Solar Powered LED Security Camera Light & Wireless DVR MODEL: PSD3 Please do not return this item to the store. For service or questions about your solar light, call our customer service at 800.284.8828 (8:30am - 5:30pm, Monday to Friday, Pacific Time) or visit www.xepatech.com.
Introduction Thank you for purchasing the PSD3 Solar-Powered Security Light with the digital wireless DVR security system—the most cost-effective way to illuminate and protect your home, business, and recreational areas. With its easy setup and lightweight design, this light conforms to most of your lighting needs and is especially useful where an electrical outlet is not accessible.
Important Safety Information • Do not expose the light to fire or intense heat. • Do not immerse in water. • Never look directly into the light or shine it in another person’s eyes. • Dispose of the battery in accordance with local, state, and federal regulations. (Do not burn or discard the battery in a municipal water system or other body of water.) • Consult local safety guidelines for installing the light fixture on a building. • Only use batteries from XEPA TECHNOLOGIES to ensure compatibility.
What’s Inside the Package: PSD3 solar light with built-in camera and rechargeable battery Solar charging panel with 15’ cable DVR with adapter and a 2G SD card User manual, including installation template sticker Quick Start Guide Screws and anchors Audio/video connecting RCA cable Features: • Solar-powered lighting—no electricity bill • 2 x 5W super bright LEDs (equal to 60W incandescent bulb) • 2.
Product Profile: 1. 2. 3. 4. 5. 4 Lamp Head Motion Activated Indicator Motion Sensor Lens Built-in Camera Antenna 6. 7. 8. 9.
Installation Recommendations: • The PSD3 light fixture should be installed on a flat and stable surface—the higher the light is placed, the larger the area of illumination. • Avoid installing the light near an air conditioner, heater, or highvoltage system, since quick changes in temperature may activate the motion- detection system and run down the light’s power.
Installing the LED Security Light: 1. Mark holes on the wall through the Installation template. 2. Drill holes with a 3/16” drill bit. 3. Gently tap the plastic anchors into the holes until they are flush with the mounting surface. 4. Secure the screws into the plastic anchors—leave approximately 3/16” of each screw exposed for mounting the unit. 5. Place the light/camera unit over the screws—gently push down on the unit to slide the screws into locking position.
6. Rotate/tilt the motion-detection sensor/camera towards the desired coverage area. Installing the Solar Panel: 1. Find a location for the solar panel that receives direct sunlight for a minimum of 6-8 hours a day; and is within 15’ of where the Security Light will be installed. 2. Mark the holes through the mounting template. 3. Using a 3/16” drill bit, drill holes in the spots you marked.
4. Gently tap the mounting anchors into the holes until they are flush with the mounting surface. 5. Place the base of the solar panel over the drilled holes— secure the screws through the base into the plastic mounting anchors. 6. Extend the cord from the solar panel to the light box— completely insert the cable plug into the INPUT hole located on the bottom of the light unit. 7. Adjust the motion detection sensor and camera towards the desired coverage area.
Light/Camera Functions: • OFF: Neither the light nor the camera will function; the product will be completely off, but the solar panel will keep charging the battery. • AUTO: The LED light will illuminate for 1 minute when motion is detected at night. The camera will turn on when motion is detected during the day or night. Motion will be recorded for 10 seconds each time.
• Light will not work once battery is removed from the jacket. Please plug in the solar panel charger or any other approved power adaptor after put battery back to the jacket to reactivate the light. Warning: Do not mix old and new batteries and Do not mix alkaline, standard (carbonzinc) or rechargeable (ni-cad, ni-mh, etc) batteries. Only Xepa Technology rechargeable batteries should be used! It is available on www.xepatech.com or contact 800-284-8828.
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. The source of the interference can be tested by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver.
Troubleshooting Tips. Symptom Possible Solution The light will not illuminate. • Switch to TEST mode to check that the light can illuminate even during the daytime. • Make sure battery is not drained and solar panel plug is fully inserted. • Make sure the battery plug is connected inside the battery compartment. • Set switch to OFF or AUTO mode and allow the solar panel to absorb direct sunlight for two or more days to recharge the battery.
The lights on the • Check DVR menu to ensure camera is registered and auto paired. receiver do not work. There is no picture on the monitor, or the • Check that the DVR power supply is working. • Make sure the distance between the DVR and the picture is not clear. light/camera unit does not exceed 50-100 feet. • Check the connection between DVR and TV. • Adjust DVR antenna direction to capture digital signal. Motion has not been detected within the coverage area.
Product Warranty & Support Information For customer support call (800) 284-8828 between 8:30am and 5:30pm, Monday to Friday, Pacific Time or visit www.xepatech.com. This product comes with a limited warranty of 1 year from the day of purchase. (Proof of the date of purchase must be provided if the product is returned.) If the product is found to be defective in material or workmanship, APEX will replace the defective part(s).
