Data Sheet

ManualsBrandsWürth Elektronik ManualsCapacitorsWürth Elektronik WCAP-CSRF High Frequency MLCC Ceramic capacitor 0603 5.6 pF 25 V 1 pc(s)

Dimensions: [mm]

Properties Value Unit Tol.

Length L 0.6 mm ±0.03

Width W 0.3 mm ±0.03

Height H 0.3 mm ±0.03

Pad Dimension Fl 0.15 mm ±0.05

pl1 - Reflow 0.65 mm pl2 - Reflow 0.23 mm fw - Reflow 0.3 mm

Recommended Land Pattern: [mm]

pl2

pl1

Schematic:

Properties Test conditions Value Unit Tol.

Capacitance C

1 ±0.2 V

RMS

, 1 MHz ±10% @25 °

5.6 pF

±0.25pF

Rated Voltage U

(DC)

max.

Q-Factor Q

1 ±0.2 V

RMS

, 1 MHz ±10% @25 °

512 min.

Insulation

Resistance

ISO

Apply U

for 120 s max. 10 GΩ min.

Electrical Properties:

Precondition for Class II MLCC measurement: Apply a preheat treatment @150 ±10 °C for 1 hour.

The measurement should be applied after 24 ±2 hrs the part was stored under ambient conditions.

There is not any precondition necessary for Class I MLCC.

Radio Frequency MLCC

Ceramic Type NP0 Class I

Temperature Coefficient ± 30 ppm max.

Storage Conditions (in original

packaging)

5-35 °C, < 75% RH

Operating Temperature -55 up to +125 °C

Dielectric Strength 5 sec. @250 % U

; Charge & Discharge Current <50 mA

FIT according to separate documentation

Component conform to REACh and RoHS requirements and standards

General Information:

Würth Elektronik eiSos GmbH & Co. KG

EMC & Inductive Solutions

Max-Eyth-Str. 1

74638 Waldenburg

Germany

Tel. +49 (0) 79 42 945 - 0

www.we-online.com

eiSos@we-online.com

CREATED CHECKED GENERAL TOLERANCE PROJECTION

METHOD

KaS PSL DIN ISO 2768-1m

DESCRIPTION TECHNICAL REFERENCE

WCAP-CSRF High Frequency

MLCC

NP002015R6C025DFCT1R000

ORDER CODE

885392004009

SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

0201

001.000 Valid 2018-11-12 eiCap 1/7

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH

& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety

must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.

Summary of content (7 pages)

PAGE 1
Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: Properties pl1 pl2 fw Fl Test conditions Capacitance C Rated Voltage UR Q-Factor Q Insulation Resistance Value Unit Tol. 5.6 pF ±0.25pF 25 V (DC) max. 1 ±0.2 VRMS, 1 MHz ±10% @25 ° C 1 ±0.2 VRMS, 1 MHz ±10% @25 ° C 512 RISO Apply UR for 120 s max. 10 min. GΩ min. Precondition for Class II MLCC measurement: Apply a preheat treatment @150 ±10 °C for 1 hour.
PAGE 2
Mechanical Properties: Properties Adhesive Strength of Termination Definition 0201 10 ±1 sec; 2 N 0402 10 ±1 sec; 5 N Vibration Resistance Resistance to Solder Heat all 3 directions, 2 hours each @ 10 - 55 Hz/ min., amplitude 0.75 mm or 10 g Specific Refer to Soldering Profile Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.
PAGE 3
Packaging Specification - Tape and Reel: [mm] P0 A W3 P2 T (=K0) W1 close to center E1 D0 W F A N D B B0 E2 C Top Cover Tape A0 P1 W2 T1 T1 A Feeding direction End Start Carrier Tape detail B B Cover Tape Top Cover Tape Chip Cavity Sprocket Hole Embossment No Component min. 160mm Components Cover Tape min. 400mm Tolerance Tape width packaging is reffered to the international standard IEC 60286-3:2013 Tape Type 1a A0 (mm) typ. 0,40 B0 (mm) typ.
PAGE 4
Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max TC –5°C Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) Ts min 60 - 120 seconds 3 °C/ second max.
PAGE 5
Cautions and Warnings: Operating climatic conditions: The following conditions apply to all goods within the product series of MLCCs of Würth Elektronik eiSos GmbH & Co. KG: • Do not exceed the lower nor the upper specified temperature under no circumstances. • Be aware that the specified capacitance tolerance is only valid at the date of delivery. • Do not use the capacitors under high humidity, high temperature nor under high or low atmospheric pressure which may affect capacitors reliability.
PAGE 6
Soldering: • The solder profile must comply with the Würth Elektronik technical soldering specification. All other profiles will void the warranty. • All other soldering methods are at the customer’s own risk. • Strong forces which may affect the coplanarity of the component’s electrical connection with the PCB (i.e. pins), can damage the part, resulting in avoid of the warranty.
PAGE 7
Important Notes 6. Product Life Cycle The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG: Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance.