Reference Manual
Table Of Contents
- Introduction
- Electrical specifications
- Pinout
- Quick start
- Functional description
- State indication using the LED pins
- Sleep mode
- Identification of a Proteus-III device on the radio
- Connection based data transmission, with or without security
- Unidirectional connectionless data transmission using Beacons
- Energy-efficient distance estimation solutions
- Configure the module for low power consumption
- Start the direct test mode (DTM)
- Using the 2 MBit and LE Coded phy
- Connection setup using LE Coded phy
- Host connection
- The command interface
- Scan for other modules in range
- Setup connections
- Transmit and receive data
- Configuring the module and modifying the device settings
- Manage the device state
- Run the Bluetooth test modes
- Switching GPIOs by remote control
- Other messages
- Message overview
- UserSettings - Module configuration values
- FS_DeviceInfo: Read the chip type and OS version
- FS_FWVersion: Read the firmware version
- FS_MAC: Read the MAC address
- FS_BTMAC: Read the BLE conform MAC address
- FS_SerialNumber: Read the serial number of the module
- RF_DeviceName: Modify the device name
- RF_StaticPasskey: Modify the static passkey
- RF_SecFlags: Modify the security settings
- RF_SecFlagsPerOnly: Modify the security settings (Peripheral only mode)
- RF_ScanFlags: Modify the scan behavior
- RF_BeaconFlags: Interprete the advertising data
- RF_AdvertisingTimeout: Modify the advertising timeout
- RF_AdvertisingFlags: Configure the advertising packet
- RF_ScanFactor: Modify the scan factor
- RF_ScanTiming: Modify the scan timing
- RF_ConnectionTiming: Modify the connection timing
- RF_TXPower: Modify the output power
- RF_SPPBaseUUID: Configure the SPP base UUID
- RF_Appearance: Configure the appearance of the device
- UART_ConfigIndex: Modify the UART speed
- CFG_Flags: Configure the module
- DIS_ManufacturerName: Configure the manufacturer name
- DIS_ModelNumber: Configure the model number
- DIS_SerialNumber: Configure the serial number
- DIS_HWVersion: Configure the HW version
- DIS_SWVersion: Configure the SW version
- DIS_Flags: Configure the device information service
- Timing parameters
- Peripheral only mode
- Remote GPIO control
- Customizing the Proteus-III
- Custom firmware
- Firmware update
- Firmware history
- Design in guide
- Reference design
- Manufacturing information
- Physical dimensions
- Marking
- Bluetooth SIG listing/qualification
- Regulatory compliance information
- Important notes
- Legal notice
- License terms
If TXPower = 0x80, there is no value available.
If Device name length = 0, then there is no device name available.
7.1.3.1 Example 1
Request for the
FS_BTMAC
of the devices found during the last scan.
Start signal Command Length CS
0x02 0x0B 0x00 0x00 0x09
Response:
Start signal
Command
| 0x40
Length Status
#Devices
Payload
CS
0x02
0x4B
0x1E 0x00 0x00 0x02
0x11 0x00 0x00 0xDA
0x18 0x00 0xE2 0x04
0x05 0x4D 0x4F 0x44
0x20 0x31 0x55 0x00
0x00 0xDA 0x18 0x00
0xE5 0x00 0x05 0x4D
0x4F 0x44 0x20 0x32
0x11
During the last scan two devices have been detected:
• Device 1 with
FS_BTMAC
0x11 0x00 0x00 0xDA 0x18 0x00, RSSI value of 0xE2 (-30
dBm), TXPower of 0x04 (=+4 dBm) and device name of length 5 with the value of
0x4D4F442031 ("MOD 1").
• Device 2 with
FS_BTMAC
0x55 0x00 0x00 0xDA 0x18 0x00 and RSSI value of 0xE5 (-27
dBm), TXPower of 0x00 (0 dBm) and device name 0x4D4F442032 ("MOD 2") of length
5.
7.1.4 CMD_RSSI_IND
This telegram indicates the reception of an advertising packet sent by another Proteus-III
module. It can be used to realize a position sensing application. This data can only be
received, when the module is in
ACTION_SCANNING
mode (passive scan is sufficient) and the
corresponding value in the
RF_BeaconFlags
is set.
Besides the
FS_BTMAC
, the RSSI value of the advertising packet and the transmission power
of the sending device are output. Both, the RSSI value and the TX power are in two’s
Proteus-III reference manual version 0.11 © November 2019
www.we-online.com/wireless-connectivity 62