Reference Manual
Table Of Contents
- Introduction
- Electrical specifications
- Pinout
- Quick start
- Functional description
- State indication using the LED pins
- Sleep mode
- Identification of a Proteus-III device on the radio
- Connection based data transmission, with or without security
- Unidirectional connectionless data transmission using Beacons
- Energy-efficient distance estimation solutions
- Configure the module for low power consumption
- Start the direct test mode (DTM)
- Using the 2 MBit and LE Coded phy
- Connection setup using LE Coded phy
- Host connection
- The command interface
- Scan for other modules in range
- Setup connections
- Transmit and receive data
- Configuring the module and modifying the device settings
- Manage the device state
- Run the Bluetooth test modes
- Switching GPIOs by remote control
- Other messages
- Message overview
- UserSettings - Module configuration values
- FS_DeviceInfo: Read the chip type and OS version
- FS_FWVersion: Read the firmware version
- FS_MAC: Read the MAC address
- FS_BTMAC: Read the BLE conform MAC address
- FS_SerialNumber: Read the serial number of the module
- RF_DeviceName: Modify the device name
- RF_StaticPasskey: Modify the static passkey
- RF_SecFlags: Modify the security settings
- RF_SecFlagsPerOnly: Modify the security settings (Peripheral only mode)
- RF_ScanFlags: Modify the scan behavior
- RF_BeaconFlags: Interprete the advertising data
- RF_AdvertisingTimeout: Modify the advertising timeout
- RF_AdvertisingFlags: Configure the advertising packet
- RF_ScanFactor: Modify the scan factor
- RF_ScanTiming: Modify the scan timing
- RF_ConnectionTiming: Modify the connection timing
- RF_TXPower: Modify the output power
- RF_SPPBaseUUID: Configure the SPP base UUID
- RF_Appearance: Configure the appearance of the device
- UART_ConfigIndex: Modify the UART speed
- CFG_Flags: Configure the module
- DIS_ManufacturerName: Configure the manufacturer name
- DIS_ModelNumber: Configure the model number
- DIS_SerialNumber: Configure the serial number
- DIS_HWVersion: Configure the HW version
- DIS_SWVersion: Configure the SW version
- DIS_Flags: Configure the device information service
- Timing parameters
- Peripheral only mode
- Remote GPIO control
- Customizing the Proteus-III
- Custom firmware
- Firmware update
- Firmware history
- Design in guide
- Reference design
- Manufacturing information
- Physical dimensions
- Marking
- Bluetooth SIG listing/qualification
- Regulatory compliance information
- Important notes
- Legal notice
- License terms
7.6.2.3 Example: Transmission, carrier test, channel 0
Start the carrier test on channel 0 (2402MHz). We need to use a vendor specific command:
Start
signal
Command
Length
Command
code
Channel /
Vendor option
Length /
Vendor
command
Payload CS
0x02
0x1E
0x04
0x00
0x02 0x00 0x00
0x03 0x19
Response:
Start signal Command | 0x40 Length Status Result CS
0x02 0x5E 0x03 0x00 0x00 0x00 0x00 0x5F
See the previous example to stop the test again.
7.6.2.4 Example: Set TX power to -4 dBm
Set the TX power to -4dBm (0xFC in two’s complement notation):
Start
signal
Command
Length
Command
code
Channel /
Vendor option
Length /
Vendor
command
Payload CS
0x02
0x1E
0x04
0x00
0x02 0xFC 0x02
0x03 0xE7
Response:
Start signal Command | 0x40 Length Status Result CS
0x02 0x5E 0x03 0x00 0x00 0x00 0x00 0x5F
7.6.2.5 Example: Set PHY to 2MBit mode
Set the phy to 2MBit mode:
Start
signal
Command
Length
Command
code
Channel /
Vendor option
Length /
Vendor
command
Payload CS
0x02
0x1E
0x04
0x00
0x00 0x02 0x02
0x00 0x18
Response:
Proteus-III reference manual version 0.11 © November 2019
www.we-online.com/wireless-connectivity 88