Phaser® 8500/8550 color printer User Guide Guide d’utilisation Guida dell'utente Benutzerhandbuch Guía del usuario Guia do Usuário Gebruikershandleiding Användarhandbok www.xerox.
Copyright © 2005 Xerox Corporation. All Rights Reserved. Unpublished rights reserved under the copyright laws of the United States. Contents of this publication may not be reproduced in any form without permission of Xerox Corporation.
Contents 1 Printer Features Parts of the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front-Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Right Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 3 Printing Basics Overview of Basic Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Supported Paper and Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper Usage Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper That Can Damage Your Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 5 Maintenance Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Cleaning the Paper Release Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 Cleaning the Maintenance Kit Wiper Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer Features This chapter includes: ■ ■ ■ ■ Parts of the Printer on page 1-2 Printer Configurations on page 1-4 Control Panel on page 1-6 More Information on page 1-10 Phaser® 8500/8550 Color Printer 1-1
Parts of the Printer Parts of the Printer This section includes: ■ ■ ■ Front-Right View on page 1-2 Right Side View on page 1-3 Rear View on page 1-3 Front-Right View 6 7 8 9 10 5 4 11 3 12 2 1 8500-044 1. Optional 525-Sheet Feeder (Tray 4) 2. Optional 525-Sheet Feeder (Tray 3) 3. Standard 525-Sheet Tray 2 4. 100-Sheet Tray 1 5. Control panel 6. Exit cover release 7. Front cover release 8. Exit cover 9. Ink loader/Top cover 10. Legal/A4 output tray extension 11. Interface cover 12.
Parts of the Printer Right Side View 1 2 3 4 5 6 7 8500-045 1. Maintenance kit 2. Waste tray 3. Power cord connection 4. Power switch 5. USB connection 6. Configuration card 7. Ethernet 10/100 Base-T connection Rear View 2 1 8500-046 1. Optional hard drive 2.
Printer Configurations Printer Configurations This section includes: ■ ■ ■ ■ Standard Features on page 1-4 Available Configurations on page 1-5 Options on page 1-5 Upgrades on page 1-5 Standard Features ■ Maximum print speed (pages per minute) based on letter-size plain paper: Phaser 8500 Color Printers Phaser 8550 Color Printers PostScript Print-Quality Modes PostScript Print-Quality Modes ■ Fast: 24 ppm ■ Fast: 30 ppm ■ Enhanced: 12 ppm ■ Standard: 24 ppm PCL Print-Quality Modes ■ Enhanc
Printer Configurations Available Configurations Printer Configurations 8500N 8500DN 8550DP 8550DT 8550DX Memory (MB) 128 128 256 256 512 Internal Hard Drive No* No* No* No* Yes Automatic 2-Sided Printing No Yes Yes Yes Yes 10/100 Ethernet Connection (networking) Yes Yes Yes Yes Yes 525-Sheet Feeder (Tray 3) No* No* No* Yes Yes 525-Sheet Feeder (Tray 4) No* No* No* No* Yes *This option can be purchased separately for this configuration.
Control Panel Control Panel This section includes: ■ ■ ■ ■ ■ Control Panel Features on page 1-6 Control Panel Layout on page 1-7 Menu Map on page 1-7 Information Pages on page 1-8 Sample Pages on page 1-8 Control Panel Features The control panel: ■ ■ ■ ■ Displays the printer’s operating status (for example, Printing, Ready to Print), printer errors, and warnings. Prompts you to load paper, order and replace supplies, and clear jams.
Control Panel Control Panel Layout 4. Back button 1. Status Indicator LED: Green: Printer is ready to print. Returns to the previous menu item. Yellow: Warning condition, printer continues to 5. Up Arrow button print. Scrolls upward through the menus. Red: Startup sequence or error condition. 6. Down Arrow button Blinking: Printer is busy or warming up. 2. Graphic display indicates status messages and menus. 3. Cancel button Cancels the current print job. Scrolls downward through the menus. 7.
Control Panel Information Pages Your printer comes with a set of information pages to help you obtain the best results from your printer. Access these pages from the control panel. Print the Menu Map to see where these information pages are located in the control panel menu structure. Note: This print icon appears before the titles of information pages that can be printed. When the information page is highlighted on the control panel, press the OK button to print that page.
Control Panel Color Sampler Pages The color sampler pages are designed to help you select colors to use in your print jobs. Each sampler page lists either the percentages of cyan, magenta, yellow, and black that are used, or the amounts (from 0 to 255) of red, green, and blue that are used. Note: Before you print the sampler pages, select the appropriate default print-quality mode and color correction on the control panel for your print job. To print the color sampler pages: 1.
More Information More Information This section includes: ■ ■ Resources on page 1-10 Xerox Support Centre on page 1-11 Obtain information regarding your printer and its capabilities from the following sources. Resources Information Source Setup Guide* Packaged with printer Quick Reference Guide* Packaged with printer User Guide (PDF) www.xerox.com/office/8500_8550support Advanced Features Guide (PDF) www.xerox.com/office/8500_8550support Video Tutorials www.xerox.
More Information Xerox Support Centre The Xerox Support Centre is a utility that is installed during printer driver installation. It appears on the desktop for Windows systems and is placed in the Utilities folder for Mac systems.
Network Basics This chapter includes: ■ ■ ■ ■ ■ Overview of Network Setup and Configuration on page 2-2 Setting Up the Network on page 2-3 Configuring the Network Address on page 2-5 Installing the Printer Drivers on page 2-9 infoSMART Knowledge Base Networking Documents (English Only) on page 2-12 This chapter provides basic information about setting up and connecting to your printer. See also: Advanced Features Guide at www.xerox.
Overview of Network Setup and Configuration Overview of Network Setup and Configuration To set up and configure the network: 1. Turn on the printer and the computer. 2. Connect the printer to the network using the recommended hardware and cables. 3. Configure the printer’s network address, which is required to identify the printer on the network.
