User's Manual
Manuals
Brands
X2E Manuals
Data Loggers
Data logger
81
82
83
84
85
86
87
88
89
90
Table Of Contents
1 Introduction
1.1 About this user manual
1.2 Validity of the user manual
1.3 Representation conventions
1.4 Pictograms
1.4.1 Meaning of warnings
1.4.2 Structure of warnings
1.5 X2E-Wiki
2 Safety and warranty
2.1 Intended use
2.2 Safety label on the device
2.3 General safety instructions
2.4 Product liability
2.5 Terms of use
2.6 Warranty
2.7 FCC notice
3 Product description
3.1 Identification
3.2 Scope of delivery
3.3 Connections and controls
4 Commissioning
4.1 Unpacking
4.2 Selecting an installation location
4.3 Installing the ML-N4000
4.4 Installing the XorayaSuite
4.5 Connecting the ML-N4000 to the measuring environment
4.5.1 Interfaces
4.5.2 Power supply
4.6 Connecting the ML-N4000 to the PC
4.7 Configuring terminators
4.7.1 4x CAN
5 XorayaSuite
5.1 Starting
5.2 Menu bar
5.2.1 File
5.2.2 Logger
5.2.3 View
5.2.4 Help
5.2.5 Language
5.3 Status bar
5.4 Connecting and disconnecting the ML-N4000
5.4.1 Connecting the ML-N4000
5.4.2 Disconnecting the ML-N4000
5.4.3 Favourites
5.5 Configuration
5.5.1 System configuration
5.5.2 Interface configuration
5.5.3 Signal configuration
5.6 Resetting to factory defaults
5.7 Data recording
5.7.1 Online mode
5.7.2 HDD mode
5.7.3 Log data
5.8 Hdd-Download
5.9 Viewer
5.9.1 Data
5.9.2 Information
5.9.3 Search, filter and export
5.9.4 Graphical output
5.10 Statistic
5.11 Convert
5.12 Firmware-Update
5.13 TK Commandline
5.14 Common elements
5.14.1 Changing the numbering system
5.14.2 Set bits
5.14.3 Export settings
5.14.4 Output formats selection
5.14.5 Signal selection
5.14.6 Signal description settings
5.14.7 Create trigger conditions
5.14.8 Graph View
6 Maintenance
6.1 Safety measures
6.2 Cleaning
6.3 Repair
7 Storage, transport and disposal
7.1 Storage
7.2 Transport
7.3 Disposal
8 Appendix
8.1 Technical data
8.2 ML-N4000 pin assignments
8.2.1 4x CAN
8.2.2 12x Base-T1
8.2.3 Power/trigger/wake
8.3 Cable pin assignments
8.3.1 4x CAN
8.3.2 Power/trigger/wake
8.4 Output formats
8.4.1 X2E-Native
8.4.2 X2E Ascii
8.4.3 Carmen-Journal
8.4.4 Wireshark PCAP
8.4.5 Vector BLF
8.4.6 Vector ASC
8.4.7 XAA for GNLog
8.4.8 DLT-Autosar
8.4.9 System Events
8.4.10 Raw for RS232/RawSocket
8.4.11 CSV for Analog/CCP/PSI5
8.4.12 CSV for Signals
8.4.13 Video Extractor
8.4.14 MDF Export
U
SER
M
ANUAL
X
ORAYA
S
UITE
89
DiagXCP
:
DiagXCP > Se
ttings:
1
Clear all sett
ings
5
Open selection fil
e
2
Edit interface chan
nel
6
Settings
3
Open A2L file
7
Traffic light for t
he bus load
4
Traffic light for t
he EPK check
8
Engine RPM*
* Only for angle-synchronous event channels
1
...
...
87
88
89
90
91
...
...
182
