY AND REPAIR PRODUCT WARRANTY We appreciate your purchase of Wireless Technology, Inc. (WTI) security products. We take pride in the quality of our products and have manufactured each new WTI product to exacting quality standards. In normal use, it will provide you with years of satisfactory performance. However, should you experience difficulty; you are protected under the provisions of this warranty.
PRODUCT WARRANTY AND REPAIR REPAIR AUTHORIZATION Please contact Wireless Technology, Inc. (WTI), to obtain a repair authorization number (RA) and provide the following information: 1.) Product Model & Serial Numbers 2.) Date of shipment, purchase order number, sales order number or WTI invoice number. 3.) Details of the defect or malfunction.
PRODUCT WARRANTY AND REPAIR WARNING The Sidewinder series of IP66/IP67 rated cameras provide a fully sealed, moisture free environment for the internal electronic and mechanical components. If the camera housing cover or seals become compromised due to being struck by objects or damaged during handling, the cameras should be taken out of service IMMIDIATELY, so that the camera can be returned to WTI for repair. This will help prevent further EXPENSIVE internal corrosion damage from occurring.
SAFEGUARDS IMPORTANT SAFEGUARDS 1.) Read Instructions. It is important to read all safety and operating instructions before installing or using this equipment. 2.) Retain Instructions. Retain this manual and any supplements for future reference. 3.) Follow Instructions. Follow all instructions herein for use of this equipment. 4.) Heed all warnings. Adhere to all warnings on the equipment, and in this manual. 5.
GENERAL DESCRIPTION The Sidewinder SW720-H264-HD is a pan-tilt-zoom camera system that provides high definition color video in a variety of resolutions, up to 1080p30, over an Ethernet connection, using H.264 or MJPEG video compression. The camera provides 360 degree continuous rotation in both the pan and tilt axes, and provides an optical zoom magnification of 20 times or 30 times.
MODELS AND FEATURES SW720-H.264-HD x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ELECTRIC BRAKES PRESSURIZATION X30 ZOOM BLOCK CAMERA X20 ZOOM BLOCK CAMERA SIDE EGRESS MS 36 INCH AMP UMBILICAL MODEL SW720-H.264-HD SW720-H.264-HD-ENG SW720-H.264-HD30 SW720-H.264-HD30-ENG SW720P-H.264-HD SW720P-H.264-HD-ENG SW720P-H.264-HD30 SW720P-H.264-HD30-ENG SW720HV-H.264-HD SW720HV-H.264-HD-ENG SW720HV-H.264-HD30 SW720HV-H.264-HD30-ENG SW720AMP-H.
INSTALLATION RECOMMENDED TOOLS FOR PROPER INSTALLATION 1) 2) 3) 4) Tie wraps to secure cable runs. Set of open end wrenches including 7/16” for mounting bolts. Cordless power drill for mounting some brackets. Safety cable recommended (prevents camera falling during overhead installations). 5) Self-sealing connector tape to weatherproof all cable connections. INSTALLATION PLANNING 1) The maximum cable length that should be planned for is 100 meters, based on the limit for 10/100Base-T Ethernet connections.
DIMENSIONS AND MOUNTING MECHANICAL DIMENSIONS BOTTOM EGRESS SIDE EGRESS SW720-H.
MOUNTING The Sidewinder SW720-H264-HD camera should normally be mounted in an upright orientation, as shown above. The camera may also be mounted upside down if desired, but a cover of some sort should be placed over the bottom of the camera, extending out to about 6 inches past the camera all around, to prevent debris, dirt or snow and ice from accumulating on the bottom of the camera housing, since the conical shaped profile of the camera will no longer be able to naturally shed material to the sides.
MOUNTING ACCESSORIES WTI manufactures several different mounts for the Sidewinder SW720A that allow the camera to be attached to pole tops, horizontal poles, vertical poles and walls. The Sidewinder SW720-H.264-HD camera is supplied with a 36 inch umbilical cable to allow the cable to be routed through the camera mount before the actual physical installation of the camera. SWWM1 – Wall Mount Option SW720-H.
SWWM1 + SWVPA – Wall Mount with Vertical Pole Adapter SW720-H.
SWPTM1 – Pole Top Mount SW720-H.
SWHPM1 – Horizontal Pole Mount SW720-H.
15-4-1430 – 6”x6”x3/8” Square Mounting Plate SW720-H.
15-4-913 – 6”Round Riser Mounting Base SW720-H.
120VAC MS SIGNAL CONNECTIONS The Sidewinder SW720-H.264-HD is provided with a 36 inch umbilical cable and is available with an 18 pin MS Style connector at the end. The umbilical cable provides the power and Ethernet data and control signals for the camera. The umbilical cable exits through the bottom of the camera housing. These connector pin outs are for all SW720H.264-HD models except for 24VAC and AMP connector models.
24 VAC MS STYLE SIGNAL CONNECTIONS SW720-24-H.264-HD - Side egress 18 Pin MS style connector SW720-24-H.264-HD30 - Side egress 18 Pin MS style connector SW720P-24-H.