Setting Up the Network Setting Up the Network This section includes: ■ ■ ■ Choosing a Connection Method on page 2-3 Connecting via Ethernet (Recommended) on page 2-3 Connecting via USB on page 2-4 Choosing a Connection Method Connect the printer to the network via Ethernet or USB. Hardware and cabling requirements vary for the different connection methods. Cabling and hardware are generally not included with your printer and must be purchased separately.
Setting Up the Network Standalone (Cable or DSL) Network Connection For information about setting up a cable or DSL connection for your printer, go to www.xerox.com/office/8500_8550infosmart. See also: infoSMART Knowledge Base Networking Documents (English Only) on page 2-12 Connecting via USB If you are connecting to one computer, a USB connection offers fast data speeds. However, a USB connection is not as fast as an Ethernet connection.
Configuring the Network Address Configuring the Network Address This section includes: ■ ■ ■ ■ TCP/IP and IP Addresses on page 2-5 Automatically Setting the Printer’s IP Address on page 2-5 Dynamic Methods of Setting the Printer’s IP Address on page 2-6 Manually Setting the Printer’s IP Address on page 2-8 TCP/IP and IP Addresses If your computer is on a large network, contact your network administrator for the appropriate TCP/IP addresses and additional configuration information.
Configuring the Network Address Dynamic Methods of Setting the Printer’s IP Address Set the printer’s IP address using any of the following methods. DHCP is enabled by default on all Phaser printers. ■ ■ ■ DHCP CentreWare IS AutoIP Information Required for Manual IP Addressing Information Comments Internet Protocol (IP) address of the printer Format is xxx.xxx.xxx.xxx, where xxx represents a decimal number from 0–255.
Configuring the Network Address Changing or Modifying the IP Address Using CentreWare IS CentreWare IS provides a simple interface that enables you to manage, configure, and monitor networked printers from your desktop using an embedded web server. For complete information about CentreWare IS, click the Help button in CentreWare IS to go to the CentreWare IS Online Help. After setting the printer’s IP address, you can modify TCP/IP settings using CentreWare IS. 1. 2. 3. 4. 5. 6. Launch your web browser.
Configuring the Network Address Manually Setting the Printer’s IP Address Note: Verify that your computer has a properly configured IP address for your network. Contact your network administrator for more information. If you are on a network without a DNS server, or in an environment where the network administrator assigns printer IP addresses, you can use this method to manually set the IP address. Manually setting the IP address overrides DHCP and AutoIP.
Installing the Printer Drivers Installing the Printer Drivers This section includes: ■ ■ ■ ■ Available Drivers on page 2-9 Windows 98 SE or Later and Windows 2000 or Later on page 2-10 Macintosh OS 9.x on page 2-10 Macintosh OS X Version 10.2 and Higher on page 2-11 Available Drivers To access special printing options, use a Xerox printer driver. Xerox provides drivers for a variety of page description languages and operating systems.
Installing the Printer Drivers Windows 98 SE or Later and Windows 2000 or Later To install the printer driver from the Software and Documentation CD-ROM: 1. Insert the CD-ROM into the computer’s CD-ROM drive. If the installer does not launch, do the following: a. Click Start, and then click Run. b. In the Run window, type: :\INSTALL.EXE. 2. Select your desired language from the list. 3. Select Install Printer Driver. 4.
Installing the Printer Drivers See also: Advanced Features Guide at www.xerox.com/office/8500_8550support for additional printer driver installation information Macintosh OS X Version 10.2 and Higher To install the printer driver from the Software and Documentation CD-ROM: 1. Insert the CD-ROM into the CD-ROM drive. 2. Open the Print Center utility. Note: In Macintosh OS X version 10.3 or higher, the utility is called Printer Setup Utility.
infoSMART Knowledge Base Networking Documents (English Only) infoSMART Knowledge Base Networking Documents (English Only) Go to www.xerox.com/office/8500_8550infoSMART to view these documents.
Printing Basics This chapter includes: ■ ■ ■ ■ ■ ■ Overview of Basic Steps on page 3-2 Supported Paper and Media on page 3-3 Loading Paper on page 3-8 Selecting Printing Options on page 3-20 Printing on Both Sides of the Paper on page 3-24 Printing on Specialty Media on page 3-28 See also: Using paper trays video tutorials at www.xerox.
Overview of Basic Steps Overview of Basic Steps 1. Load paper in the tray. 2. If you are prompted by the control panel, either confirm the paper type and size or change it as required. 3. From the software application, access the Print dialog box, and then select printing options in the printer driver. 4. Send the job to the printer from the software application’s Print dialog box.
Supported Paper and Media Supported Paper and Media This section includes: ■ ■ ■ ■ Paper Usage Guidelines on page 3-4 Paper That Can Damage Your Printer on page 3-4 Paper Storage Guidelines on page 3-5 Supported Paper Sizes and Weights on page 3-5 Your printer is designed to be used with a variety of paper types. Follow the guidelines in this section to ensure the best print quality and to avoid jams. For best results, use Xerox printing media specified for your Phaser 8500/8550 printer.
Supported Paper and Media Paper Usage Guidelines The printer trays accommodate most sizes and types of paper, transparencies, or other specialty media. Follow these guidelines when loading paper and media in the trays: ■ ■ ■ ■ ■ ■ ■ Use only recommended Xerox transparencies; print quality may vary with other transparencies. See the Recommended Media List at www.xerox.com/office/ 8500_8550support. Do not print on label stock once a label has been removed from a sheet. Use only paper envelopes.
Supported Paper and Media Paper Storage Guidelines Providing good storage conditions for your paper and other media contributes to optimum print quality. ■ ■ ■ ■ ■ ■ ■ Store paper in dark, cool, relatively dry locations. Most paper items are susceptible to damage from ultraviolet (UV) and visible light. UV radiation, which is emitted by the sun and fluorescent bulbs, is particularly damaging to paper items.
