Installation Guide Wyse® V90L/LE Thin Client 1-GB or 2-GB Flash Upgrade Option Kit Issue: 061908 PN: 883884-08L Rev.
ii Copyright Notice © 2008, Wyse Technology Inc. All rights reserved. This manual and the software and firmware described in it are copyrighted. You may not reproduce, transmit, transcribe, store in a retrieval system, or translate into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of this publication without express written permission.
iii Regulatory Compliance for Thin Clients EMC and Safety Requirements Model VX0 thin clients are compliant with the regulatory requirements in the regions listed below. U.S.A. - FCC Part 15 (class B), UL60950 Canada - ICES-003, CAN/CSA-C22 No. 60950 Europe - EN 55022 (class B), EN 61000-3-2 (class A), EN 61000-3-3, EN 55024, EN 90650-1:2000+ALL Australia / New Zealand - AS/NZS CISPR 22 Japan - VCCI CISPR 22 (class B) China - CCC GB9254-1998, GB17625.
iv Device Power Supply For use with external power supply included in the shipping carton, or a certified equivalent model supplied by the manufacturer. Model VX0, Product V90L/LE Thin Clients For use with External Power Supply Model LSE9802A1255 or certified equivalent model supplied by the manufacturer, output rated for minimum 12Vdc, 4.0A. Caution Replace power supply with the same or equivalent type as recommended by the manufacturer.
Contents About This Guide 1 Before You Begin 1 Kit Warranty 1 What’s in the Kit 1 Required Tools and Materials 1 Wyse Technical Support 2 Related Online Resources Available at Wyse Installing the Option Kit 2 Verifying the Thin Client’s Operation 5 2
vi
Installation Guide Wyse® V90L/LE Thin Client 1-GB or 2-GB Flash Upgrade Option Kit About This Guide This guide describes how to install your 1-GB or 2-GB Flash Upgrade Option Kit in a Wyse V90L/LE thin client. This guide is intended for users of Wyse V90L/LE thin clients. Before You Begin This section provides information about kit warranty, kit contents, the tools needed, and accessing Technical Support and related online resources.
2 Warning The flash module may be susceptible to damage by Electro-Static Discharge (ESD). All industry-standard cautions should be followed to avoid ESD. Caution Follow all precautions listed in the Quick Start Guide that came with your thin client for disconnecting and reconnecting the thin client. Wyse Technical Support To access Wyse technical resources, visit AskWyse.com.
3 4. Remove the top cover from the thin client by inserting the tip of a small Flat-Edge Screwdriver just inside the edge of the lock receptacle to make contact with the metal liner that lines the opening. Apply pressure inward and downward on the metal liner while pulling up on the plastic housing until it releases. 5. Carefully remove the existing Flash module from the socket, noting where the connector of the module is located.
4 6. Install the 1-GB or 2-GB flash module into the location of the original module making sure to align the plastic tab of the module’s connector with the notch in the connector on the board. Warning The flash module may be susceptible to damage by Electro-Static Discharge (ESD). All industry-standard cautions should be followed to avoid ESD. 7. Replace the top cover and attach the vertical foot. 8.
5 Verifying the Thin Client’s Operation To verify that the installation kit has been installed properly: 1. From the desktop, click Start | About to open the Client Information window. 2. Verify that the MAC address and Serial Number matches the serial number and MAC address on the thin client. 3. Verify that the Flash Configuration is approximately 977 MB. 4. Click OK to close the Client Information window. The thin client is ready for operation and setup by the Administrator.
Installation Guide Wyse® V90L/LE Thin Client 1-GB or 2-GB Flash Option Kit Issue: 061908 Written and published by: Wyse Technology Inc.
