Installation & Assembly

ManualsBrandsXDP Recreation ManualsBackyard PlayAll Star Playground Swing Set

“CRESTVIEW” 4 Leg Swing Set w. SeeSaw

Model # 94570

Assembled dimensions are 165" x 106" x 74". Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully

assembled.

OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S

GUIDE

WARNING!

Please read this entire instruction and assembly manual completely before proceeding. You mu st fo llo w all safet y ins truc tion s

while using this equipment. The surface area where this swing set is set up must be level and free of all debris. This set is designed

to be anchored into the ground and is not to be set up on any hard surfaces such as concrete, hardened soil, or asphalt. Proper

surfacing under and surrounding the set adds to the safety level such as sand or mulch. Read all cautionary statements on the

following pages before using this equipment and save this instruction manual. DO NOT ALLOW CHILDREN TO PLAY ON

THIS GYM SET UNSUPERVISED! CONSTANT ADULT SUPERVISION IS REQUIRED. Do not use when raining or

during any inclement weather (i.e. rain, sleet, snow, ice, high winds, thunderstorms, or lightening). DO NOT ALLOW

CHILDREN TO JUMP ON OR CLIMB UP ON THIS SET'S TOP BAR.

For warranty details and registration card see the back page of this manual.

FOLLOW ALL ASSEMBLY INSTRUCTIONS AS WRITTEN IN THIS MANUAL

Please retain sales receipt for warranty purposes. DO NOT RETURN THE SET TO

THE STORE. If replacement parts or customer service is needed please contact XDP Recreation by email at service@xdp-

recreation.com or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This gym is designed

to be used safely by up to eight (8) children, ages 3 years to 8 years, with weight capacity of 100 lbs per child or total combined weight limit

of 800 lbs for all eight (8) children. This play gym is designed for backyard use only and is NOT intended for playgrounds, schools, day

care facilities, nurseries or other public places. Follow all assembly instructions carefully and as directed in this manual. This gym

conforms to all safety requirements by ASTM for Home Playground equipment when properly assembled using the instructions enclosed.

Adult assembly is required. Contains small parts. For proper stability and safety this gym set should be installed with ground anchors.

It is highly recommended that you seek the opinion from a local licensed contractor on the best way to secure the swing set in your

location.

IF NEEDED, GROUND ANCHORS CAN BE BOUGHT FROM THE STORE YOU PURCHASED THIS SET AT OR BY

PURCHASING FROM XDP RECREATION'S WEBSITE AT www.xdp-recreation.com

Summary of content (44 pages)

