ZeroDelay Full-HD digital video transmission system NEXG1 T USER MANUAL Wuxi R2TECKCo.,Ltd.
无锡人人行拍网络科技有限公司 Content 1. Easy way to start the device ................................................................................................................... 1 1.1 Operating steps and instructions........................................................................................................ 1 2. Specification .............................................................................................................................................. 2 3. Introduction .................
无锡人人行拍网络科技有限公司 1. Easy way to start the device 1.1 Operating steps and instructions 1.1.1Transmitter Install the antennas. Install the camera. Connect transmitter to the power. There should be below instructions if the transmitter works well. After 15 seconds of power on, the WORK light will display the breathing effect, and the WORK light will loop from on to off on display. CAM light turn-on. LINK light turn-on if the transmitterconnect to receiver.
无锡人人行拍网络科技有限公司 2. Specification Here list the detailed specification about NEXG1 T , as shown in Table 2.1.1. Table 2.1.1 List of specification Function specification Communication distance (outdoor, no obstruction) ≥400m Effective Radiated Power（EIRP） >10mw Receiving sensitivity -95dbm±2dbm Operating frequency 5200MHz Physics specification Operating Temperature -10~60℃ Storage Temperature -20~50℃ Size (Include shell, no antenna) L.70mm×W. 36 mm×H.
无锡人人行拍网络科技有限公司 3. Introduction 3.1 Disclaimer Thanks for purchasing the NEXG1 T from Wuxi R2TECK. Everyone need to read and understand this disclaimer before using the NEXG1 T. You are supposed to be accepted the disclaimer once the product is started to use. Please comply with the installation and using process indicated in this use manual. Wuxi R2TECK w ill not be r esponsible f or t he c onsequence of t he i mproper us e, i mproper i nstall, i mproper modify.
无锡人人行拍网络科技有限公司 NEXG1 T should not work when it is wet. Have to make sure it is dry when you use it. NEXG1 T is the high precise product, it is forbidden to beat and clash. Product life time is 2 years, quality warranty is 1 year. Manufacture and dea ler ar e r esponsible f or t he pr oduct m aintenance, w ithout t he authorization, please don't fix the product and don't modify the product.
无锡人人行拍网络科技有限公司 4. Module Port definition 4.1 port 4.1.1 Back side port Figure 4.1.1.1 schematic diagram of back side port [1]: Camera port: For connect the camera. 4.1.2 Side 1 port Figure 4.1.2.1 schematic diagram of side 1 port [1]: Work light, For monitoring the g transmitter operating status. Light status Description Operation Flash regularly Transmitter works well NA Transmitter does not work Connect t he system t o t he power agai n, or c ontact with the customer service.
无锡人人行拍网络科技有限公司 Turn-off Does not connect with camera Check whether the camera is well connected. 4.1.3 Side 2 port Figure 4.1.3.1 schematic diagram of side 2 port [1]: Bind button, For bind the transmitter and receiver. (Both the transmitter and receiver are required to operate simultaneously). Press the button more than 5 seconds, 3 lights (WORL, LINK, CAM) are all turn-off, then 3 lights flash one by one, when the LED light works well that means they are well binded. This may take 2 minutes.
无锡人人行拍网络科技有限公司 5. Contact info Thanks for p urchasing o ur dev ice again. I f y ou have any s uggestion or n eed t echnical s upport, please visit our website or send us the email, also welcome to call us. Wuxi R2TECK Co., Ltd Address：Room307,Building of Cetus,Wuxi software park,111th Linghuavenue,new district ,Wuxi city,Jiangsu Province P.C.：214000 Tel：0510-81012344 Fax：0510-81012344 Web：http://www.gor2teck.com Email：sales1@gor2teck.
无锡人人行拍网络科技有限公司 FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
