Installation Sheet

2. Apply a continuous bead of construction sealant around
the backside of the perimeter mounting flange.
(Recommended Sealant: Sikaflex- 201 or other high grade
exterior sealant. Sealant not included)
3. Insert exhaust box into exterior rough opening,
level horizontally and vertically.
4. Pull rear mounting straps taut and mechanically
fasten to framing member.
5. Insert properly sized metal duct(s) into rear duct port
assembly and secure with metal duct tape.
(Duct tape not included)
MODELS: SLIM-F | SEB-F | MDEB-F | DVEB-F | DHEB-F | TVEB-F | THEB-F
2. Apply a continuous bead of construction sealant around
the backside of the perimeter mounting flange.
(Recommended Sealant: Sikaflex- 201 or other high grade
exterior sealant. Sealant not included)
3. Insert exhaust box into exterior rough opening, level
horizontally and vertically.
4. Slide compression plate over back side of cavity box tight
against metal panel. Install clips and mechanically fasten
to create compression.
5. Insert properly sized metal duct(s) into rear duct port
assembly and secure with metal duct tape.
(Duct tape not included)
MODELS: SLIM-FC | SEB-FC | MDEB-FC | DVEB-FC | DHEB-FC
TVEB-FC | THEB-FC
1. Scope of Coverage
This warranty applies to only new exhaust / intake termination cavity boxes
and in-line sleeves manufactured by FSH Industries and installed according
to FSH Industries Instructions.
2. FSH Industries’ Warranty
Limited Ten Year Warranty: The Exhaust / Intake Termination Cavity Boxes
and In-Line Sleeve are warranted to be free from defects in materials and
workmanship under normal use and service for the exhausting of residential
dryer, bathroom and kitchen hood fans and fresh air make up for a period of
ten years from purchase date, subject to the terms, conditions, and limita-
tions described below. Custom colored boxes and or sleeves offer warranty
coverage exclusively for UV protection and colorfastness.
3. What Is Not Covered
A. Exclutions:
The above warranty does not apply:
1. To conditions resulting from a defect in a component or part
which is not part of the FSH Industries exhaust / intake
termination cavity boxes and in-line sleeves.
  2. ToconditionsresultingfromasignicantdeparturefromFSH
Industries’ installation instructions.
3. To conditions resulting from failure to provide reasonable and
necessary maintenance in accordance with FSH Industries’
operating and maintenance instructions.
4. To conditions resulting from any misuse, abuse, neglect,
accident, alterations or force majeure.
5. To normal fading and minor deterioration of exterior surface
resulting from exposure to the elements, except conditions that
do or will affect performance.
B. No Warranty of Performance of the Exhaust Termination
Boxes and In-Line Sleeves:
FSH Industries makes no warranty as to the performance of its
exhaust / intake cavity boxes and in-line sleeves as to any
particular air flow, since this depends on the different type of
devices used and which cannot be controlled.
C. Limitations on Exclusions from Coverage:
The above warranty shall not be considered to be violated or its
coverage in any way reduced by conditions that may
occur in the normal operation of the exhaust / intake termination
cavity boxes and in-line sleeves.
4. Some Things the buyer Must Do
A. Proper Installation:
Installations MUST be preformed according to the installations
included with the product.
B. Routine Maintenance:
Provide reasonable and necessary maintenance in accordance with
FSH Industries’ operating and maintenance instructions.
C. Keeping FSH Industries Informed:
If it appears to you that any warranted component or part is not
functioning properly, promptly notify FSH Industries. Early attention
to a minor problem may help avoid serious problems later.
5. What FSH Industries Will Do
A. Repair or Service:
If a defect in material or workmanship becomes evident during the
warranty period, FSH Industries will repair at its option or replace
the malfunctioning exhaust / intake termination cavity box or in-line
sleeve with a new exhaust / intake termination cavity box or in-line
sleeve of at lease the same quality and within a reasonable time.
B. Who Will Provide Warranty Service?
Service will be provided by FSH Industries’ authorized representative
or distributor in your area. This will ordinarily be the manufacturer’s
representative or distributor from whom you purchased your exhaust
/intake termination cavity box and or in-line sleeve. If there is no
authorized manufacturer’s representative or distributor in your area
then write FSH Industries, LLC. directly at 8022 Providence Rd.
Suite: 500-145 Charlotte, NC 28277 attention Warranty Claims
Department or email us at: [e-mail].
Please provide the model number, date of purchase and the nature
of the defect or problem. To verify that your warranty is still in
effect, you should be prepared to furnish evidence of date of
purchase and evidence that the installation was preformed
accordance to the instructions included with the product.
C. Charges if Replacement is Required (not covered under warranty):
You are responsible for the payment of any cost and expenses of
disassembly, removal and re-installation of the exhaust termination
box or in-line sleeve, and any other incidental services involved.
None of such cost or expenses are covered by this warranty,
and FSH Industries is not liable for any of them.
6. No Other Express Warranties – These Remedies are Exclusive
Unless otherwise explicitly agreed to in writing, it is understood that
this is the only written warranty given by FHS Industries and FSH
Industries neither assumes nor authorizes anyone to assume for it
any other obligations or liability in connection with its products.
IN NO EVENT SHALL FSH INDUSTRIES BE LAIBLE FOR DAMAGE TO
PROPERTY, LOST PROFITS, INJURY TO GOODWILL, OR ANY OTHE
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING
FROM ANY DEFECTIVE EXHAUST / INTAKE TERMINATION CAVITY
BOX OR IN-LINE SLEEVE OR ANY BREACH OF THE EXPRESS
WARANTY, FOR NEGLIGENCE OR OTHERWISE.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so this exclusion or limitation may not apply
toyou.Theabovewarrantygivesyouspeciclegalrights,andyou
mayalso have other rights which vary from state to state.
08/18 XVB/LW510
LIMITED TEN YEAR WARRANTY
Models; SLIM,SEB, MDEB, DVEB, DHEB, THEB, TVEB
2
4
3
5
2
3
4
5
F | SERIES
FC | SERIES
Installation Procedure:
1. Rough opening size requirements
SLIM-F 9.0” 4.6”
SEB-F 8.9” 8.1”
MDEB-F 8.9” 8.1”
DVEB-F 9.0” 13.0”
DHEB-F 13.0” 9.0”
TVEB-F 9.0” 13.0”
THEB-F 13.0” 9.0”
(A) LENGTH (B) WIDTH
A
B
A
B
Installation Procedure:
1. Rough opening size requirements
SLIM-FC 9.0” 4.6”
SEB-FC 8.9” 8.1”
MDEB-FC 8.9” 8.1”
DVEB-FC 9.0” 13.0”
DHEB-FC 13.0” 9.0”
TVEB-FC 9.0” 13.0”
THEB-FC 13.0” 9.0”
(A) LENGTH (B) WIDTH