Reference Manual
Table Of Contents
- Introduction
- Electrical specifications
- Pinout
- Quick start
- Functional description
- State indication using the LED pins
- Sleep mode
- Identification of a Proteus-III device on the radio
- Connection based data transmission, with or without security
- Unidirectional connectionless data transmission using Beacons
- Energy-efficient distance estimation solutions
- Configure the module for low power consumption
- Start the direct test mode (DTM)
- Using the 2 MBit and LE Coded phy
- Connection setup using LE Coded phy
- Host connection
- The command interface
- Scan for other modules in range
- Setup connections
- Transmit and receive data
- Configuring the module and modifying the device settings
- Manage the device state
- Run the Bluetooth test modes
- Switching GPIOs by remote control
- Other messages
- Message overview
- UserSettings - Module configuration values
- FS_DeviceInfo: Read the chip type and OS version
- FS_FWVersion: Read the firmware version
- FS_MAC: Read the MAC address
- FS_BTMAC: Read the BLE conform MAC address
- FS_SerialNumber: Read the serial number of the module
- RF_DeviceName: Modify the device name
- RF_StaticPasskey: Modify the static passkey
- RF_SecFlags: Modify the security settings
- RF_SecFlagsPerOnly: Modify the security settings (Peripheral only mode)
- RF_ScanFlags: Modify the scan behavior
- RF_BeaconFlags: Interprete the advertising data
- RF_AdvertisingTimeout: Modify the advertising timeout
- RF_AdvertisingFlags: Configure the advertising packet
- RF_ScanFactor: Modify the scan factor
- RF_ScanTiming: Modify the scan timing
- RF_ConnectionTiming: Modify the connection timing
- RF_TXPower: Modify the output power
- RF_SPPBaseUUID: Configure the SPP base UUID
- RF_Appearance: Configure the appearance of the device
- UART_ConfigIndex: Modify the UART speed
- CFG_Flags: Configure the module
- DIS_ManufacturerName: Configure the manufacturer name
- DIS_ModelNumber: Configure the model number
- DIS_SerialNumber: Configure the serial number
- DIS_HWVersion: Configure the HW version
- DIS_SWVersion: Configure the SW version
- DIS_Flags: Configure the device information service
- Timing parameters
- Peripheral only mode
- Remote GPIO control
- Customizing the Proteus-III
- Custom firmware
- Firmware update
- Firmware history
- Design in guide
- Reference design
- Manufacturing information
- Physical dimensions
- Marking
- Bluetooth SIG listing/qualification
- Regulatory compliance information
- Important notes
- Legal notice
- License terms
7.7.11 CMD_GPIO_LOCAL_WRITE_IND
This command indicates that the GPIOs of the remote device have been written by its local
host.
Please note that only the GPIOs are part of this message, that have been
updated successfully. Failed attempts of GPIO updates will not be indicated by
this message.
Format:
Start signal Command Length Block
1
. . . Block
n
CS
0x02 0xA6 2 Bytes x Bytes x Bytes 1 Byte
The Block is of structure as defined in
CMD_GPIO_LOCAL_READ_CNF block structure
.
7.7.11.1 Example: GPIOs of the remote device have been written by its local host
Start signal Command Length Status Block
1
Block
2
CS
0x02 0xA6 0x07 0x00 0x00 0x02 0x01 0x00 0x02 0x02 0x01 0xA1
The GPIOs with GPIO_ID 0x01 (GPIO is low) and 0x02 (GPIO is high) of the radio module
have been written by its local host.
Proteus-III reference manual version 0.11 © November 2019
www.we-online.com/wireless-connectivity 108