Instruction manual

29
Technical Support: [e-mail] US: [phone] EU: [phone]
the camera at the remote control when pressing a button.
The remote transmitter can be seen flashing to indicate a
signal being sent. Replace batteries if flashing is not seen
on the digital camera screen.
4) UTP Termination Issues – ensure cables and
RJ45 terminations are correct and in good condition at
both transmitter and receiver ends to see if control is
established. If so, a possible re-termination of the cable
could remedy the problem.
5) Are WyreStorm emitters and receivers being
used? The use of third party products/magic eyes may
not be compatible. Always use WyreStorm components
included with your purchase or check compatibility of third
party control systems with your WyreStorm dealer.
6) IR dropout issues - these can be due to exterior
influences emitting infrared radiation that can interrupt IR
signals. Ensure emitters and receivers are away from the
following causes of IR interference.
• Direct sunlight, Fluorescent lighting (on cold start up)
• Halogen lighting
• Plasma screens
If problems persist, swap out the IR emitters and receivers
to rule out faults with the units themselves. Use emitters
you know are fully operational to test working condition.
Reactivate the IR call-back function on your matrix
and swap IR ports on the matrix to rule out a fault with
thematrix or connection ports.
Should IR remain unresponsive, turn off and disconnect
all cables from the matrix and reconnect zones one at a
time to assess if one location in particular is the problem.
If so, run new cables directly to the display – if this fixes
the problem, it is likely that electromagnetic interference /
damage to the cable somewhere along the run is causing
the IR signal to drop out. Investigate and remove EM
interference from the run or replace damaged UTP cable.
Cat5e or 6?
While our equipment is tested and graded to Cat5e
cable standard; tests have shown that better results
are achieved when using Cat6 cable. The lower AWG
(American Wire Gauge) uses thicker copper cores ensure
better signal transfer/Transmission rates. Newly installed
cabling should always conform to Part P Regulation and
BS 7671 (17th Edition), and should be terminated to 568B
standard.
Can I use a single Cat 5e/Cat 6 cable?
HDBaseT technology only requires a single cable; all
features associated with twin cable are supported with
the added benefit of RS232 control and Ethernet on
100m/328ft HDBaseT products, with 70m/230ft HDBaseT
products removing Ethernet passthrough functionality.
How far can the signal travel?
Under perfect transmission conditions our HDBaseT
receivers will operate at 50m, 70m or 100m (@1080p)
depending on the model used. Perfect conditions means
no electrical interference, straight cable runs with no
bends or kinks and no patch panels or wall outlets.
If some of the above are factors in your installation then
signal strength and bandwidth can be compromised. If
a cable run is reaching the upper limit of the receiver’s
capabilities, then the signal can be boosted by way of an
AMP-001-010 as an in-line repeater up to 7 times (490m)
using HDBaseT technology.
What about 3D?
The RX-70-IR-POH, all of our matrix switches and most
of our extender products will pass-through a 3D Blu-ray
signal (frame packing - Blu-Ray & Stereoscopic - satellite/
cable).
How do I control the sources?
All of our HDMI distribution products support IR pass-
through from point-to-point extender sets to AMP and
HDBaseT matrices. Most of the range now supports
wideband IR meaning it is compatible with any IR device
available on the market.
Our PP and HDBaseT matrix range (Cat 5e/Cat6) has IR
pass-through from each of the outputs and has discrete
IR outputs at the switch end, meaning you can have
multiple identical sources yet the IR would be routed only
to the applicable source.
Do I need power at the TV end?
No. Our RX-70-IR-POH HD display adaptors require
no power supply at the TV end. To operate, the PoH
receivers draw the power from an PoH matrix or PoH
Transmitter. NON PoH devices require 5v. It’s important
that these are powered locally and do not receive remote
power from the rack as there can be issues resulting from
voltage drop along the length of cable.
For non-PoH products, our USB to 5v power cables
overcome the problem of having a second mains outlet
behind the TV. These useful leads draw power from
the USB port of the display to power the receiver, this
also means that the receiver is only powered when the
display is on making the system more energy efficient and
TROUBLESHOOTING AND FAQS
23. FAQ