X-Micro Bluetooth Headset User Manual 1
X-Micro Bluetooth Headset User Manual Copyright Copyright 2003 by X-Micro Technology Corp., All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of X-Micro Technology Corp. Disclaimer X-Micro Technology Corp.
Introduction The X-Micro Bluetooth Headset is a most desirable gadget to connect with your Bluetooth mobile phone cordlessly. By wearing X-Micro Bluetooth Headset, it becomes most effortless for making a call or receiving a call without handling your mobile phone, moreover, makes the communication naturally. The imperceptible Bluetooth connection can be up to 10 meters and doesn’t need line of sight and get rid of annoying cable for good.
Headset profile General Ratio Carrier Frequency : 2.4 ~ 2.480GHz Ratio Performance – Receiver Rx sensitivity < -80 dBm Ratio Performance: CSR BC02 audio Class II Chipset Spread Spectrum FHSS (Frequency Hopping Spread Spectrum) Antenna Chip Antenna Environmental Operating Temperature 0 ~ +55 Dimensions & Weight 92mm(L) x 50mm(W) x 26mm(H); 26g LED Indicator Status Blue: Power on mode; Red: Low power or being charged Blue & Red: Pairing mode Power Spec. 5V / 500mA Battery 3.
Overview of X-Micro Bluetooth Headset ”Volume Up ” Button ”Volume Down ” Button ”Power / Talk / Pairing ” Button Open / Close the microphone The microphone can be closed when the headset doesn’t use. DC Power In Earhook Speaker Microphone Changing the Earhook The X-Micro Bluetooth headset can be worn on either ear. Please carry out the following steps to shift the ear hook for wearing it on the other ear. 1. Carefully remove the earhook from the headset 2.
Turning the Headset ON/OFF To turn your headset ON: Press and hold the power button for 3 seconds, and then the speaker will emit two high tones. When the power is on, the LED in the power button starts to flash blue. (Note: The headset will go to pairing mode if you press and hold the power button for 5 seconds from OFF status) To turn your headset OFF: Press and hold the power button for 3 seconds, and then the speaker will emit two high tones.
Pairing to a Bluetooth Phone What is Bluetooth Pairing? Before using your headset for the first time, you must pair it with a particular Bluetooth cell phone previously. ”Pairing” process creates a unique wireless link between two devices. Once paired, the communication between two devices does not need any authentication or authorization anymore. Please follow the instruction below to pair the headset with a Bluetooth cell phone: 1. Ensure the headset is OFF. 2.
Answering/Ending a Call Answering a Call After being paired with your cell phone, the headset is now ready to receive incoming calls without handling the phone. When there’s an incoming call, both the cell phone and the headset will ring simultaneously. Upon hearing the ring tones through the headset’s speaker you can answer the incoming call by pressing power button and then speaking normally. Ending a Call You can use either of the ways to end a call: 1. Press the headset’s power button to end a call.
Making a Call There are two ways to make calls: 1. Using the phone’s keypad: As general usage, dial the phone number you want to call by pressing the phone’s keypad. You may also hear the dialing tones through the headset. 2. Using the Voice Dialing through the headset: What is voice dialing? Voice dialing is a feature on some Bluetooth phones which allows you make calls by saying the name of the person you want to call. The phone compares your voice with your previous recording (called a voice tag).
Play Audio CD, MP3 1. Prepare your computer Make sure the Bluetooth software is well-installed in your computer and the Bluetooth device is plugged in. What you need with playing music from the computer: I. A Bluetooth Device which supports Bluetooth Headset profile. Ex. X-Micro Bluetooth USB Dongle (Class 2) / (Class 1) II. A Bluetooth software which supports Bluetooth Headset profile. Ex. Widcomm 1.3.2.7 III. A Bluetooth headset which supports Bluetooth Headset profile. Ex.
III. Connect X-Micro Bluetooth Headset. You will see a X-Micro Bluetooth Headset device on the searching windows after the searching mode, a. Select “X-Micro Bluetooth Headset”. b. Click “Connect”. IV. Input the PIN code for the request. a. Click the Bluetooth icon. b. When the “Bluetooth PIN Code Request” window appears, enter “0000” (4 zeros). c. Click “OK”. V. Complete creating a connection shortcut. a. Click “OK” on “My Bluetooth Places” window. b. Click “OK” on “Bluetooth Service” window. VI.
3. Listen to music from X-Micro Bluetooth Headset I. Play Audio CD a. Connect the X-Micro Bluetooth Headset with the computer: - Make sure the headset is power on. - Press the power button 1 time. - Wait for about 3 seconds the headset will reconnect with the computer. b. Put the Audio CD in CD ROM. c. Run “Windows Media Player” d. Play the Audio CD II. Play MP3 a. Connect the X-Micro Bluetooth Headset with the computer: - Make sure headset is power on. - Press the power button 1 time.
Appendix I Button Function Power Button Turn ON/OFF Press the power button for 3 seconds until the blue LED flashes five times. Answer/End calls Press the power button once Pairing When the headset is off, press the power button to turn on and keep it pressed for about 5 se4conds until the LED flashes blue and red alternately. Down/Up Button Volume control / Mute/Unmute Press the UP or DOWN button repeatedly until you reach your desired level.
www.x-micro.
