Model # 74303 “Blue Ridge Play” - 4 Leg Swing Set Assembled dimensions are 128" x 93" x 75". Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully assembled. OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE WARNING! Please read this entire instruction and assembly manual completely before proceeding. You must follow all safety instructions while using this equipment.
IMPORTANT INSTRUCTIONS AND WARNINGS WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT AGE LIMIT This product is designed to be used by up to six (6) children between the ages of 3 to 8. Maximum user weight is 100 pounds (45 kg) each with a combined maximum weight of 600 pounds (272kg). The play set is designed for children over three (3) years of age up to (8) years of age. Use by smaller children can result in entrapment.
Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall onto a hard surface can result in serious injury or death to the user.
PLAY SUPERVISION DO NOT allow more than one child to play on the individual swing or slide component at any one time. DO NOT allow children to stand on the slide, swing seats or glide ride. The glide ride is made for only two users at a time. DO NOT allow children to walk too close to moving parts. ALWAYS keep a safe distance to avoid being struck by other children while playing on swings, slides, and glide ride, etc.
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially hazardous to users.
ANCHORING (NOTE:ANCHORS ARE NOT INCLUDED-MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping. You should consult your local contractor to decide the most appropriate way to anchor the equipment in your location.
FRAME LEG 12-5/8” CONCRETE 5” 2” BRICK OR GRAVEL BED Note: The maximum fall height for this product is 4 feet. The minimum ground clearance between the bottom of the suspended plays and the playing or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground clearance. 8” WARNING Please properly anchor the swing set to minimize the risk of injury or death. If the swing set is used without proper anchoring, it may be dangerous and may tilt over.
CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON: Tighten all hardware. Lubricate all metallic moving parts per manufacturer’s instructions. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. Check all moving parts including swing seats and chains for wear, rust or other deterioration. Replace as needed. Check metal parts for rust.
TOOLS NEEDED Please prepare the following tools prior to assembling this equipment. Special Socket Wrench (Included) Hammer (If you intend to install anchor, this is needed) Wrench (Not Included) Flat Head and Philips Head Screwdriver (Not included) Tape Measure (Not included) Wrench (Included) Big Allen Wrench (Included) Medium Allen Wrench (Included) Small Allen Wrench （Not Included) DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.
Part list for main frame assembly A1 LEFT TOP BAR 1 A2 MIDDLE TOP BAR 1 A3 RIGHT TOP BAR 1 A4 TOP SECTION LEG 4 A5 BOTTOM SECTION LEG WITH FOAM 4 A6 CROSS BAR (WITH TWO HOLES) 1 A7 CROSS BAR (WITH FOUR HOLES) 1 C2 END CAP (PRE-ASSEMBLED) 2 Hardware used for main frame assembly B1 BOLT 5/16”*2.5” (8MM*63MM) 12 B2 BOLT 5/16”*2.
Part list for glide ride assembly L1-N TOP SECTION HANGER 2 L2-N BOTTOM SECTION HANGER 2 L3-N GLIDE SEAT SUPPORT 2 M1 TUBE CAP(PRE-ASSEMBLED) 2 M2 M3 SMALL NYLON BEARING (PRE-ASSEMBLED) LARGE NYLON BEARING (PRE-ASSEMBLED) 2 4 M4 GLIDE SEAT 2 M5 FOOTREST 2 Hardware used for glide ride assembly N1 BOLT 1/4”*1.5” (6.5MM*37MM) 4 N2R BOLT 1/4’’*1.7” (6.5MM*43MM) 2 N4 SCREW 0.22”*3/4” (5.5MM*19MM) 4 N5 J-BOLT 2 N6 SPRING WASHER (SMALL) 8 N8 CAP BOLT 1/4”*5/10” (6.
Part list for swing seat assembly PVC COVERED CHAIN (PRE-ASSEMBLED) J1 4 J3 EYE BOLT WITH ATTACHMENT BOLT(PRE-ASSEMBLED) 8 K1 SWING SEAT 2 Hardware used for swing seat assembly J6 NYLON NUT 5/16’’ 8 J7 5/16’’ WASHER 4 J8 PLASTIC CAP (WITH ARC WASHER) 4 J9 PLASTIC CAP (WITH FLAT WASHER) 4 Part list for trapeze assembly P1 TRAPEZE 1 T3 RUBBER CAP (PRE-ASSEMBLED) 2 S1 EYEBOLT WITH CHAIN (PRE-ASSEMBLED TO TRAPEZE) 2 Hardware used for trapeze assembly S3 PLASTIC CAP (WITH ARC WASHE
Part list for slide assembly X1-N SLIDE SUPPORT (WITH OPENING) 1 X2-N SLIDE SUPPORT 1 X3-N SLIDE LEG TUBE 2 X4-N SLIDE TOP SUPPORT BAR 1 X5-N SLIDE FRONT SUPPORT 1 X6 SLIDE LADDER STEPS 2 Y2 SLIDE 1 Hardware used for slide assembly Y1 PLASTIC CONNECTOR 2 Z1 BOLT 1/4”*1.5” (6.5MM*38MM) 6 Z2 BOLT 1/4”*4.5” (6.5MM*115MM) 2 Z3 SPRING WASHER (LARGE) 4 Z4 CAP NUT 1/4” 10 Z5 CAP BOLT 1/4”*1/2” (6.5MM*14MM) 4 Z6 SPRING WASHER (MEDIUM) 20 Z7 BOLT 1/4”*3” (6.
ASSEMBLY INSTRUCTIONS Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line, or electrical wires. Do not install the playground equipment over concrete, asphalt, packed earth, or any other hard surface; a fall onto a hard surface can result in serious injury or death to the equipment user. Adequate overhead clearance is essential.
STEP 1 – Assemble the top bar frame of the swing set Connect A1, A2 and A3 secure with B2, B3, B4 and B6 as shown below. Note: All round holes should be facing up and concave holes facing down. B3 B3 B4 B4 A3 A2 A1 B6 B6 B2 B2 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 2 – Assemble the support legs of swing set Connect A1 to A4 and secure using B1, B5, B4 and B3 as shown below. Repeat the above step for the right side of the swing set (A3 and A4, A5). A1 B4 B1 B1 B5 B3 B5 A4 A4 A5 A5 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Connect A4 to A5 and secure using B1, B5, B4 and B3 as shown below. Repeat the above step for the right side of the swing set (A3 and A4, A5). A4 A4 B5 B3 B4 B3 B1 A5 B4 B5 B1 A5 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 3 – Attach the crossbar to the support legs. Attach A6 to the outer side of A5 and secure using B2, B6, B4 and B3. A1 A4 A4 B5 B3 B4 B1 A5 A6 B3 B4 B5 A5 B1 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Attach A7 to the outer side of A5 and secure using B2, B6, B4 and B3. A3 A4 A4 B3 B5 B4 B1 B3 A7 B4 A5 B5 A5 B1 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 4 - Glide Ride assembly Attach L4 and L3 to A3 using N3R, L5 and N7 as shown. screw driver to tighten N3R and N7. Use special socket wrench and N3R L4 A3 L3 L5 L5 N7 N7 USE SPECIAL SOCKET WRENCH AND SCREW DRIVER TO TIGHTEN N7. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 5 – Glide ride assembly (continued) Insert L1-N (straight end) into L2-N and secure with N14,N6 ,N9 and N13 on both sides. Repeat the above steps on the other side N6 L1-N N9 N14 N13 N14 L2-N DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 6 – Glide ride assembly (continued) Insert L2-N (straight end) into M5 and secure with N4 and N12 on both sides. Attach M1 to the top of L1-N (curved end). Align holes and insert M2. M1 M2 L1-N L2-N N4 M5 N12 N12 N4 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 7 – Glide ride assembly (continued) Attach L1-N to L3 on both sides and secure with N2R and N10. N10 L3 