PAGE 1
“CRESTVIEW” 4 Leg Swing Set w. SeeSaw Model # 94570 Assembled dimensions are 165" x 106" x 74". Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully assembled. OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE WARNING! Please read this entire instruction and assembly manual completely before proceeding. You must follow all safety instructions while using this equipment.
PAGE 2
IMPORTANT INSTRUCTIONS AND WARNINGS WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT AGE LIMIT l This product is designed to be used by up to eight (8) children between the ages of 3 to 8. Maximum user weight is 100 pounds (45 kg) each with a combined maximum weight of 800 pounds (363 kgs). l The play set is designed for children over three (3) years of age up to (8) years of age. Use by smaller children can result in entrapment or serious injury.
PAGE 3
Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall onto a hard surface can result in serious injury or death to the user.
PAGE 4
WARNING STATEMENTS – Observing the following statements and warnings reduces the likelihood of serious or fatal injury. l l DO NOT allow more than one child to play on the individual swing or slide component at any one time. DO NOT allow children to stand on the slide, swing seats, see-saw or glide ride. The glide ride is made for only two users at a time. The Stand N Swing is made for one user at a time! DO NOT allow children to walk too close to moving parts.
PAGE 5
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION l DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. l ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially hazardous to users.
PAGE 6
ANCHORING (NOTE:ANCHORS ARE NOT INCLUDED-MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping. You should consult your local contractor to decide the most appropriate way to anchor the equipment in your location.
PAGE 7
FRAME LEG 12-5/8” CONCRETE 5” 2” BRICK OR GRAVEL BED Note: The maximum fall height for this product is 4 feet. The minimum ground clearance between the bottom of the suspended plays and the playing or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground clearance. 8” WARNING Please properly anchor the swing set to minimize the risk of injury or death. If the swing set is used without proper anchoring, it may be dangerous and may tilt over.
PAGE 8
CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON: n Tighten all hardware. n Lubricate all metallic moving parts per manufacturer’s instructions. n Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. n Check all moving parts including swing seats and chains for wear, rust or other deterioration. Replace as needed. n Check metal parts for rust.
PAGE 9
TOOLS NEEDED Please prepare the following tools prior to assembling this equipment. Special Socket Wrench (Included) Hammer (If you intend to install anchor, this is needed) Wrench (Not Included) Flat Head and Philips Head Screwdriver (Not included) Tape Measure (Not included) Wrench (Included) Big Allen Wrench (Included) Medium Allen Wrench (Included) 8 Small Allen Wrench Not Included) DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.
PAGE 10
Part list for main frame assembly A1 LEFT TOP BAR 1 A2 MIDDLE TOP BAR 1 A3 RIGHT TOP BAR 1 A4 TOP SECTION LEG 4 A5 BOTTOM SECTION LEG WITH FOAM (WITH TWO HOLES) 3 A6 BOTTOM SECTION LEG WITH FOAM(WITH FOUR HOLES) 1 A7 CROSS BAR (WITH TWO HOLES) 1 A8 CROSS BAR (WITH FOUR HOLES) 1 C2 END CAP (PRE-ASSEMBLED) 2 Hardware used for main frame assembly B1 BOLT 5/16"x2-1/2" 12 B2 BOLT 5/16"x2-5/8" 4 B3 NYLON NUT 5/16’’ 16 B4 PLASTIC CAP (WITH ARC WASHER) 16 B5 ARC WASHER 5/16’’
PAGE 11
N3R BOLT 5/16”x1” 2 N7 NYLON NUT 5/16’’ 2 Part list for glide ride assembly L1-N TOP SECTION HANGER 2 L2-N BOTTOM SECTION HANGER 2 L3-N GLIDE SEAT SUPPORT 2 M1 TUBE CAP(PRE-ASSEMBLED) 2 M2 SMALL NYLON BEARING (PREASSEMBLED) 2 M3 LARGE NYLON BEARING (PREASSEMBLED) 4 M4 GLIDE SEAT 2 M5 FOOTREST 2 Hardware used for glide ride assembly N1 BOLT 1/4”x1-1/2” 4 N2R BOLT 1/4’’x1-7/10” 2 N4 SCREW 0.
PAGE 12
N13 BOLT 1/4”x1-3/8" 4 N14 ARC WASHER 5/16" 8 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 13
Part list for swing seat assembly J1 PVC COVERED CHAIN (PREASSEMBLED) 4 J3 EYE BOLT WITH ATTACHMENT BOLT(PRE-ASSEMBLED) 8 K1 SWING SEAT 2 Hardware used for swing seat assembly J6 NYLON NUT 5/16’’ 8 J7 WASHER 5/16’’ 4 J8 PLASTIC CAP (WITH ARC WASHER) 4 J9 PLASTIC CAP (WITH FLAT WASHER) 4 Part list for Standing N swing assembly G1 PVC COVERED CHAIN (PREASSEMBLED) 2 G2 PVC COVERED CHAIN (PREASSEMBLED) 4 G3 EYE BOLT WITH ATTACHMENT BOLT(PRE-ASSEMBLED) 2 G4 EYE BOLT (PRE-ASSEMBLED)
