Installation guide

ManualsBrandsWyreStorm Digital Integrity ManualsComputer equipmentNetwork HD Pro

™

Box Contents

The following items are included in the HC-250 box:

• HC-250 Controller

• AC power cord

• IR emitters (4)

• Universal Television Mounting Plate

• Screws (4)

Accessories Available for Purchase

• Rack Mount Kit (C4-1URMK1B-B or C4-

1URMK2B-B)

• Serial Cable Kit (C4-CBL3.5MM-DB9)

Warnings

WARNING! To reduce the risk of electrical

shock, do not expose this apparatus to rain or

moisture.

AVERTISSEMENT! Pour réduire le risque de

choc électrique, n’exposez pas cet appareil à la

pluie ou à l’humidité.

CAUTION: In an over-current condition on

USB or contact output the software disables

the output and then blinks the power LED for

10 seconds. When a USB overcurrent fault is

detected, you will see the power light blink the

LED ﬁve (5) times per second, and then when

a contact overcurrent fault is detected, you will

see the power light blink the LED 12 times a

second. After the 10-second blinking period is

over the over-current circuit will be re-enabled.

If the over-current condition remains, then the

same sequence will repeat itself.

ATTENTION : Dans une condition de

surintensité sur USB ou sortie de contact le

logiciel désactive sortie, puis le DEL Power

clignote pendant 10 secondes. Quand une

erreur de condition de surintensité sur USB

est détectée, vous verrez le DEL Power

clignoté le DEL (5) fois par seconde et puis

quand un défaut de condition de surintensité

sur contact est détecté, vous verrez le DEL

clignoté 12 fois par seconde. Après la période

de 10 secondes de clignotement, le circuit de

sur-courant sera réactivé. Si la condition de

Supported Model

• C4-HC250-BL – HC-250 Controller, Black

Introduction

The Control4® HC-250 Controller (HC-250) provides

ways to control lights, home theaters, distributed

audio and video systems, and other devices

controlled by Infrared (IR), IP, Serial, Contact, or Relay

connections. The Controller has a fast processor,

built-in WiFi, HDMI for audio and video, improved

ZigBee radio, and is perfect for smaller systems!

The HC-250 also provides extensive media

management for audio and video content: CDs,

DVDs, and Blu-ray Discs, or digital media stored on

connected devices. Use an external storage device

with USB or NAS connectivity which supports multi-

zone audio capabilities, sending music to various

rooms throughout the home. The HC-250 ﬁts easily

behind a TV, stacked with AV devices, or mounted on

a rack using the Rack Mount Kit (sold separately).

After you install and conﬁgure the HC-250 (using the

Composer Pro software) along with other system

components, your customers can control their

system using the On-Screen Navigator, MyHome

apps, System Remote Controls, Touch Screens, or

any other Control4-supported interface devices (sold

separately).

HC-250 Controller

Installation Guide

Summary of content (6 pages)

PAGE 1
™ Box Contents The following items are included in the HC-250 box: • HC-250 Controller HC-250 Controller Installation Guide • AC power cord • IR emitters (4) • Universal Television Mounting Plate • Screws (4) Accessories Available for Purchase • Rack Mount Kit (C4-1URMK1B-B or C41URMK2B-B) • Serial Cable Kit (C4-CBL3.5MM-DB9) Warnings Supported Model WARNING! To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture.
PAGE 2
™ HC-250 Controller Installation Guide surintensité reste donc la même, la séquence se répète. For more information, refer to the Products or Documentation pages at www.control4.com. Requirements and Specifications Power Requirements 100-240 VAC, 60/50 Hz, 0.25 A MAX. Power limits: 30W maximum, 10W minimum. PoE requirement: 13W. IR: <100 mW or 20mA of current.
PAGE 3
identify the device in Composer Pro. Controller has been identified in a Control4 9 Composer project and is communicating with 4 5 IR and Serial Outs (4). 3.5 mm jacks for up to Director. four (4) IR emiiters or for a combination of IR Power LED. The Blue LED indicates that AC or emitters and serial devices. Ports 1 and 2 can PoE power is present. The Controller turns on be configured independently for serial control, immediately after power is applied to it. e.g.
PAGE 4
into an electrical outlet. If you are powering the Controller using PoE, you can skip this step. 5 Connect system devices. Attach the devices as described in “Connect the Devices.” 6 Mount the HC-250 1 Use the four (4) screws (provided) to attach the mounting plate to the bottom of the Controller. Set up any external storage devices as described Ensure that the narrow end of the slots is on top in “Setting Up External Storage Devices” in this document.
PAGE 5
• IR Emitters • IR Blaster Troubleshooting Factory Restore Button IR Emitters CAUTION! This action deletes the Composer 1 Plug the 3.5 mm connector end of one of the four project. (4) IR stick-on emitters provided into an IR Out 2 port on the HC-250.
PAGE 6
Warranty Go to http://www.control4.com/warranty for details. About This Document Part number: 200-00240, Rev. B 04/12/2012 control4.com | 6 ™ ©2012 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners.