User Guide

8.9.
Introduction
Thank you for choosing a XENA disc-lock alarm: the world’s strongest, smartest,
loudest motorcycle security solution. Please read this booklet carefully.
For more information about this and other XENA locks, accessories and
product news, please visit www.xenasecurity.com
Questions or comments about your XENA product?
Email us at [e-mail]
A. XX series alarmed disc-lock parts
1. Lock barrel 2. Locking pin 3. Battery cover 4. Battery
5. Alarm module 6. Reflector 7. Spring-loaded catch 8. Module cover
9. Key tool (with key code & serial number)
Quick start guide
Your XENA XX Series disc-lock alarm comes with a CR2 long-life lithium
battery included. Please install battery before use.
Locking your motorcycle
• Insert key in lock and rotate clockwise. Lock barrel will spring open.
• Locate hole in front brake-disc sufficient to allow locking pin to pass through.
• Slide lock on to disc and depress key barrel to insert locking pin.
• Double-locking XX10 and XX14: turn key counter-clockwise to lock.
• Pushdown XX6: depress barrel until it clicks into place.
Fitting your XENA to your motorcycle’s brake disc
1. Brake disc thickness: less than 7mm (1/4”)
2. Locking pin size:
XX6 6mm (1/4”)
XX10 10mm (3/8”)
XX14 14mm (1/2”)
3. Distance from locking pin to back of disc slot*:
XX6 37-42mm (1 7/16”-1 5/8”)
XX10 46mm (1 7/8”)
XX14 44mm (1 3/4”)
Important: the locking pin can pass through ANY hole on disc
(dark areas on diagram).
Arming the alarm
• There is no on-off switch. The unit automatically senses the presence of
your brake disc.
• Important: Ensure that Reflector (A6) is covered by brake disc.
• Your XENA alarmed disc-lock is self-arming. The alarm sensors will become
active 5 seconds after being locked on your brake-disc. The alarm will beep
once to confirm that is armed.
• 10 seconds after the arming beep, shock & motion sensors work
independently to determine if your bike is being attacked.
WARNING: XENA 120dB alarms are extremely loud!
Avoid close proximity to unprotected ears.
Changing the battery (fig.B & fig.C)
• Locate spring-loaded catch inside disc slot (fig.B).
• Using end of key tool, depress catch; release and remove lid.
• Locate clear plastic tab on module and lift to remove from lock body.
• Remove battery door (marked “CR2 BATTERY”).
• Remove used battery and discard responsibly*.
• Ensure + and – contacts are properly aligned
• Insert fresh CR2 battery.
• Carefully replace module in lock body and reattach module cover.
• The key tool comes in handy to depress the spring-loaded catch.
NOTE: When module is removed from the lock body, alarm will activate.
To avoid this, insert module into lock body and replace lid immediately after
inserting battery.
B. To open lid and remove module
C. To replace the lid
Battery life
• Batteries should last 6 to 8 months with normal use. Frequent triggering or
extreme temperatures can shorten battery life.
Keys
• Each XX Series lock comes with three keys and a flat key-tool etched
with a unique code number (ie, HAB123456) and serial number
(ie, 1234567890) for ordering replacement keys. Make a note of your key
code and store safely. We encourage you to register your lock at
www.xenasecurity.com
Register your XENA lock
On the key-shaped metal tool
provided (fig.D), you'll find your
lock's two unique ID numbers:
1. Serial number, and
2. Key code.
You'll need to input both when
registering at
www.xenasecurity.com
Caring for your lock
• Use a dry cloth to keep the LED reflector plate
inside the disc-slot clean and free of dirt, dust and
grease. An obstructed reflector plate can affect
performance and may cause the lock to arm when
not on the brake disc.
• We recommend applying a lock lubricant to the lock barrel every six months.
If alarm is damaged
• The alarm module is removable. Replacement modules are available from
authorised XENA dealers or by emailing us directly at [e-mail]
NOTE: the lock remains effective with or without the alarm system.
Transporting your disc-lock
• Ideally you should carry your XENA underneath the seat of your bike.
• CAUTION: Do not carry your XENA in or attach it to your clothing, as this
may contribute to injury in the event of an accident.
Troubleshooting
• Alarm not arming: Check battery, ensure reflector (fig.E)
is obstructed by motorcycle disc. Confirm sensors are
active (see below).
• Constant clicking or low beeping sound: replace batteries.
• Alarm too sensitive: Place at 6 o’clock on disk.
• Alarm not sensitive enough: Place at 12 o’clock to
3 o’clock on disc.
• Alarm won’t disarm: Clean sensor and reflector.
Important:
How to “Wake Up” your XENA disc-lock alarm
• To avoid draining the battery when not in use, your XENA disc-lock alarm
has a dormant power mode. Usually metal-on-metal contact from locking
the lock onto your brake-disc is sufficient and the unit will arm normally.
• It may be necessary to wake up the arming sensor by firmly locking and
unlocking the key barrel once or twice.
*For more detailed troubleshooting visit www.xenasecurity.com
XX series accessories
• XXA Cable and Adaptor Set
• XENA Ground Anchor
• XBP4 Replacement Battery Pack
• XLP1 Lock Pouch
Customer care
Email us at: [e-mail]
Don’t forget to register your XENA lock at www.xenasecurity.com
Disclaimer:
Our products are sold as security enhancements, and are not a substitute for the
end-user's duties of normal care and attention. As such, XENA Security accepts no
responsibility or liability for any direct or consequential loss, damage or injury
arising or resulting from the use or misuse of our products howsoever arising,
save that we will always replace any product found to be defective within the
warranty period.
USER MANUAL for

•

•
Alarmed Disc-Locks
*Lithium batteries are best disposed of as a non-hazardous waste when fully or mostly discharged.
DO NOT INCINERATE or subject battery cells to temperatures in excess of 212°F.
!
1.
3.
4.
5.
6.
7.
2.
Reflector
E.
!
!
D.
Serial No.
0200200000

BDA
00000000
Key Code
Copyright © XENA Security. All rights reserved.こちらの製品は正規品ではありません。XENA JAPANの保証対象外となります。
062014
MGX_XX6/10/14_UM_060614 PJ1000-06062014-01G PR1000-06062014-01G** Copyright © MGX Asia Ltd
Artwork Size: 148.5mm(W) x 210mm(H) Colour: 1C (Black)