Reference Manual
Table Of Contents
- Introduction
- Electrical specifications
- Pinout
- Quick start
- Functional description
- State indication using the LED pins
- Sleep mode
- Identification of a Proteus-III device on the radio
- Connection based data transmission, with or without security
- Unidirectional connectionless data transmission using Beacons
- Energy-efficient distance estimation solutions
- Configure the module for low power consumption
- Start the direct test mode (DTM)
- Using the 2 MBit and LE Coded phy
- Connection setup using LE Coded phy
- Host connection
- The command interface
- Scan for other modules in range
- Setup connections
- Transmit and receive data
- Configuring the module and modifying the device settings
- Manage the device state
- Run the Bluetooth test modes
- Switching GPIOs by remote control
- Other messages
- Message overview
- UserSettings - Module configuration values
- FS_DeviceInfo: Read the chip type and OS version
- FS_FWVersion: Read the firmware version
- FS_MAC: Read the MAC address
- FS_BTMAC: Read the BLE conform MAC address
- FS_SerialNumber: Read the serial number of the module
- RF_DeviceName: Modify the device name
- RF_StaticPasskey: Modify the static passkey
- RF_SecFlags: Modify the security settings
- RF_SecFlagsPerOnly: Modify the security settings (Peripheral only mode)
- RF_ScanFlags: Modify the scan behavior
- RF_BeaconFlags: Interprete the advertising data
- RF_AdvertisingTimeout: Modify the advertising timeout
- RF_AdvertisingFlags: Configure the advertising packet
- RF_ScanFactor: Modify the scan factor
- RF_ScanTiming: Modify the scan timing
- RF_ConnectionTiming: Modify the connection timing
- RF_TXPower: Modify the output power
- RF_SPPBaseUUID: Configure the SPP base UUID
- RF_Appearance: Configure the appearance of the device
- UART_ConfigIndex: Modify the UART speed
- CFG_Flags: Configure the module
- DIS_ManufacturerName: Configure the manufacturer name
- DIS_ModelNumber: Configure the model number
- DIS_SerialNumber: Configure the serial number
- DIS_HWVersion: Configure the HW version
- DIS_SWVersion: Configure the SW version
- DIS_Flags: Configure the device information service
- Timing parameters
- Peripheral only mode
- Remote GPIO control
- Customizing the Proteus-III
- Custom firmware
- Firmware update
- Firmware history
- Design in guide
- Reference design
- Manufacturing information
- Physical dimensions
- Marking
- Bluetooth SIG listing/qualification
- Regulatory compliance information
- Important notes
- Legal notice
- License terms
8.23 DIS_ModelNumber: Configure the model number
Settings
index
Designation
Permissible
values
Default value
Permissions
Number
of
Bytes
21
DIS_ModelNumber
See
description
"Default"
read/write
1-64
The user setting
DIS_ModelNumber
specifies the content of the model number field of the De-
vice Information Service. The permissible characters are in the range of 0x20 - 0x7E which
are special characters (see ASCII table), alphabetic characters (a-z and A-Z), numbers (0-9)
and whitespace.
To add the content of the
DIS_ModelNumber
to the DIS profile, please set the
corresponding Bit in the
DIS_Flags
.
8.23.1 Example 1
Set the model number to "Model1" using
CMD_SET_REQ
with settings index 21
Start signal Command Length Settings index
Parameter
CS
0x02 0x11 0x07 0x00 0x15
0x4D 0x6F 0x64 0x65 0x6C
0x31
0x7F
Response
CMD_SET_CNF
: Successfully modified the setting.
Start signal Command | 0x40 Length Status CS
0x02 0x51 0x01 0x00 0x00 0x52
8.23.2 Example 2
Request the model number of the DIS profile using
CMD_GET_REQ
:
Start signal Command Length Settings index CS
0x02 0x10 0x01 0x00 0x15 0x06
Response
CMD_GET_CNF
: Successfully read out the value "Default".
Start signal Command | 0x40 Length Status
Parameter
CS
0x02 0x50 0x08 0x00 0x00
0x44 0x65 0x66 0x61 0x75 0x6C
0x74
0x11
Proteus-III reference manual version 0.11 © November 2019
www.we-online.com/wireless-connectivity 152