Supported Paper and Media Supported Paper Sizes and Weights for Tray 1 8500-008 60–220 g/m2 (16–40 lb. Bond, 50–80 lb. Cover) Index Card 3.0 x 5.0 in. Custom Sizes Statement 5.5 x 8.5 in. Executive 7.25 x 10.5 in. Margins Letter 8.5 x 11.0 in. 5 mm on all sides US Folio 8.5 x 13.0 in. Legal 8.5 x 14.0 in. A4 210 x 297 mm A5 148 x 210 mm A6 105 x 148 mm B5 JIS 182 x 257 mm ISO B5 176 x 250 mm Monarch 3.87 x 7.5 in. #10 Commercial 4.12 x 9.5 in. A7 5.25 x 7.25 in.
Supported Paper and Media Supported Paper Sizes and Weights for Trays 2, 3, or 4 8500-005 60–120 g/m2 (16–32 lb. Bond) Statement 5.5 x 8.5 in. Executive 7.25 x 10.5 in. Letter 8.5 x 11.0 in. US Folio 8.5 x 13.0 in. Legal 8.5 x 14.0 in. A4 210 x 297 mm A5 148 x 210 mm A6 105 x 148 mm B5 JIS 182 x 257 mm ISO B5 176 x 250 mm #10 Commercial 4.12 x 9.5 in.
Loading Paper Loading Paper This section includes: ■ ■ Loading Paper in Tray 1 on page 3-8 Loading Paper in Tray 2, 3, or 4 on page 3-14 Loading Paper in Tray 1 Use Tray 1 for a wide range of media types including: ■ ■ ■ ■ ■ ■ ■ ■ Plain paper, letterhead, colored paper, and pre-printed paper Card stock Labels Envelopes Transparencies Specialty media (including business cards, photo paper, postcards, pre-punched paper, weatherproof paper, and trifold brochures) Pre-printed paper (paper already printed on
Loading Paper To load paper, envelopes, or other media in Tray 1: 1. Pull down and out on the handle to open Tray 1. 8500-006 2. Open the tray extension.
Loading Paper 3. Fan the paper to release sheets that may be stuck together. 4. Insert paper, transparencies, envelopes, or specialty media into the tray. 8500-090 ■ Single-sided printing: Insert the side to be printed facedown with the top of the page entering the printer first.
Loading Paper 2-sided printing: Insert side one faceup with the bottom of the page entering the printer first. X O ER X ■ 8500-106 ■ Side-flap envelopes: Insert the envelopes with the flap side up and the flap toward the left side of the tray.
Loading Paper ■ End-flap envelopes: Fold down the flaps before placing them in the tray. Insert the envelopes with the flap side up and the flap entering the printer first. 8500-091 ■ Pre-punched paper: Insert the side to be printed facedown with the holes toward the right side of the tray. 8500-111 Note: When using pre-punched paper, adjust the print margins to accommodate the holes. Printing over the holes may cause ink to transfer onto subsequent pages. A minimum margin of 19 mm (0.75 in.
Loading Paper 5. Adjust the paper guides to fit the paper loaded in the tray. 8500-126 6. On the control panel, press the OK button to use the paper size and type displayed as the current setup, or change the paper size and type: a. Select Change setup, and then press the OK button. b. Select the paper size, and then press the OK button. c. Select the paper type, and then press the OK button.
Loading Paper Loading Paper in Tray 2, 3, or 4 Use Tray 2, 3, or 4 for a wide range of media including: ■ ■ ■ ■ ■ ■ ■ Plain paper, letterhead, and pre-printed paper Card stock Labels Envelopes: #10 Commercial, C5 (side-flap only), and DL Transparencies Specialty media (including photo paper, postcards, pre-punched paper, weatherproof paper, and trifold brochures) Pre-printed paper (paper already printed on one side) See also: Supported Paper Sizes and Weights for Trays 2, 3, or 4 on page 3-7 Printing on
Loading Paper To load paper, envelopes, or other media in Tray 2, 3, or 4: 1. Remove the tray from the printer. 8500-002 2. Fan the paper to release sheets that may be stuck together.
Loading Paper P S A H E R 3. Insert paper, transparencies, envelopes, or specialty media into the tray. ■ Single-sided printing: Insert the side to be printed faceup with the top of the page toward the front of the tray. 8500-092 ■ 2-sided printing: Insert side one facedown with the top of the page toward the back of the tray.
Loading Paper ■ Side-flap envelopes: Insert the envelopes with the flap side down and the flap toward the left side of the tray. Caution: There are separate fill lines inside the tray for envelopes and for other media. Do not load the tray above the appropriate fill line. Overloading the tray can cause jams. ■ Pre-punched paper: Insert the side to be printed faceup with the holes toward the right side of the tray. Note: When using pre-punched paper, adjust the print margins to accommodate the holes.
Loading Paper 4. Adjust the paper guides to fit the paper loaded in the tray (if necessary). ■ Length guide: Press the sides, then slide the guide until the arrow on the guide points to the appropriate paper size imprinted on the bottom of the tray. When properly positioned, the guide clicks into place. 8500-107 ■ Width guides: Slide the width guides until the arrows on the guides point to the appropriate paper size labeled on the bottom of the tray. When properly positioned, the guides click into place.
Loading Paper 5. Insert the tray into the tray slot and push it completely into the printer. 6. On the control panel: a. Select Paper Tray Setup, and then press the OK button. b. Select either Tray 2 Paper Type, Tray 3 Paper Type, or Tray 4 Paper Type, and then press the OK button. c. Select the appropriate paper type, and then press the OK button.
Selecting Printing Options Selecting Printing Options This section includes: ■ ■ ■ Selecting Printing Preferences (Windows) on page 3-20 Selecting Options for an Individual Job (Windows) on page 3-20 Selecting Options for an Individual Job (Macintosh) on page 3-22 See also: Advanced Features Guide at www.xerox.com/office/8500_8550support Selecting Printing Preferences (Windows) Printer preferences control all of your print jobs, unless you override them specifically for a job.
