Reference Manual
Table Of Contents
- Introduction
- Electrical specifications
- Pinout
- Quick start
- Functional description
- State indication using the LED pins
- Sleep mode
- Identification of a Proteus-III device on the radio
- Connection based data transmission, with or without security
- Unidirectional connectionless data transmission using Beacons
- Energy-efficient distance estimation solutions
- Configure the module for low power consumption
- Start the direct test mode (DTM)
- Using the 2 MBit and LE Coded phy
- Connection setup using LE Coded phy
- Host connection
- The command interface
- Scan for other modules in range
- Setup connections
- Transmit and receive data
- Configuring the module and modifying the device settings
- Manage the device state
- Run the Bluetooth test modes
- Switching GPIOs by remote control
- Other messages
- Message overview
- UserSettings - Module configuration values
- FS_DeviceInfo: Read the chip type and OS version
- FS_FWVersion: Read the firmware version
- FS_MAC: Read the MAC address
- FS_BTMAC: Read the BLE conform MAC address
- FS_SerialNumber: Read the serial number of the module
- RF_DeviceName: Modify the device name
- RF_StaticPasskey: Modify the static passkey
- RF_SecFlags: Modify the security settings
- RF_SecFlagsPerOnly: Modify the security settings (Peripheral only mode)
- RF_ScanFlags: Modify the scan behavior
- RF_BeaconFlags: Interprete the advertising data
- RF_AdvertisingTimeout: Modify the advertising timeout
- RF_AdvertisingFlags: Configure the advertising packet
- RF_ScanFactor: Modify the scan factor
- RF_ScanTiming: Modify the scan timing
- RF_ConnectionTiming: Modify the connection timing
- RF_TXPower: Modify the output power
- RF_SPPBaseUUID: Configure the SPP base UUID
- RF_Appearance: Configure the appearance of the device
- UART_ConfigIndex: Modify the UART speed
- CFG_Flags: Configure the module
- DIS_ManufacturerName: Configure the manufacturer name
- DIS_ModelNumber: Configure the model number
- DIS_SerialNumber: Configure the serial number
- DIS_HWVersion: Configure the HW version
- DIS_SWVersion: Configure the SW version
- DIS_Flags: Configure the device information service
- Timing parameters
- Peripheral only mode
- Remote GPIO control
- Customizing the Proteus-III
- Custom firmware
- Firmware update
- Firmware history
- Design in guide
- Reference design
- Manufacturing information
- Physical dimensions
- Marking
- Bluetooth SIG listing/qualification
- Regulatory compliance information
- Important notes
- Legal notice
- License terms
• A label must be affixed to the outside of the host product with the following statements:
This device contains FCCID: R7T1101102
This equipment contains equipment certified under ICID: 5136A-1101102
• The final host / module combination may also need to be evaluated against the FC-
C Part 15B criteria for unintentional radiators in order to be properly authorized for
operation as a Part 15 digital device.
• If the final host / module combination is intended for use as a portable device (see
classifications below) the host manufacturer is responsible for separate approvals for
the SAR requirements from FCC Part 2.1093 and RSS-102.
OEM requirements:
The OEM must ensure that the following conditions are met.
• The Proteus-III will be used at a distance of at least 10 mm.
• End users of products, which contain the module, must not have the ability to alter
the firmware that governs the operation of the module. The agency grant is valid only
when the module is incorporated into a final product by OEM integrators.
• The end-user must not be provided with instructions to remove, adjust or install the
module.
• The Original Equipment Manufacturer (OEM) must ensure that FCC labeling require-
ments are met. This includes a clearly visible label on the outside of the final product.
Attaching a label to a removable portion of the final product, such as a battery cover,
is not permitted.
• The label must include the following text:
Contains FCC ID: R7T1101102
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(i.) this device may not cause harmful interference and
(ii.) this device must accept any interference received, including interference that may
cause undesired operation.
When the device is so small or for such use that it is not practicable to place the s-
tatement above on it, the information required by this paragraph shall be placed in a
prominent location in the instruction manual or pamphlet supplied to the user or, alter-
natively, shall be placed on the container in which the device is marketed. However,
the FCC identifier or the unique identifier, as appropriate, must be displayed on the
device.
• The user manual for the end product must also contain the text given above.
– Changes or modifications not expressly approved could void the user’s authority
to operate the equipment.
– The OEM must ensure that timing requirements according to 47 CFR 15.231(a-c)
are met.
– The OEM must sign the OEM Modular Approval Agreement.
– The module must be used with only the following approved antenna(s).
Proteus-III reference manual version 0.11 © November 2019
www.we-online.com/wireless-connectivity 208