Reference Manual
Table Of Contents
- Introduction
- Electrical specifications
- Pinout
- Quick start
- Functional description
- State indication using the LED pins
- Sleep mode
- Identification of a Proteus-III device on the radio
- Connection based data transmission, with or without security
- Unidirectional connectionless data transmission using Beacons
- Energy-efficient distance estimation solutions
- Configure the module for low power consumption
- Start the direct test mode (DTM)
- Using the 2 MBit and LE Coded phy
- Connection setup using LE Coded phy
- Host connection
- The command interface
- Scan for other modules in range
- Setup connections
- Transmit and receive data
- Configuring the module and modifying the device settings
- Manage the device state
- Run the Bluetooth test modes
- Switching GPIOs by remote control
- Other messages
- Message overview
- UserSettings - Module configuration values
- FS_DeviceInfo: Read the chip type and OS version
- FS_FWVersion: Read the firmware version
- FS_MAC: Read the MAC address
- FS_BTMAC: Read the BLE conform MAC address
- FS_SerialNumber: Read the serial number of the module
- RF_DeviceName: Modify the device name
- RF_StaticPasskey: Modify the static passkey
- RF_SecFlags: Modify the security settings
- RF_SecFlagsPerOnly: Modify the security settings (Peripheral only mode)
- RF_ScanFlags: Modify the scan behavior
- RF_BeaconFlags: Interprete the advertising data
- RF_AdvertisingTimeout: Modify the advertising timeout
- RF_AdvertisingFlags: Configure the advertising packet
- RF_ScanFactor: Modify the scan factor
- RF_ScanTiming: Modify the scan timing
- RF_ConnectionTiming: Modify the connection timing
- RF_TXPower: Modify the output power
- RF_SPPBaseUUID: Configure the SPP base UUID
- RF_Appearance: Configure the appearance of the device
- UART_ConfigIndex: Modify the UART speed
- CFG_Flags: Configure the module
- DIS_ManufacturerName: Configure the manufacturer name
- DIS_ModelNumber: Configure the model number
- DIS_SerialNumber: Configure the serial number
- DIS_HWVersion: Configure the HW version
- DIS_SWVersion: Configure the SW version
- DIS_Flags: Configure the device information service
- Timing parameters
- Peripheral only mode
- Remote GPIO control
- Customizing the Proteus-III
- Custom firmware
- Firmware update
- Firmware history
- Design in guide
- Reference design
- Manufacturing information
- Physical dimensions
- Marking
- Bluetooth SIG listing/qualification
- Regulatory compliance information
- Important notes
- Legal notice
- License terms
Start signal Command | 0x40 Length Status CS
0x02 0x42 0x01 0x00 1 Byte 1 Byte
Status:
0x00: Request received, will go to sleep now
0x01: Operation failed
0xFF: Operation not permitted
Please note that the WAKE_UP pin has a second function. If the mod-
ule is not in
ACTION_SLEEP
mode and the UART was disabled using the
CMD_UARTDISABLE_REQ
, the UART can be re-enabled by applying falling edge,
holding the line low for at least 10ms before applying a rising edge and
holding it high for at least 10ms. In this case the module answers with a
CMD_UARTENABLE_IND
message.
7.5.4 CMD_SLEEP_IND
This indication is send by the module when the
RF_AdvertisingTimeout
has expired without
a connection to the module.
Format:
Start signal Command Length Status CS
0x02 0x82 0x01 0x00 0x00 1 Byte
Status:
0x00: Advertising timeout detected, will go to sleep now
7.5.5 CMD_FACTORYRESET_REQ
This command triggers a factory reset of the module. First, the default User Settings are
restored, then the module is reset.
Please note that also the GPIO configuration specified in chapter
11
is reset to
default.
Format:
Start signal Command Length CS
0x02 0x1C 0x00 0x00 0x1E
Response (
CMD_FACTORYRESET_CNF
):
Proteus-III reference manual version 0.11 © November 2019
www.we-online.com/wireless-connectivity 80