Selecting Printing Options See the following table for specific printing options: Printing Options for Windows Operating Systems Operating System Windows 2000, Windows XP, or Windows Server 2003 Driver Tab Printing Options Layout tab ■ Orientation ■ Print on Both Sides ■ Pages per sheet ■ Paper type, size, and tray selection ■ Cover pages ■ Print quality ■ Separation pages ■ Secure prints, personal prints, proof prints, and saved prints ■ End of job notification ■ Color corrections
Selecting Printing Options Selecting Options for an Individual Job (Macintosh) To select print settings for a particular job, change the driver settings before sending the job to the printer. 1. With the document open in your application, click File, and then click Print. 2. Select the desired printing options from the menus and drop-down lists that are displayed. Note: In Macintosh OS X, click Save Preset on the Print menu screen to save the current printer settings.
Selecting Printing Options Macintosh PostScript Driver Settings (Continued) Operating System Driver Drop-Down Title Printing Options Mac OS 9.
Printing on Both Sides of the Paper Printing on Both Sides of the Paper This section includes: ■ ■ Automatic 2-Sided Printing on page 3-24 Manual 2-Sided Printing on page 3-26 Automatic 2-Sided Printing Automatic 2-sided printing is available from all trays. Before printing a 2-sided document, verify the following requirements: ■ The printer is a Phaser 8500DN, Phaser 8550DP, Phaser 8550DT, or Phaser 8550DX configuration.
Printing on Both Sides of the Paper Selecting 2-Sided Printing To select automatic 2-sided printing: 1. Insert paper in the tray. ■ Tray 1: Insert side one faceup with the bottom of the page entering the printer first. ■ Tray 2, 3, or 4: Insert side one facedown with the top of the page toward the back of the tray. 2. Select 2-sided printing in the printer driver. To select automatic 2-sided printing: Operating System Steps Windows 98 SE or Windows Me 1. Select the Setup tab. 2. Select Print on 2 Sides.
Printing on Both Sides of the Paper Manual 2-Sided Printing You can manually print on both sides of the paper when you are using paper types that are either too small or too heavy for automatic 2-sided printing. The Phaser 8500N printer does not have automatic 2-sided printing. Manual 2-sided printing is available with this printer. You can also manually print on the second side of paper that is pre-printed on side one.
Printing on Both Sides of the Paper Printing Side Two 1. Remove the paper from the output tray and reload it in the paper tray: ■ Tray 1: Insert side two facedown with the top of the page entering the printer first. ■ Tray 2, 3, or 4: Insert side two faceup with the top of the page toward the front of the tray. 2. Select 2nd Side on the control panel: Tray 1 Tray 2, 3, or 4 a. Select Change setup, and then press the OK button. a. Select Paper Tray Setup, and then press the OK button. b.
Printing on Specialty Media Printing on Specialty Media This section includes: ■ ■ ■ ■ ■ Printing Transparencies on page 3-28 Printing Envelopes on page 3-34 Printing Labels on page 3-40 Printing Glossy Paper on page 3-46 Printing Custom Size Paper on page 3-52 Printing Transparencies Transparencies can be printed from any tray. They should be printed on one side only. Use only recommended Xerox transparency film. See the Recommended Media List at www.xerox.com/office/8500_8550support.
Printing on Specialty Media Printing Transparencies from Tray 1 To print transparencies: 1. Pull down and out on the handle to open Tray 1. 8500-006 2. Open the tray extension.
Printing on Specialty Media 3. Insert transparencies into the tray and adjust the paper guides to fit the transparencies. 8500-101 4. On the control panel, press the OK button if the correct paper size and Transparency are displayed as the current setup, or select the transparency size and type: a. Select Change setup, and then press the OK button. b. Select the appropriate size, and then press the OK button. c. Select Transparency, and then press the OK button. 5.
Printing on Specialty Media 2. Insert transparencies into the tray. 8500-102 Note: Do not load transparencies above the paper fill line inside the tray.
Printing on Specialty Media 3. Adjust the paper guides to fit the transparencies (if necessary). ■ Length guide: Press the sides, then slide the guide until the arrow on the guide points to the appropriate paper size imprinted on the bottom of the tray. When properly positioned, the guide clicks into place. 8500-114 ■ Width guides: Slide the width guides until the arrows on the guides point to the appropriate paper size labeled on the bottom of the tray.
Printing on Specialty Media 4. Insert the tray into the tray slot, and then push it completely into the printer. 8500-104 5. On the control panel: a. Select Paper Tray Setup, and then press the OK button. b. Select either Tray 2 Paper Type, Tray 3 Paper Type, or Tray 4 Paper Type, and then press the OK button. c. Select Transparency, and then press the OK button. 6. In the printer driver, select either Transparency as the paper type or the appropriate tray as the paper source.
Printing on Specialty Media Printing Envelopes Envelopes can be printed from Tray 1 and Tray 2, 3, or 4 depending on the type of envelope you are using. See also: Supported Paper Sizes and Weights for Tray 1 on page 3-6 Supported Paper Sizes and Weights for Trays 2, 3, or 4 on page 3-7 Guidelines ■ ■ ■ ■ ■ ■ Use only paper envelopes specified in the Supported Papers table. Successful envelope printing is highly dependent on the quality and construction of the envelopes.
Printing on Specialty Media Printing Envelopes from Tray 1 To print envelopes: 1. Pull down and out on the handle to open Tray 1. 8500-006 2. Open the tray extension.
Printing on Specialty Media 3. Insert a maximum of 10 envelopes into the tray and adjust the paper guides to fit the envelopes: ■ Side-flap envelopes: Insert the envelopes with the flap side up and the flap of the envelopes toward the left side of the tray. 8500-010 ■ End-flap envelopes: Fold down the flaps before placing them in the tray. Insert the envelopes with the flap side up and the flap entering the printer first. 8500-091 4.
Printing on Specialty Media Printing Envelopes from Tray 2, 3, or 4 To print envelopes: 1. Remove the tray from the printer. 8500-102 2. Insert a maximum of 40 envelopes into the tray, flap side down with the flap toward the left side of the tray.
Printing on Specialty Media 3. Adjust the paper guides to fit the envelopes. ■ Length guide: Press the sides, then slide the guide until the arrow on the guide points to the appropriate paper size imprinted on the bottom of the tray. When properly positioned, the guide clicks into place. 8500-116 ■ Width guides: Slide the width guides until the arrows on the guides point to the appropriate paper size labeled on the bottom of the tray. When properly positioned, the guides click into place.