120VAC AMP STYLE SIGNAL CONNECTIONS SW720AMP-H.
SIGNAL DESCRIPTIONS 120VAC LINE CONNECTIONS The AC Line connections should be connected to an AC mains source with a voltage of 85VAC to 265V AC, operating at a frequency of 47Hz to 63Hz. The nominal operating voltage is normally 115VAC or 230VAC. The camera draws 50 Watts maximum, which translates to about 0.6 Amps at the worst case low line voltage of 85VAC. We recommend SJOOW cable for these signals.
RJ-45 SERIAL DATA BREAKOUT BOX An RJ-45 Serial Data Breakout Box is available to facilitate legacy installations that utilize the RS-485 signals available on the SW720-H.264-HD series of cameras. The RS485 signals are routed on the two unused pairs in the Ethernet CAT-5e or CAT-6 cable. Note that shielded Ethernet CAT-5e or CAT-6 cable, like Belden 1300A, should be used for these types of legacy installations.
CAMERA ETHERNET PROTOCOLS AND PORTS The PTZ camera control functions and video streaming functions to and from the SW720-H264-SD camera are transmitted over a 100Base-TX Ethernet connection using specific Ethernet ports are assigned for each of the various functions and protocols. DEFAULT IP ADDRESS The SW720-H264-SD camera default IP Address is: 192.168.1.251 DEFAULT PORT ADDRESSES The following ports are provided for the various services available.
Default Transport Notes (Stream 1) random SSM) static group address may also be configured. Multicast Video RTP/RTCP (Stream 2) UDP Multicast (group address random SSM) Protocol Default Port 18890/18891 Only if video stream 2 is set up for Multicast transport. A static group address may also be configured. CAMERA PROTOCOL SUPPORT The SW720-H264-SD camera supports COHU, Pelco D, WTI, NTCIP, Web/ONVIF and other protocols through the RS-485 data connections.
SURGE PROTECTION AND PRESSURIZATION SURGE PROTECTION The SW720-H264-HD camera provides internal surge protection for all of the power, data and video signals. 1.) The AC line power connections are provided with 275 volt 135 Joule MOV surge arrestors rated for 6000 Amp pulses. A 3A SMT fuse is included in the primary circuit to prevent catastrophic printed circuit board damage in the case of gross AC line input overloads. 2.
SPECIFICATIONS X30 ZOOM IMAGE SENSOR AND LENS Image Sensor Type Solid State EXMOR CMOS Progressive Scan Image Sensor Size 1/2.8” inch type Pixel Resolution 2144 horizontal x 1588 vertical (total) – 2096(H) x 1561(V) viewable Video Output Format HD: 1080P30 at full resolution Maximum Lens Aperture F1.6 at full wide angle – F4.7 at full telephoto Optical Zoom Range x1 to x30 Focal Length 4.3mm ~ 129mm Digital Zoom Range x1 to x12 with smooth transition from optical to digital Combined Focal Length 4.
Digital Zoom Range Combined Focal Length Optical Zoom Speed Horizontal Angle of View Minimum Focus Distance Electronic Stabilization Auto Focus Manual Focus Speed Shutter Speed Auto Iris AGC Range Minimum Illumination Color Balance Gamma Signal to Noise Ratio Synchronization Features VIDEO ENCODING Video Encoding Video Streams Codec Image Resolution Streaming Mode Image Settings Frame Rate Data Rate Connection Types Video Latency Network Protocol Layers x1 to x12 with smooth transition from optical to d
External Window Coating High temperature vacuum deposited hydrophilic coating to reduce window cleaning maintenance. Internal Window Coating Electrically conductive coating to allow energy saving direct heating of window glass to prevent fogging. Window Heat Control Proportionally controlled closed loop window heater drive circuit with outside temperature sensor unit to provide fog free window operation under all environmental conditions.
Sector Zones Privacy Zones Low Pressure Warning Temperature Warning Program Memory ELECTRICAL AC Line Voltage Power Consumption Analog Video Output Video Transient Protection Control Data Data Transient Protection Control Data Protocol Power interrupt immunity Power transient immunity Interface connector ENVIRONMENTAL Ambient Temp. Limit Humidity Protection Rating Air Contaminants Vibration Shock Water Spray Immunity SW720-H.
Water Immersion Immunity IPx7 - IEC 60529 section 14.2.7 using an immersion depth of 1 meter measured at the bottom of the camera and a duration of 30 minutes. Icing Immunity NEMA 250-2003 section 5.6. Corrosion Immunity NEMA 250-2003 section 5.10 and the procedure specified in ASTM-B117 Marine. EMI Radiation Within the limits set by FCC Regulations 47 CFR Part 15 for Class A devices. MECHANICAL Dimensions Weight Construction 12.6”L x 11.3”H x 9.25”W (32cm x 29cm x 20cm) 14.6 lbs. (6.64 kg.