PAGE 14
Part list for slide assembly X1-N SLIDE SUPPORT (WITH OPENING) 1 X2-N SLIDE SUPPORT 1 X3-N SLIDE LEG TUBE 2 X4-N SLIDE TOP SUPPORT BAR 1 X5-N SLIDE FRONT SUPPORT 1 X6 SLIDE LADDER STEPS 2 Y2 SLIDE 1 Hardware used for slide assembly Y1 PLASTIC CONNECTOR 2 Z1 BOLT 1/4"x1-1/2" 6 Z2 BOLT 1/4"x5" 2 Z3 SPRING WASHER (LARGE) 4 Z4 CAP NUT 1/4” 10 Z5 CAP BOLT 1/4"x1/2" 4 Z6 SPRING WASHER (SMALL) 20 Z7 BOLT 1/4"x3" 2 Z8 BOLT 1/4"x2- 1/4" 4 DO NOT RETURN TO RETAILER WHER
PAGE 15
Part list for see-saw assembly U16 SEAT 2 U17 SEAT SUPPORT 1 U18 HANDLE BAR 2 U19-1 LEFT HANDLE BAR SUPPORT 2 U19-2 RIGHT HANDLE BAR SUPPORT 2 U20 L SHAPED TUBE 1 Hardware used for seesaw assembly U1 BOLT 5/16”x3-1/4” 4 U2 BOLT 5/16”x2-1/2” 1 U3 BOLT M8x2-10/16” 2 U4 ARC WASHER Φ8.
PAGE 16
U15 PLASTIC CAP (WITH ARC WASHER) 2 U21 SPRING WASHER(SMALL) 4 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 17
ASSEMBLY INSTRUCTIONS Ø Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line, or electrical wires. Ø Do not install the playground equipment over concrete, asphalt, packed earth, or any other hard surface; a fall onto a hard surface can result in serious injury or death to the equipment user. Ø Adequate overhead clearance is essential.
PAGE 18
STEP 1 – Assemble the top bar frame of the swing set Ø Connect A1 A2and A3 and secure with B3, B4, B1 and B5 as shown below. Note: All round holes should be facing up and concave holes facing down. a B3 B3 B4 B4 A3 A1 B5 A2 B5 B1 B1 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 19
STEP 2 – Assemble the support legs of swing set Ø Ø Connect A1 to A4 and secure using B1, B5, B4 and B3 as shown below. Repeat the above step for the right side of the swing set (A3 and A4). m A1 B1 B5 B5 A4 B1 A4 B3 B4 A5 A6 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 20
DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 21
g A3 B1 B5 B5 B1 A4 A4 B3 B4 A5 A5 STEP 3 – Assemble the support legs of swing set DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 22
Ø Connect A4 to A5 and A6 and secure using B1, B5, B4 and B3 as shown below. Repeat the above step for the right side of the swing set (A3 and A4, A5). rly A1 A4 B5 B1 B3 B4 B5 A5 B1 B4 B3 A6 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 23
o A3 A4 B5 B3 A4 B4 B1 B3 A5 B4 A5 B1 A5 STEP 3 – Attach the crossbar to the support legs DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 24
Ø Attach A7 to the outer side of A5, A6 and secure using B2, B6, B4 and B3. 23 A1 A4 B6 B4 B3 B2 A7 A5 B3 B6 B4 B2 A6 Attach A8 to the outer side of A5 and secure using B2, B6, B4 and B3. DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 25
a A3 A4 A4 B6 B3 B4 B3 B4 B2 A8 A5 B6 24 A5 B2 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 26
STEP 4 - Glide Ride assembly Ø Attach L4 and L3 to A3 using N3R, L5 and N7 as shown. Use special socket wrench and screw driver to tighten N3R and N7. 25 N3R L4 A3 L3 L5 L5 N7 N7 USE SPECIAL SOCKET WRENCH AND SCREW DRIVER TO TIGHTEN N7. DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 27
STEP 5 – Glide ride assembly (continued) Ø Insert L1-N (straight end) into L2-N and secure with N14,N6 ,N9 and N13 on both sides. Ø Repeat the above steps on the other side N9 N6 L1-N N14 N14 N13 L2-N DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 28
STEP 6 – Glide ride assembly (continued) Ø Insert L2-N (straight end) into M5 and secure with N4 and N12 on both sides. Ø Attach M1 to the top of L1-N (curved end). Align holes and insert M2. Ø Attach L1-N to L3 on both sides and secure with N2R and N10. 3 N10 L3 N10 M1 N2R L1-N L1-N M2 N2R L2-N L2-N L2-N N4 M5 N12 N12 N4 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 29
STEP 7– Glide ride assembly (continued) Ø Attach L3-N to L2-N on both sides and secure with N5, M3, N11 and N8. Concave holes face up L1-N N5 L2-N N8 M3 Round holes face down N11 N11 M3 N8 L3-N N5 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 30
STEP 8 – Glide ride assembly (continued) Ø Attach M4 to L3-N and secure with N1, N6 and N9. N1 L1-N N1 L2-N M4 L3-N N6 L3-N M4 N9 M5 N6 N9 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 31
