Reference Manual
Table Of Contents
- Introduction
- Electrical specifications
- Pinout
- Quick start
- Functional description
- State indication using the LED pins
- Sleep mode
- Identification of a Proteus-III device on the radio
- Connection based data transmission, with or without security
- Unidirectional connectionless data transmission using Beacons
- Energy-efficient distance estimation solutions
- Configure the module for low power consumption
- Start the direct test mode (DTM)
- Using the 2 MBit and LE Coded phy
- Connection setup using LE Coded phy
- Host connection
- The command interface
- Scan for other modules in range
- Setup connections
- Transmit and receive data
- Configuring the module and modifying the device settings
- Manage the device state
- Run the Bluetooth test modes
- Switching GPIOs by remote control
- Other messages
- Message overview
- UserSettings - Module configuration values
- FS_DeviceInfo: Read the chip type and OS version
- FS_FWVersion: Read the firmware version
- FS_MAC: Read the MAC address
- FS_BTMAC: Read the BLE conform MAC address
- FS_SerialNumber: Read the serial number of the module
- RF_DeviceName: Modify the device name
- RF_StaticPasskey: Modify the static passkey
- RF_SecFlags: Modify the security settings
- RF_SecFlagsPerOnly: Modify the security settings (Peripheral only mode)
- RF_ScanFlags: Modify the scan behavior
- RF_BeaconFlags: Interprete the advertising data
- RF_AdvertisingTimeout: Modify the advertising timeout
- RF_AdvertisingFlags: Configure the advertising packet
- RF_ScanFactor: Modify the scan factor
- RF_ScanTiming: Modify the scan timing
- RF_ConnectionTiming: Modify the connection timing
- RF_TXPower: Modify the output power
- RF_SPPBaseUUID: Configure the SPP base UUID
- RF_Appearance: Configure the appearance of the device
- UART_ConfigIndex: Modify the UART speed
- CFG_Flags: Configure the module
- DIS_ManufacturerName: Configure the manufacturer name
- DIS_ModelNumber: Configure the model number
- DIS_SerialNumber: Configure the serial number
- DIS_HWVersion: Configure the HW version
- DIS_SWVersion: Configure the SW version
- DIS_Flags: Configure the device information service
- Timing parameters
- Peripheral only mode
- Remote GPIO control
- Customizing the Proteus-III
- Custom firmware
- Firmware update
- Firmware history
- Design in guide
- Reference design
- Manufacturing information
- Physical dimensions
- Marking
- Bluetooth SIG listing/qualification
- Regulatory compliance information
- Important notes
- Legal notice
- License terms
UART_ConfigIndex
Rate [Baud] Real rate [Baud] Flow control Parity
33 1000000 1000000 yes none
64 1200 1205 no even
65 1200 1205 yes even
66 2400 2396 no even
67 2400 2396 yes even
68 4800 4808 no even
69 4800 4808 yes even
70 9600 9598 no even
71 9600 9598 yes even
72 14400 14414 no even
73 14400 14414 yes even
74 19200 19208 no even
75 19200 19208 yes even
76 28800 28829 no even
77 28800 28829 yes even
78 38400 38462 no even
79 38400 38462 yes even
80 56000 55944 no even
81 56000 55944 yes even
82 57600 57762 no even
83 57600 57762 yes even
84 76800 76923 no even
85 76800 76923 yes even
86 115200 115942 no even
87 115200 115942 yes even
89 230400 231884 yes even
91 250000 250000 yes even
93 460800 470588 yes even
95 921600 941176 yes even
97 1000000 1000000 yes even
After changing the baud rate using the
CMD_SET_REQ
the module restarts us-
ing the new baud rate. Therefore don’t forget to update the baud rate of the
connected host to be able to further use the module’s UART.
Proteus-III reference manual version 0.11 © November 2019
www.we-online.com/wireless-connectivity 146