Printing on Specialty Media 4. Insert the tray into the tray slot, and then push it completely into the printer. 8500-127 5. On the control panel: a. Select Paper Tray Setup, and then press the OK button. b. Select either Tray 2 Paper Type, Tray 3 Paper Type, or Tray 4 Paper Type, and then press the OK button. c. Select Envelope and then press the OK button. 6. In the printer driver, select either Envelope as the paper type or the appropriate tray as the paper source.
Printing on Specialty Media Printing Labels Labels can be printed from any tray. To order paper, transparencies, or other specialty media, contact your local reseller or go to www.xerox.com/office/supplies. See also: Supported Paper Sizes and Weights for Tray 1 on page 3-6 Supported Paper Sizes and Weights for Trays 2, 3, or 4 on page 3-7 Guidelines ■ ■ ■ ■ ■ ■ Do not use vinyl labels. Print only on one side of the sheet of labels.
Printing on Specialty Media Printing Labels from Tray 1 To print labels: 1. Pull down and out on the handle to open Tray 1. 2. Open the tray extension.
Printing on Specialty Media 3. Insert a maximum of 50 sheets of labels into the tray with the side to be printed facedown and the top of the page entering the printer first. 4. Adjust the paper guides to fit the labels loaded in the tray. 5. On the control panel, press the OK button if the correct paper size and Labels are displayed as the current setup, or select the label size and type: a. Select Change setup, and then press the OK button. b.
Printing on Specialty Media 3. Adjust the paper guides to fit the labels (if necessary). ■ Length guide: Press the sides, then slide the guide until the arrow on the guide points to the appropriate paper size imprinted on the bottom of the tray. When properly positioned, the guide clicks into place. 8500-119 ■ Width guides: Slide the width guides until the arrows on the guides point to the appropriate paper size labeled on the bottom of the tray. When properly positioned, the guides click into place.
Printing on Specialty Media 4. Insert the tray into the tray slot, and then push it completely into the printer. 8500-120 5. On the control panel: a. Select Paper Tray Setup, and then press the OK button. b. Select either Tray 2 Paper Type, Tray 3 Paper Type, or Tray 4 Paper Type, and then press the OK button. c. Select Labels, and then press the OK button. 6. In the printer driver, select either Labels as the paper type or the appropriate tray as the paper source.
Printing on Specialty Media Printing Glossy Paper Glossy paper can be printed, one- or 2-sided, from any tray. To order paper, transparencies, or other specialty media, contact your local reseller or go to www.xerox.com/office/supplies. Guidelines ■ ■ ■ ■ ■ Do not open sealed packages of glossy paper until you are ready to load them into the printer. Leave glossy paper in the original wrapper, and leave the packages in the shipping carton until ready to use.
Printing on Specialty Media Printing Glossy Paper from Tray 1 To print glossy paper: 1. Pull down and out on the handle to open Tray 1. 8500-006 2. Open the tray extension.
Printing on Specialty Media 3. Insert a maximum of 50 sheets of glossy paper in the tray. Adjust the paper guides to fit the paper. 8500-075 4. On the control panel, press the OK button if the correct paper size and Special are displayed as the current setup, or select the glossy paper size and type: a. Select Change setup, and then press the OK button. b. Select the appropriate paper size, and then press the OK button. c. Select Special, and then press the OK button. 5.
Printing on Specialty Media Printing Glossy Paper from Tray 2, 3, or 4 To print glossy paper: 1. Remove the tray from the printer. 2. Insert a maximum of 400 sheets of glossy paper into the tray.
Printing on Specialty Media 3. Adjust the paper guides to fit the glossy paper (if necessary). ■ Length guide: Press the sides, then slide the guide until the arrow on the guide points to the appropriate paper size imprinted on the bottom of the tray. When properly positioned, the guide clicks into place. 8500-107 ■ Width guides: Slide the width guides until the arrows on the guides point to the appropriate paper size labeled on the bottom of the tray.
Printing on Specialty Media 4. Insert the tray into the tray slot, and then push it completely into the printer. 5. On the control panel: a. Select Paper Tray Setup, and then press the OK button. b. Select either Tray 2 Paper Type, Tray 3 Paper Type, or Tray 4 Paper Type, and then press the OK button. c. Select Special, and then press the OK button. 6. In the printer driver, select either Special as the paper type or the appropriate tray as the paper source.
Printing on Specialty Media Printing Custom Size Paper In addition to the wide variety of standard paper sizes that you can use for printing, you can also print on custom size paper within the following dimensions. Note: Print custom size paper from Tray 1 only. Size Range Single-Sided Printing 2-Sided Printing Width 76–216 mm (3.0–8.5 in.) 140–216 mm (5.5–8.5 in.) Height 127–356 mm (5.0–14.0 in.) 210–356 mm (8.3–14.0 in.) Weight 60–220 g/m2 60–120 g/m2 (16–40 lb. Bond) (22–80 lb.
Printing on Specialty Media Printing Custom Size Paper from Tray 1 To print custom size paper: 1. Pull down and out on the handle to open Tray 1. 8500-006 2. Open the tray extension.
Printing on Specialty Media 3. Insert custom size paper into the tray: ■ Single-sided printing: Insert the side to be printed facedown with the top of the page entering the printer first. 8500-009 O X 2-sided printing: Insert side one faceup with the bottom of the page entering the printer first.
Printing on Specialty Media 4. Adjust the paper guides to fit the paper loaded in the tray. 5. On the control panel, press the OK button if the correct paper size and paper type are displayed as the current setup, or select the appropriate paper size and type: a. Select Change setup, and then press the OK button. b. Select New Custom Size, and then press the OK button. c. Select the appropriate paper type, and then press the OK button. 6. In the printer driver, select Tray 1 as the paper source.