STEP 9 - Swing Seat assembly Ø Connect swing set chains to the top bar by inserting J3 through A1 and securing with J8 and J6 as shown in Diagram A. Ø Connect swing seat to the chains by inserting J3 through K1 and secure with J7, J9 and J6 as shown in Diagram B. Ø Repeat the above steps to assemble A3 in the same manner as A1. – J6 DIAGRAM A J6 J8 A1 J8 J3 J3 J1 J1 J3 J3 (DIAGRAM B J1 J3 J1 J3 K1 J7 J7 J9 J9 J6 J6 DO NOT RETURN TO RETAILER WHERE PURCHASED.
PAGE 32
STEP 10 - Stand N Swing Assembly Ø Ø N Insert G3 (which is pre-assembled with G1, G2 and G4) through the hole on A2. Secure using G7 and G8 as shown in the diagram below. Insert G5 to the G6 through G7 and secure with G9 and G10 as shown in the diagram below. G7 G7 G8 G8 A2 G3 G3 G1 G4 G2 G4 G2 G10 G9 G7 G10 G6 G9 G10 G7 G9 G4 G10 G5 G7 G5 G7 G9 eNOTE: 1. Do not over-tighten the nuts and bolts at every step. 2.
PAGE 33
Slide assembly STEP 11 - Slide assembly Ø Insert X5-N into the base of Y2. Ø Secure using Z8, Z6 and Z4. Ø Attach X4-N to Y2. Ø Note: Make sure that the bolt holes face up. i Y2 X4-N Z8 Z6 Bolt hole faces up. Z4 Z6 X5-N NOTE: Z8 1.Do not over-tighten the nuts and bolts at every step. 2.Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER WHERE PURCHASED.
PAGE 34
STEP 12 - Slide assembly (continued) Ø Attach X6 to X1-N and X2-N. Ø Secure each side using Z1, Z6 and Z4. Ø Attach X3-N to X1-N and X2-N. Ø Align holes and hold in position. 1 Narrow side (Direction as shown below) X2-N Wide side faces the front direction of the slide X1-N Z6 Z1 Z4 Z6 X3-N X6 Z4 Z1 Z6 Z6 X3-N rNOTE: 1.Do not over-tighten the nuts and bolts at every step. 2.
PAGE 35
STEP 14 - Slide assembly (continued) Ø Secure the two sides of the slide using Z2, Z6 and Z4, in the sequence shown in the diagram. Ø Attach X4-N to X1-N and X2-N; Secure using Z1, Z6, Z3 and Z5 as shown in the enlarged diagram. - X4-N Z1 X2-N X1-N Z6 Z2 Z6 Z3 Z4 Z5 Z6 Y2 X1-N Z2 Z6 X3-N YNOTE: 1.Do not over-tighten the nuts and bolts at every step. 2.Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
PAGE 36
STEP 14 - Slide assembly (continued) Ø Fit Y1 in between X1-N and A6; Secure using Y1, Z7, Z6 and Z3, Z5 c Z3 Z5 X1-N Y1 Z3 Z5 Z6 Z7 A6 A5 A5 STEP 15 - See-Saw assembly DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 37
Ø Attach U20 to A5. Align the holes on U20 to the two holes on the bottom of A5 and secure using U3, U4, U15 and U5 as shown below. U15 U5 U5 U15 A6 U3 U4 U20 STEP 16 - See-Saw assembly (continued) DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 38
Ø Secure U17 to U20 by using U2, U14, U10 and U5 as shown below. f U2 U14 A6 U17 U10 U5 U20 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 39
STEP 17 - See-Saw assembly (continued) Ø Ø Attach U18 to U19-1 and U19-2 and secure using U9 and U21. Repeat for other U18, U19-1 and U19-2. e U18 U9 U21 U19-1 U21 U9 U19-2 i STEP 18 - See-Saw assembly (continued) DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 40
Ø Ø Secure U19-1 & U19-2 to U17 using U1, U4 and U5 as shown below. Repeat for the other side. m U18 U20 U19-2 U17 U5 U4 U19-1 U4 U4 U1 U4 U1 DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 41
STEP 19 - See-Saw assembly (continued) Ø Ø Secure U16 to U19-1 and U19-2 using U7, U8 and U6 as shown below. Repeat for the other side. y U7 U16 U8 U6 tNOTE: 1.Do not over-tighten the nuts and bolts at every step. 2.Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. Note: Make sure to go back to check all hardware and securely tighten all bolts and nuts before using the playground equipment.
PAGE 42
Congratulations! You have now completed the swing set assembly. Please make sure to thoroughly check all parts and hardware to make sure all bolts and nuts are well secured before using the playground equipment. UWARNING - Do not let children use the playground equipment until it is properly assembled and anchored. DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
PAGE 43
Dear Customer: Thank you for your purchase of a XDP Recreation swing set. By following the instruction manual, reading all safety and assembly instructions, and properly anchoring your swing set in the ground, your kids will safely enjoy hours of fun. Detailed below is our warranty covering your purchase. Please be sure to read it and contact us in the event you need service or parts. DO NOT RETURN THE SET TO THE STORE YOU PURCHASED IT.
PAGE 44
DO NOT RETURN TO RETAILER WHERE PURCHASED. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.