Reference Manual
Table Of Contents
- Introduction
- Electrical specifications
- Pinout
- Quick start
- Functional description
- State indication using the LED pins
- Sleep mode
- Identification of a Proteus-III device on the radio
- Connection based data transmission, with or without security
- Unidirectional connectionless data transmission using Beacons
- Energy-efficient distance estimation solutions
- Configure the module for low power consumption
- Start the direct test mode (DTM)
- Using the 2 MBit and LE Coded phy
- Connection setup using LE Coded phy
- Host connection
- The command interface
- Scan for other modules in range
- Setup connections
- Transmit and receive data
- Configuring the module and modifying the device settings
- Manage the device state
- Run the Bluetooth test modes
- Switching GPIOs by remote control
- Other messages
- Message overview
- UserSettings - Module configuration values
- FS_DeviceInfo: Read the chip type and OS version
- FS_FWVersion: Read the firmware version
- FS_MAC: Read the MAC address
- FS_BTMAC: Read the BLE conform MAC address
- FS_SerialNumber: Read the serial number of the module
- RF_DeviceName: Modify the device name
- RF_StaticPasskey: Modify the static passkey
- RF_SecFlags: Modify the security settings
- RF_SecFlagsPerOnly: Modify the security settings (Peripheral only mode)
- RF_ScanFlags: Modify the scan behavior
- RF_BeaconFlags: Interprete the advertising data
- RF_AdvertisingTimeout: Modify the advertising timeout
- RF_AdvertisingFlags: Configure the advertising packet
- RF_ScanFactor: Modify the scan factor
- RF_ScanTiming: Modify the scan timing
- RF_ConnectionTiming: Modify the connection timing
- RF_TXPower: Modify the output power
- RF_SPPBaseUUID: Configure the SPP base UUID
- RF_Appearance: Configure the appearance of the device
- UART_ConfigIndex: Modify the UART speed
- CFG_Flags: Configure the module
- DIS_ManufacturerName: Configure the manufacturer name
- DIS_ModelNumber: Configure the model number
- DIS_SerialNumber: Configure the serial number
- DIS_HWVersion: Configure the HW version
- DIS_SWVersion: Configure the SW version
- DIS_Flags: Configure the device information service
- Timing parameters
- Peripheral only mode
- Remote GPIO control
- Customizing the Proteus-III
- Custom firmware
- Firmware update
- Firmware history
- Design in guide
- Reference design
- Manufacturing information
- Physical dimensions
- Marking
- Bluetooth SIG listing/qualification
- Regulatory compliance information
- Important notes
- Legal notice
- License terms
No µC Pin Designation I/O Description
16 P0.12 /CTS Input
/CTS signal, if flow control is enabled. Using
internal pull down
1
, otherwise. Do not connect
if not needed.
17 P0.03 WAKE_UP Input
Wake-up will allow leaving the system-off mode
or re-enabling the UART. Uses internal pull up
resistor
1
. Do not connect if not needed.
18 GND Supply Ground
B1 P0.09/NFC1
2
B1 GPIO
Pin for remote GPIO access. Do not connect, if
not needed.
B2 P0.10/NFC2
2
B2 GPIO
Pin for remote GPIO access. Do not connect, if
not needed.
B3 P0.23 B3 GPIO
Pin for remote GPIO access. Do not connect, if
not needed.
B4 P1.00 B4 GPIO
Pin for remote GPIO access. Do not connect, if
not needed.
B5 P0.21 B5 GPIO
Pin for remote GPIO access. Do not connect, if
not needed.
B6 P0.07 B6 GPIO
Pin for remote GPIO access. Do not connect, if
not needed.
Table 8: Pinout, second part
Proteus-III reference manual version 0.11 © November 2019
www.we-online.com/wireless-connectivity 20