Data Sheet

ManualsBrandsWürth Elektronik ManualsActive ComponentsWürth Elektronik 173010542 DC/DC converter (print) 5 V 1 A 5 W No. of outputs: 1 x

WPMDH1100xx1S / 173010x42

MagI

C Power Module

FDSM – Fixed Step Down Regulator Module

we-online.com Würth Elektronik eiSos GmbH & Co. KG – Data Sheet Rev. 1.0

IMPORTANT NOTES

The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:

1. General Customer Responsibility

Some goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general

suitability for certain application areas. These statements about suitability are based on our knowledge and experience of

typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about

the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is

always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to

investigate and decide whether the device with the specific product characteristics described in the product specification is

valid and suitable for the respective customer application or not. Accordingly, the customer is cautioned to verify that the

datasheet is current before placing orders.

2. Customer Responsibility related to Specific, in particular Safety-Relevant Applications

It has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the

usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range

of the specifications. In certain customer applications requiring a very high level of safety and especially in customer

applications in which the malfunction or failure of an electronic component could endanger human life or health it must be

ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused

to third parties in the event of malfunction or failure of an electronic component.

3. Best Care and Attention

Any product-specific notes, warnings and cautions must be strictly observed.

4. Customer Support for Product Specifications

Some products within the product range may contain substances which are subject to restrictions in certain jurisdictions in

order to serve specific technical requirements. Necessary information is available on request. In this case the field sales

engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.

5. Product R&D

Due to constant product improvement product specifications may change from time to time. As a standard reporting procedure

of the Product Change Notification (PCN) according to the JEDEC-Standard we inform about minor and major changes. In

case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted.

The basic responsibility of the customer as per Section 1 and 2 remains unaffected.

6. Product Life Cycle

Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of

products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard

we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products

within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal

sales person in charge about the current product availability expectancy before or when the product for application design-in

disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the

foregoing for customer-specific products.

7. Property Rights

All the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development

contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer

will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent

that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual

property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components

or services are used.

8. General Terms and Conditions

Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and

Conditions of Würth Elektronik eiSos Group”, last version available at www.we-online.com.