Owner’s Guide Solar MPPT Remote Panel 710-0010
Copyright © 2019 Xantrex LLC. All Rights Reserved. All trademarks are owned by Xantrex LLC and its affiliates.
IMPORTANT SAFETY INFORMATION READ AND SAVE THIS OWNER’S GUIDE FOR FUTURE REFERENCE . Read these instructions carefully and look at the equipment to become familiar with the device before installing, operating, configuring, maintaining, and troubleshooting it. The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
Product Safety Information 1. Before using the remote panel, read all instructions and cautionary markings on the remote panel's components, the batteries, and all appropriate sections of this guide. 2. Use of accessories not recommended or sold by the manufacturer may result in injury to persons, a risk of electric shock, or a risk of fire. 3. The remote panel is designed to be connected to your DC electrical systems.
DANGER HAZARDORFIRE,ELECTRICALSHOCK,EXPLOSION,ORARCFLASH This Xantrex SOLAR MPPT Remote Panel Owner's Guide is in addition to, and incorporates by reference, the relevant product manuals for each product in the power system. After reviewing this guide you must read the relevant product manuals. Unless specified, information on safety, specifications, installation, and operation is as shown in the primary documentation received with the product.
CAUTION EQUIPMENT DAMAGE Do not integrate this remote panel with a residential electrical system. Failure to follow these instructions can result in injury or equipment damage.
End of Life Disposal The Xantrex SOLAR MPPT Remote Panel is designed with environmental awareness and sustainability in mind. At the end of its useful life, the remote panel can be decommissioned and disassembled. Components which can be recycled must be recycled and those that cannot be recycled must be disposed of according to local, regional, or national environmental regulations.
Contents Important Safety Information Product Safety Information End of Life Disposal Materials List Basic Installation Steps Unit Features Remote Panel LCD Display and Function Buttons Status Icons Event Indicators Operation Using the Remote Panel Automatic Status Display Screens Specifications Mounting Template 8 3 4 7 9 9 12 13 15 17 18 23 24 25 975-1013-01-01 Rev A Oct 2019
Materials List The remote panel base package includes the following items: 1 Xantrex SOLAR MPPT Remote Panel 2 Xantrex SOLAR MPPT Remote Panel bezel 2 Owner's Guide 3 Mounting screws (#4 x 3/8" wood screws) 1 2 Menu Up / Set Power 3 4 NOTE: If any of the items are missing, contact Xantrex or any authorized Xantrex dealer for replacement. See Contact Information on page 1. Basic Installation Steps 1. Prepare the tools for installation.
Figure 1 Preparing for mounting 1 2 Menu Up / Set Power 1 Using the mounting template at the end of this guide, mark the positions of the center hole and the mounting holes on the wall where you plan to mount the remote panel. 2 Using a hole saw with a minimum diameter of 3" (76.2mm) and a maximum of 3.5" (88.9mm) and with the center hole marker, cut a circular hole on the wall. Insert the back of the remote panel through the hole.
Figure 2 Wiring connections diagram 1 2 3 4 5 9 7 6 8 10 11 12 1 PV panel 7 Xantrex SOLAR MPPT Remote Panel cable 2 Solar charge controller 8 Pos [+] Battery cable with battery fuse 3 Xantrex SOLAR MPPT Remote Panel 9 Battery 4 DC equipment ground 10 Neg [–] Battery cable 5 Pos [+] PV cable with PV disconnect device 11 DC battery / Chassis ground 6 Neg [–] PV cable 12 Battery temperature sensor (BTS) cable 2. Install the power system.