Print Quality This chapter includes: ■ ■ Controlling the Quality of Your Prints on page 4-2 Solving Print-Quality Problems on page 4-5 Phaser® 8500/8550 Color Printer 4-1
Controlling the Quality of Your Prints Controlling the Quality of Your Prints This section includes: ■ ■ Selecting a Print-Quality Mode on page 4-2 Adjusting Color on page 4-3 The print-quality mode and TekColor correction directly control the quality of your prints. The print-quality mode and paper type directly control the print speed. You can change these settings in the printer driver or on the control panel. Note: Driver settings override the control panel settings.
Controlling the Quality of Your Prints To select the print-quality mode in a supported driver: Operating System Steps Windows 98 SE or Windows Me 1. Select the Setup tab. Windows 2000, Windows XP, Windows Server 2003, or Windows NT 4.x 1. Select the Paper/Quality tab. Mac OS 9.x 1. In the Print dialog box, select General. 2. Select a print-quality mode. 2. Select a print-quality mode. 2. Select Print Quality from the drop-down list. 3. Select the desired mode for Quality. Mac OS X, version 10.
Controlling the Quality of Your Prints See also: www.xerox.com/office/8500_8550infoSMART for information about color matching and ICC profiles To select the color correction in a supported driver: Operating System Steps Windows 98 SE, Windows Me, Windows 2000, Windows XP, Windows Server 2003, or Windows NT 4.x 1. Select the TekColor tab. Mac OS 9.x 1. In the Print dialog box, select General. 2. Select the desired color correction.
Solving Print-Quality Problems Solving Print-Quality Problems This section includes: ■ ■ ■ ■ ■ Smudges or Smears on page 4-5 Random Light Stripes on page 4-6 Predominate Light Stripes on page 4-7 Transparency Images Are Too Light or Too Dark on page 4-8 Colors Are Wrong on page 4-8 Smudges or Smears Problem Smudges or smears appear on the page. Solution To prevent smudges or smears from appearing on the page: 1.
Solving Print-Quality Problems 3. If the problem continues: a. Open the door on the right side of the printer and remove the maintenance kit. b. Wipe the plastic wiper blade with a lint-free cloth. c. Replace the maintenance kit and close the door. Note: Smudges or smears may appear if you print on side two of pre-printed paper, but do not select 2nd Side as the paper type. Select the 2nd Side option on the control panel and in the printer driver.
Solving Print-Quality Problems 5. If the problem continues, select Jet Substitution Mode to substitute a jet for the malfunctioning jet causing the light stripe. The printer has been designed to compensate for a malfunctioning jet. See Print Quality Problems on the control panel for more information. To select Jet Substitution Mode: a. b. c. d. e. On the control panel, select Troubleshooting, and then press the OK button. Select Print Quality Problems, and then press the OK button.
Solving Print-Quality Problems Transparency Images Are Too Light or Too Dark Problem Text or graphics printed on transparencies are either too light or too dark. Solution 1. Verify that Transparency is selected in the software application or in the printer driver. 2. On the control panel, verify that the tray containing the transparencies is set to print transparencies: a. Select Paper Tray Setup, and then press the OK button. b.
Maintenance This chapter includes: ■ ■ ■ Maintenance and Cleaning on page 5-2 Ordering Supplies on page 5-14 Moving and Repacking the Printer on page 5-16 See also: Maintenance video tutorials at www.xerox.com/office/8500_8550support Replacing supplies video tutorials at www.xerox.
Maintenance and Cleaning Maintenance and Cleaning This section includes: ■ ■ ■ ■ Routine Maintenance on page 5-2 Cleaning the Paper Release Blade on page 5-9 Cleaning the Maintenance Kit Wiper Blade on page 5-11 Cleaning the Outside of the Printer on page 5-13 See also: User Safety on page A-1 Routine Maintenance Your system needs little maintenance to keep it producing quality prints. Add ink, empty the waste tray, and replace the maintenance kit when needed to keep your printer functioning properly.
Maintenance and Cleaning 2. Open the top cover. 8500-019 3. Locate the ink-loading bin that is low. A label above each bin indicates the color and color number for that bin. Note: Each ink stick has a number that corresponds to the number on the ink-loading bin. 4. Remove the ink stick from its packaging. Place the ink stick into the opening of the appropriate ink-loading bin. Do not force the ink stick into the ink-loading bin. Each ink stick is uniquely shaped to fit into the correct ink-loading bin.
Maintenance and Cleaning 5. Close the top cover. Warming Up is displayed on the control panel until the printer is ready for printing. Note: To minimize ink waste and optimize performance, leave the printer on all the time. ■ ■ ■ Keep ink in its packaging until you are ready to use it. Identify ink by number and shape, not color. To avoid ink jams, never insert broken ink sticks into the ink-loading bins. To order ink, contact your local reseller or go to www.xerox.com/office/8500_8550supplies.
Maintenance and Cleaning 2. Pull the waste tray (labeled B) completely out of the printer. Warning: The waste tray may be hot; handle it carefully. 8500-035 Note: The waste tray may be locked if the printer is in a warm-up cycle or if the ink is cooling following the Eliminate Light Stripes troubleshooting routine. If the tray is locked, close the door and wait 15 minutes before repeating Steps 1 and 2. 3. Empty the waste tray in a waste container.
Maintenance and Cleaning 4. Insert the waste tray into the printer and push it completely into the waste tray slot. 8500-068 5. Close the side door. 8500-038 Caution: Do not attempt to reuse the waste ink in the printer; it can damage the printer. This damage is not covered under the printer warranty.
Maintenance and Cleaning Replacing the Maintenance Kit The maintenance kit contains a maintenance roller that keeps the surface of the imaging drum clean and oiled. Note: Order a new maintenance kit when the control panel displays a message that the maintenance kit is low. Replace it when the control panel prompts you to replace the maintenance kit. To order a replacement maintenance kit, contact your local reseller or go to www.xerox.com/office/8500_8550supplies. To replace the maintenance kit: 1.
Maintenance and Cleaning 3. Insert the replacement maintenance kit and push it completely into the maintenance kit slot. Follow the illustrated instructions included with the maintenance kit for full installation and disposal information. 4. Close the door.
