MODEL XIS100 Integration Dock for iPod® INSTALLATION INSTRUCTIONS 08905180D -1-
DESCRIPTION Xantech's ‘XIS100' docking station is the industry's first iPod docking station designed for the hiresolution television revolution. It features a unique component video output capability that will enable owners of the new 480p video output iPods to see their video in full native resolution on a plasma, LCD, or other compatible TV screen with component video input. The ‘XIS100' features a unique onscreen menu display and control system and is compatible with the latest iPod video technology.
QUICK START STEP 1: Connect the XIS100 to the power supply and use the included A/V cable to connect to a composite video and audio amplifier. The XIS100 is preconfigured for composite video support. Direct the handheld remote control to the XIS100 and press the ‘power’ button. The blue ring indicator light on the XIS100 will light ‘on’. Be sure the remote control has batteries installed.
BASIC CONNECTIONS The XIS100 is ready to be used right out of the box. Simply connect a power supply and determine if composite or component video is required. In all cases, the A/V cable must be used to provide left and right audio connections. In component video applications, the composite end on the A/V cable has no connection.
NOTE 1: The XIS100 is shipped with composite video output selection. To change to component video, first connect the composite video output, then proceed through the ‘settings’ on the on-screen display. In the ‘Settings’ menu, select “TV Out” and then “Component” to set the XIS100 to component video output. Please remember that some iPods do not have a 480p video output, and therefore cannot output video via the XIS100's component outputs.
REMOTE CONTROL BUTTON CONTROL Main Menu Whenever pressing this button, you can go back to the Main Menu. Power With XIS100 in stand-by, pressing and holding this key for 5 seconds will reset all settings of the XIS100. The TV will display a confirmation screen. Press it to power on and off. Select When you decide to select a item, press it to enter or play it.
BASE STATION – FRONT VIEW 1 Dock Well 2 IR Eye 3 Indicator Bar 08905180D BASE STATION Connects to the iPod connector. Gently slide the iPod unit into the vertical connector and verify it is not tilted. Included with the XIS100 is a Dock Well adaptor for all iPod units. Discreetly hidden is a front panel IR eye used to communicate with the XIS100 remote control. Be sure the remote control is pointing directly towards this lens. The indicator bar lights up when the unit is on.
BASE STATION – REAR VIEW 4 Video Format 5 6 IR IN RS232/422 7 8 Component Out A/V Output 9 Power In 08905180D BASE STATION This selector switch is used to select NTSC or PAL format. (See NOTE 2 on Page 6) Modulated IR. Connect to a Xantech IR bus system. Connect to RS232 or RS422 communications devices. Use Xantech RS422 adaptors, sold separately, if needed (See Page 10). To change between 232 and 422, use the on-screen ‘settings’ menu. Component video output to be connected to a display.
SETTINGS MENU NOTE: The XIS100 will retain all its settings until they are changed again. To return the XIS100 to its default settings, place the XIS100 in standby (connected to a power supply, but not turned on). Point the remote towards the XIS100 and press and hold down the “MENU” button on the remote for more than 5 seconds. The XIS100 will acknowledge this reset by indicating so on the TV screen (composite or component output, whichever one that was last selected).
About XIS100: This selection will indicate the firmware version and any additional XIS100 information.
Xantech Limited Warranty (Effective for products sold after July 1, 2006) Xantech Corporation (“Xantech”) warrants to the holder of a valid proof of purchase as the first end-user purchaser (“You”), its products to be free from defects in materials and workmanship for the periods specified below from the date of purchase. This limited warranty extends only to You for product purchased and used in the United States of America.
ADDITIONAL NOTES: THREADED INSERT FOR INSTALLATION OF BASE UNIT IN PUBLIC PLACES: A) Remove the two race track shaped bump-ons from the bottom of the docking station to expose two threaded inserts. B) Use M4x0.7 machine screws (not supplied) to secure the XIS100 base unit in place. C) While screw length will be determined by mounting surface thickness, XIS100’s maximum thread depth is 8mm. CONTROL COMMANDS – RS232 SERIAL STRING COMMANDS See document 08905193 – XIS100 Serial Protocol. Please visit www.