Unit Features 1 2 Menu Up / Set Power 3 4 5 6 12 1 LCD display 2 MENU button 3 UP / SET button 4 Power [Standby] button 5 Remote port 6 Mounting holes 975-1013-01-01 Rev A Oct 2019
Remote Panel LCD Display and Function Buttons Button Action Description Allows you to: Menu l Short press l l 975-1013-01-01 Rev A Oct 2019 browse devices such as BAT1, PV, and BAT2 browse settings for each device show automatic status display setting 13
Button Action Description Allows you to: l browse PV Array settings l browse BAT1 settings l browse BAT2 settings l configure the temperature unit l configure the battery type Short press Up / Set Long press (5 sec) Power 14 l en/disable automatic status display Short press Turn on the Remote panel screen Long press (5 sec) Turn off the Remote panel screen 975-1013-01-01 Rev A Oct 2019
Status Icons Icon Description Icon Description BAT1 SOC 0~12% BAT2 SOC 0~12% BAT1 SOC 13~35% BAT2 SOC 13~35% BAT1 SOC 36~61% BAT2 SOC 36~61% BAT1 SOC 62~86% BAT2 SOC 62~86% BAT1 SOC 87~100% BAT2 SOC 87~100% BAT1 Charging BAT2 Charging Daytime Nighttime Display BAT1 parameters Display BAT2 parameters PV Panel Display PV parameters 975-1013-01-01 Rev A Oct 2019 15
Icon Description Icon Description BAT1 temperature Battery type Settings (Parameters) Minimum voltage Auto screen cycle Maximum voltage Event 16 975-1013-01-01 Rev A Oct 2019
Event Indicators NOTE: When an event is detected the LED indicators flash and the individual icons on the LCD Display also flash. LCD Icon/s Event Description Over-charging event on BAT1 Over-charging event on BAT2 BAT1 discharged BAT2 discharged Over-temperature event on BAT1 BAT1 charging voltage outside of range BAT2 charging voltage outside of range BAT1 and/or BAT2 batteries are not connected. PV is connected.
Operation Using the Remote Panel To browse different devices and their settings: Power 1. Short press to turn on the panel. Menu 2. Press repeatedly to display each device screen. Power 3. Short press to turn off the panel screen. NOTE: Pressing this button does not turn off the solar charger unit, only the display panel screen.
To enable automatic status display: Power 1. Short press to turn on the panel, if not already on. Menu 2. Press once to display Auto. Up / Set 3. Press and hold for 5 seconds until appears. After 2 seconds each device setting will be displayed in sequence every 2 seconds. See Automatic Status Display Screens on page 23. Menu NOTE: Pressing subsequently will disable automatic status display. To enable it again, perform step 3 again.
To change the temperature unit setting: Power 1. Short press to turn on the panel, if not already on. Menu 2. Press displayed. repeatedly until the BAT1 device screen is Up / Set 3. Press repeatedly until the temperature, the icon, and the icon are displayed. Up / Set 4. Press and hold for 5 seconds until the temperature value changes and flashes to degC (or degF). Menu 5. Press to browse the desired temperature unit (degC or Up / Set degF), then press 20 to confirm your selection.
To change the battery type setting: Power 1. Short press to turn on the panel, if not already on. Menu 2. Press repeatedly until the BAT1 (or BAT2 ) device screen is displayed. Up / Set 3. Press repeatedly until the current battery type, the icon, and the icon are displayed. Up / Set 4. Press and hold type flashes. for 5 seconds until the current battery Menu 5.
To reset the PV Harvest: Power 1. Short press to turn on the panel, if not already on. Menu 2. Press displayed. repeatedly until the PV device screen is Up / Set 3. Press repeatedly until the cumulative PV Harvest status screen is displayed. Menu Up / Set 4. Simultaneously, press and hold buttons for 5 seconds until the PV Harvest value is reset to 0WH.
Automatic Status Display Screens Shows input PV voltage. → → Shows input PV current. → → → → Shows BAT1 maximum voltage. → → 975-1013-01-01 Rev A Oct 2019 → → → → → → Shows BAT2 current. Shows BAT2 maximum voltage. → Shows BAT1 battery temperature. Shows battery 2 (BAT2) voltage. Shows BAT1 Battery type. → → → → Shows BAT1 current. Shows BAT1 minimum voltage. → → → Shows input PV power.
Specifications NOTE: Specifications are subject to change without prior notice. Specifications 24 Solar MPPT Remote Panel Part number 710-0010 Power consumption 10mA/5VDC Minimum power consumption 3mA Operating temperature -20 – 70 °C (-4 – 158 °F) Storage temperature -20 – 70 °C (-4 – 158 °F) IP protection IP20 Unit weight 110 g (0.25 lbs.) Physical dimensions 98 × 98 mm (3.8 × 3.
Mounting Template NOTE: You may tear the next page. 3” (76.2mm) 3.5” (88.9mm) NOTE: Markthe positionsof the center hole and the mounting holeson the wallwhere you plan to mount the remote panel. Use a hole saw with a minimum diameter of 3" (76.2mm) and a maximum of 3.5"(88.9mm) to cut a circular hole on the wall.
This page has no content.
+1-800-670-0707 +1-408-987-6030 customerservice@xantrex.com http://www.xantrex.com/power-products-support/ http://www.xantrex.