Maintenance and Cleaning 3. Wipe the plastic paper release blade on the lower paper guide with a pre-soaked alcohol cloth (using 90 percent isopropyl alcohol). 8500-084 4. Lower the paper guide to its original position. 8500-080 5. Close the exit cover.
Maintenance and Cleaning Cleaning the Maintenance Kit Wiper Blade To clean the maintenance kit wiper blade: 1. Open the door on the right side of the printer. 8500-034 2. Remove the maintenance kit (labeled A) from the maintenance kit slot. 8500-032 3. Use a lint-free cloth to clean the top and upper edges of the flexible plastic wiper blade located next to the roller.
Maintenance and Cleaning 4. Insert the maintenance kit and push it completely into the maintenance kit slot. 8500-033 5. Close the door.
Maintenance and Cleaning Cleaning the Outside of the Printer To remove stains, clean the outside of the printer using a soft, damp, cloth moistened with a mild neutral detergent. Do not spray detergent directly onto the printer. Warning: To prevent electric shock, turn the printer off and unplug the power cord from the electrical outlet before cleaning the printer.
Ordering Supplies Ordering Supplies This section includes: ■ ■ ■ ■ Consumables on page 5-14 Routine Maintenance Items on page 5-14 When to Order Supplies on page 5-15 Recycling Supplies on page 5-15 Certain consumables and routine maintenance items need to be ordered occasionally. Each item includes installation instructions in the package. Consumables The only consumable for the Phaser 8500/8550 printer is Genuine Xerox Solid Ink 8500/8550 (Cyan, Magenta, Yellow, and Black).
Ordering Supplies When to Order Supplies The control panel displays a warning when the supply nears its replacement time. Verify that you have replacements on hand. It is important to order these supplies when the messages first appear to avoid interruptions to your printing. The control panel displays an error message when the supply must be replaced. To order supplies, contact your local reseller or go to the Xerox Supplies website at www.xerox.com/office/8500_8550supplies.
Moving and Repacking the Printer Moving and Repacking the Printer This section includes: ■ ■ ■ Precautions for Moving the Printer on page 5-16 Moving the Printer Within the Office on page 5-16 Preparing the Printer for Shipment on page 5-18 Caution: Parts of the printer are hot. To avoid personal injury or damage to the printer, allow the ink to solidify. Run the Shut Down for Moving Printer procedure on the control panel to cool the printer quickly.
Moving and Repacking the Printer 3. Within 10 seconds after turning off the printer, select Shut Down for Moving Printer on the control panel. Note: If you receive a Power Down Error-Head not Parked message at the control panel, the printer is not ready to be moved. If the printhead is not locked, the printer can be damaged during shipment. 4. Verify that the flag in the exit tray is in the raised position. When the flag is raised, the printhead is locked. 8500-099 5.
Moving and Repacking the Printer Removing the Maintenance Kit and Waste Tray Before turning off the printer, remove the maintenance kit and waste tray: 1. Open the door on the right side of the printer. 8500-034 2. Remove the maintenance kit (labeled A) and place it in a plastic bag for storage.
Moving and Repacking the Printer 3. Remove the waste tray (labeled B) from the waste tray slot. Warning: The waste tray may be hot; handle it carefully. 4. Empty the waste, and then place the tray in a plastic bag for storage. Caution: Shipping the printer with the maintenance kit and waste tray installed can damage the printer. 5. Close the printer’s door and covers.
Moving and Repacking the Printer Turning Off the Printer To turn off the printer: 1. Press the power switch located under the interface cover on the right side of the printer to turn it off. 8500-030 2. Within 10 seconds after turning off the printer, select Shut Down for Moving Printer on the control panel. Caution: If you receive a Power Down Error-Head not Parked message at the control panel, the printer is not ready to be moved.
Moving and Repacking the Printer Packing the Printer To pack the printer: 1. Use the hand holds on each side of the printer to lift it. Move the printer separately from the 525-Sheet Feeder. 28 kg 60 lb. 2. Use the original packing material and box, or a Xerox repackaging kit, to repack the printer. Do not ship the maintenance kit or waste tray with the printer.
Troubleshooting This chapter includes: ■ ■ Clearing Paper Jams on page 6-2 Getting Help on page 6-18 See also: Troubleshooting video tutorials at www.xerox.
Clearing Paper Jams Clearing Paper Jams This section includes: ■ ■ ■ Jam at the Exit on page 6-2 Jam at the Front Cover on page 6-8 Jam at the Trays on page 6-13 See also: User Safety on page A-1 Jam at the Exit To clear a jam at the exit: 1. Open the exit cover. 8500-016 2. Pull the jammed paper slowly out of the printer. Confirm that any torn pieces of paper are removed.
Clearing Paper Jams 3. If you did not find paper in Step 2, lift the paper guides. 2 1 8500-042 4. Remove any jammed paper. 8500-065 5. Close the exit cover.
Clearing Paper Jams 6. If you did not find paper in the previous steps, follow these steps: a. Pull up the latch on the front of the printer to open the front cover. 8500-012 b. Pull the jammed paper slowly out of the printer. Confirm that any torn pieces of paper are removed.
Clearing Paper Jams c. Close the front cover.
Clearing Paper Jams 7. If you did not find jammed paper in the previous steps, follow these steps: a. Pull all the trays completely out of the printer. 8500-028 b. Remove any jammed paper from inside the tray slot. Confirm that any torn pieces of paper are removed.
Clearing Paper Jams Jam at the Front Cover To clear a jam at the front cover: 1. Pull up the latch on the front of the printer to open the front cover. 8500-012 2. Pull the jammed paper slowly out of the printer. Confirm that any torn pieces of paper are removed.
Clearing Paper Jams 3. Close the front cover. 8500-014 4. If you did not find paper in the previous steps, follow these steps: a. Open the exit cover.
Clearing Paper Jams b. Pull the jammed paper slowly out of the printer. Confirm that any torn pieces of paper are removed. 8500-017 c. Lift the paper guides. d. Remove jammed paper.
Clearing Paper Jams e. Close the exit cover. 8500-018 5. If you did not find jammed paper in the previous steps, follow these steps: a. Pull all the trays completely out of the printer.
