User Manual

11/11
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
Wireless Power Design Kit – Medium Power – 760308MP V1.0
Design Kit Manual
EUDC59-U-004 - Rev. 1.0
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
a) You have unique awareness of the Federal, State and local regulatory requirements (including
but not limited to Food and Drug Administration regulations, if applicable) which affects your
products and which refers to your use (and/or the use of your employees, affiliates, contractors or
designees) of the DESIGN KIT for evaluation, testing and other purposes.
b) You are unlimited and exclusive responsible for the safety of your DESIGN KIT and for the
compliance with all relevant laws and other applicable regulatory requirements. Further you have
to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the DESIGN KIT. You are also responsible to ensure that any
interfaces (electronic and/or mechanical) between the DESIGN KIT and any human body are
designed with suitable isolation and means to safely limit the accessible leakage currents to
minimize the risk of electrical shock hazard.
c) Since the DESIGN KIT is not a completed product, it may not meet all applicable regulatory
and safety compliance standards (such as UL, CSA, VDE, CE, RoHS and WEEE) which may
normally be associated with similar completed products. You assume full responsibility to
determine and/ or assure compliance with any such standards and related certifications as may
be applicable. You have to use reasonable safeguards to ensure
that your use of the DESIGN KIT will not result in any property damage, injury or death, even if
the DESIGN KIT should fail to perform as specified or expected.
Certain Instructions. It is important to handle this DESIGN KIT within WE‘s and ROHM’s
recommended specifications and environmental considerations as described in the Quick Start
Guide and Manual. Surpassing the specified DESIGN KIT classifications (including but not
limited to input and output voltage, current, power, and environmental ranges) may cause
property damage, personal injury or death. If there are questions concerning these classifications
please contact a WE external sales representative before connecting interface electronics
including input power and intended loads. Any loads applied beyond the specified output range
may result in unintended and/or inexact operation and/or possible lasting damage to the DESIGN
KIT and/or interface electronics. Please consult the DESIGN KIT Quick Start Guide and Manual
prior to connecting any load to the DESIGN KIT output. If there is uncertainty regarding the load
specification, please contact a WE or ROHM external sales representative. During normal
operation, some circuit components may have case temperatures greater than 60°C as long as
the input and output are maintained at a normal ambient operating temperature. These
components include but are not limited to linear regulators, switching transistors, pass
transistors, and current sense resistors which can be identified by using the DESIGN KIT
schematic published in the DESIGN KIT Quick Start Guide and Manual.
Please be aware that the devices of the DESIGN KIT may be very warm in case of placing the
measurement test setup close to the DESIGN KIT during normal procedure. Please ensure that
only qualified personnel educated in electronic measurement and diagnostics usually found in
development environments should use these DESIGN KITs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and
hold WE, ROHM, its licensors and their representatives harmless from and against any and all
claims, damages, losses, expenses, costs and liabilities (collectively, „Claims“) arising out of or in
connection with any use of the DESIGN KIT that is not in accordance with the terms of the
agreement. This obligation shall apply whether Claims arise under law of tort or contract or any
other legal theory, and even if the DESIGN KIT fails to perform as specified or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for
possible use in safety critical applications (such as life support) where a failure of the WE or
ROHM product would reasonably be expected to cause severe personal injury or death, such as
devices which are classified as FDA Class Ill or similar classification,
Thank you for your accessing to ROHM product information.
More detailed product information and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/