USER MANUAL ROBOTIC POOL CLEANER RoadRunner Plus Model: HJ3172P READ AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE Thank you for purchasing Winny® Robotic Pool Cleaner. Please read through the entire manual before using your new robotic pool cleaner. We are not held liable for any loss or injury caused by improper use. If you encounter a problem with your Winny® product, please contact your local dealer for customer services.
LIMITED WARRANTY Winny®, owned by TIANJIN WANGYUAN ENVIRONMENTAL PROTECTION AND TECHNOLOGY CO LTD makes products at the best quality we are able to offer. All Winny® products have been inspected against defects in materials and workmanship prior to leaving factory. Winny® is happy to offer warranty for the repair or replacement of pool products for one (1) year only for battery, motor and PCB from the date of purchase. The provisions of this Limited Warranty only apply to the original purchaser.
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS Failure to comply with the following cautions could cause damage to pool cleaner or personal loss and injury. 1. The cleaner must be operated as specified. 2. To reduce the risk of injury, do not permit children to operate this cleaner. 3. Do not let anyone, especially small children, ride on the cleaner or paly the cleaner as a toy. 4. Do not use the cleaner in your pool if the water temperature is above 35℃ (95℉) or below 10℃ (50℉). 5.
Contents LIMITED WARRANTY.......................................................................................................................... 1 IMPORTANT SAFETY INSTRUCTIONS................................................................................................. 2 Section 1. Introduction...................................................................................................................... 4 Section 3. Product Diagram...............................................................
Section 1. Introduction The robotic pool cleaner HJ3172 Plus is a new type of highly efficient and energy-saving swimming pool cleaning robot. It cleans the pool walls and bottom automatically without replacing the pool water. It is totally environmental-friendly. For safe operation, the cleaner is powered by a rechargeable lithium battery (12.1V, 8.8Ah). Section 2.
Section 4. Specifications Model HJ3172P Rated input voltage of charger 100VAC-240VAC Rated input frequency of charger 50Hz/60Hz Maximum charging voltage 12.6VAC Charging current 1.8A Battery runtime max. 90min Battery capacity 8800mAh Maximum cleaning surface 150m² Maximum pool depth 180μm Filter density 180μm Running speed max. 11m/min (appr. 36ft/min) Running speed max. 11m/min (appr.
Section 5. Operating Instructions 5.1 Power button and indicator ② Indicator ① Power button Item ① Function Switch to power on/off Description Push the button to ON to power on the cleaner; Push the button to OFF to power off the cleaner 1. Blue light is steady on: power on 2. Blue light flashes: the cleaner is working 3. Purple light flashes: Bluetooth connection ② Indicator 4. Yellow light flashes: low battery and start to self-parking 5. Yellow light is steady on: self-parking finished 6.
sure to empty the inside air in order to make the robot work well), then the cleaner can immerse into the pool floor. 5.3 Let it clean The robotic cleaner shall run around the pool floor and wall and vacuum the debris automatically for about 90 minutes until it runs out of battery and stops. 5.4 Retrieve the cleaner The cleaner will move to pool edge when finish working, then use the hook to lift it out of the pool. Note: Attach the retrieving hook to a standard 1¼ inch diameter pool pole (not included).
8 5.5 Filter cleaning 5.5.1 Open the top cover: Put the robot aside the pool and open the top cover (Figure 4-1), the filter basket is located as show in Figure 4-2. Figure 4-1 Figure 4-2 5.5.2 Take out the filter basket (Figure 4-3) Figure 4-3 5.5.3 Wash filter basket (Figure 4-4) 5.5.
5.6 Charge the battery 5.6.1 Remove the cleaner from the pool ① Power off (no indictor flashes) the cleaner ② Attach the charging connector to the charging socket. The indicator lamp on the charger shall turn red when charging. It should turn green once fully charged. Charging socket LED Indicator Red - Charging in Progress Green - Fully Charged Note: Charge the cleaner indoor and at least 3m (appr. 10ft) from the edge of the pool for charging. 5.6.
Section 6. Smartphone Control 6.1 Initial operation 1. Make sure Bluetooth is active on your smartphone and download and activate the WYRobot app (Get access to Bluetooth and location). 2. Push the power button forward, then bule light is on. 3. Push the power button backward and forward in 5 seconds, then purple light flashes. 4. Click on the search button. The app searches for and displays the serial number of the nearest Winny robot. Figure 6-1 5.
Figure 6-2 7. Push the power button backward to finish the set-up. 8. Power on the cleaner. 9. Synchronize the data to Winny robot after set-up and enter the dashboard interface. Hereafter the program runs every time, you will enter the dashboard interface. You can view and modify the settings.
10.
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