N10 M1 N2R L1-N L1-N N2R L2-N L2-N DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 8 – Glide ride assembly (continued) Attach L3-N to L2-N on both sides and secure with N5, M3, N11 and N8. Concave holes face up L1-N N5 L2-N N8 M3 Round holes face down N11 N11 M3 N8 L3-N N5 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 9 – Glide ride assembly (continued) Attach M4 to L3-N and secure with N1, N6 and N9. N1 L1-N N1 L2-N M4 L3-N N6 L3-N M4 N9 M5 N6 N9 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 10 - Swing Seat assembly Connect swing set chains to the top bar by inserting J3 through A1 and securing with J8 and J6 as shown in Diagram A. Connect swing seat to the chains by inserting J3 through K1 and secure with J7, J9 and J6 as shown in Diagram B. Repeat the above steps to assemble A3 in the same manner as A1. J6 DIAGRAM A J6 J8 A1 J8 J3 J3 J1 J1 J3 J3 DIAGRAM B J1 J3 J1 J3 K1 J7 J7 J9 J9 J6 J6 DO NOT RETURN TO RETAILER YOU PURCHASED AT.
STEP 11 - Trapeze Assembly Insert S1 (which is pre-assembled with P1) through the hole on A2. Secure using S3 and P4 as shown in the diagram below. P4 S3 P4 A2 S3 S1 S1 P1 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.
Slide assembly STEP 12 - Slide assembly Insert X5-N into the base of Y2. Secure using Z8, Z6 and Z4. Attach X4-N to Y2. Note: Make sure that the bolt holes face up. Bolt hole faces up Y2 X4-N Z6 Z4 Z8 Z8 Z6 X5-N NOTE: 1.Do not over-tighten the nuts and bolts at every step. 2.Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT.
STEP 13 - Slide assembly (continued) Attach X6 to X1-N and X2-N. Secure each side using Z1, Z6 and Z4. Attach X3-N to X1-N and X2-N. Align holes and hold in position. Narrow side (Direction as shown below) X2-N Wide side faces the front direction of the slide X1-N Z4 Z6 Z1 Z6 X3-N X6 Z4 Z1 Z6 Z6 X3-N NOTE: 1.Do not over-tighten the nuts and bolts at every step. 2.
STEP 14 - Slide assembly (continued) Attach X4-N to X1-N and X2-N; Secure using Z1, Z6, Z3 and Z5 as shown in the enlarged diagram. Secure the two sides of the slide using Z2, Z6 and Z4, in the sequence shown in the diagram. X4-N Z1 X2-N Z1 Z6 X1-N Z6 Z3 Z5 Z1 Z6 Z2 Z6 Z3 Z5 Z3 Z4 Z5 Z6 Y2 X1-N Z2 Z6 X3-N NOTE: 1.Do not over-tighten the nuts and bolts at every step. 2.
STEP 15 - Slide assembly (continued) Fit Y1 in between X1-N and A6; Secure using Y1, Z7, Z6 and Z3, Z5 XN-1 Z3 Z5 Y1 Z3 Z7 Z5 Z6 A6 A5 A5 NOTE: 1.Do not over-tighten the nuts and bolts at every step. 2.Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Congratulations! You have now completed the swing set assembly. Please make sure to thoroughly check all parts and hardware to make sure all bolts and nuts are well secured before using the playground equipment. WARNING - Do not let children use the playground equipment until it is properly assembled and anchored. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Dear Customer: Thank you for your purchase of an XDP Recreation swing set. By following the instruction manual, reading all safety and assembly instructions, and properly anchoring your swing set in the ground, your kids will safely enjoy hours of fun. Detailed below is our warranty covering your purchase. Please be sure to read it and contact us in the event you need service or parts. DO NOT RETURN THE SET TO THE STORE YOU PURCHASED IT.