Clearing Paper Jams b. Remove any jammed paper from inside the tray slot. Confirm that any torn pieces of paper are removed. 8500-024 c. Replace all trays and push each one completely into the printer. Note: Use only the approved paper type, weight, and size for this tray. Print custom size paper from Tray 1 only.
Clearing Paper Jams Jam at the Trays To clear a jam from the tray specified on the control panel: 1. Pull the tray specified on the control panel completely out of the printer. 8500-002 2. Remove the top sheet from the tray.
Clearing Paper Jams 3. Verify that the paper is loaded correctly in the tray. Adjust the length and width tray guides: a. Length guide: Press the sides, then slide the guide until the arrow on the guide points to the appropriate paper size imprinted on the bottom of the tray. When properly positioned, the guide clicks into place. 8500-107 b. Width guides: Slide the width guides until the arrows on the guides point to the appropriate paper size labeled on the bottom of the tray.
Clearing Paper Jams 4. Remove jammed paper inside the tray slot. Confirm that any torn pieces of paper are removed. 8500-024 5. Insert the tray into the tray slot and push it completely into the printer.
Clearing Paper Jams 6. If you did not find jammed paper in the previous steps, follow these steps: a. Pull up the latch on the front of the printer to open the front cover. 8500-012 b. Pull the jammed paper slowly out of the printer. Confirm that any torn pieces of paper are removed.
Clearing Paper Jams c. Close the front cover. 8500-014 Note: Use only the approved paper type, weight, and size for this tray. Print custom size paper from Tray 1 only.
Getting Help Getting Help This section includes: ■ ■ ■ ■ Control Panel Messages on page 6-18 PrintingScout Alerts on page 6-19 PhaserSMART Technical Support on page 6-19 Web Links on page 6-20 Xerox provides several automatic diagnostic tools to help you produce and maintain print quality. See also: Xerox Support Centre on page 1-11 Control Panel Messages The control panel provides you with information and troubleshooting help.
Getting Help PrintingScout Alerts PrintingScout is a tool that is installed with your Xerox printer driver. It automatically checks the printer status when you send a print job. If the printer is unable to print your job, PrintingScout automatically displays an alert on your computer screen to let you know that the printer needs attention. Click the alert to view instructions explaining how to fix the problem.
Getting Help Web Links Xerox provides several websites that offer additional help on your Phaser 8500/8550 printer. A set of Xerox links is installed in your web browser’s Favorites folder when you install the Xerox printer drivers on your computer. The Troubleshooting tab in your Windows printer driver also includes useful links. Use the following websites to obtain more information.
User Safety Your printer and the recommended supplies have been designed and tested to meet strict safety requirements. Attention to the following information ensures the continued safe operation of your printer. Electrical Safety ■ ■ ■ ■ ■ Use the power cord supplied with your printer. Plug the power cord directly into a properly grounded electrical outlet. Make sure each end of the cord is securely connected. If you do not know if an outlet is grounded, ask an electrician to check the outlet.
The power cord is attached to the printer as a plug-in device at the back of the printer. If it is necessary to disconnect all electrical power from the printer, disconnect the power cord from the electrical outlet. Warning: Do not remove the covers or guards that are fastened with screws unless you are installing optional equipment and are specifically instructed to do so. Power should be OFF when performing these installations.
Printer Location ■ ■ ■ ■ ■ ■ Place the printer in a dust-free area within a temperature range of 50° F to 90° F (10° C to 32° C) and a relative humidity range of 10 percent to 80 percent. Place the printer in an area where there is adequate space for ventilation, operation, and servicing. Do not place the printer on a carpeted floor. Airborne carpet fibers can be pulled into the printer and cause print-quality problems. Do not place the printer near a heat source.
Moving the Printer Follow these guidelines to avoid injuring yourself or damaging the printer: ■ ■ ■ Keep the printer level. Tilting the printer can cause the ink to spill inside. Use the Shut Down for Moving Printer mode on the control panel for best results. Always allow the printer to cool before it is moved to avoid ink spills that can damage the printer. Warning: Parts of the printer may be hot.
■ ■ Never move the printer if you receive a Power Down Error-Head not Parked message on the control panel. The printer is not ready to be moved. If the printhead is not locked, the printer can be damaged during shipment. Verify that the printhead is locked. When the green flag in the exit tray is in the raised position, the printhead is locked. 8500-099 ■ ■ Always move the printer separately from the lower tray assembly. Always use two people to lift the printer. 28 kg 60 lb.
Symbols Marked on Product Use caution (or draws attention to a particular component). See the manual(s) for information. Avoid pinching fingers in the printer. Use caution to avoid personal injury. Hot surface on or in the printer. Use caution to avoid personal injury. Do not touch.
Index Numerics adding ink, 5-2 adjusting color, 4-3 AutoIP manually setting the printer’s IP address, 2-8 setting the printer’s IP address dynamically, 2-6 automatic TekColor correction, 4-3 automatically setting the printer’s IP address, 2-5 available printer drivers, 2-9 colors adjusting, 4-3 description, 4-3 configuring the network address, 2-5 connection cable or DSL, 2-4 Ethernet, 2-3 standalone network, 2-4 USB, 2-4 consumables, 5-14 control panel, 1-6 controlling print-quality, 4-2 features and lay
Index drivers available, 2-9 installing, 2-9 Macintosh, 2-9 Macintosh OS 9.x, 2-10 Macintosh OS X, version 10.
Index J jams at the exit, 6-2 at the front cover, 6-8 at the trays, 6-13 clearing, 6-2 preventing, 6-2 jet substitution, 4-6 job individual printing options Macintosh, 3-22 Windows, 3-20 selecting a print-quality mode, 4-2 selecting printing options Windows, 3-20 media supported, 3-3 memory, 1-5 Menu Map, 1-7 messages control panel, 6-18 PrintingScout, 6-19 modifying the IP address using CentreWare IS, 2-7 moving the printer, A-4 precautions, 5-16 preparing for shipment, 5-18 repacking, 5-16 within the of
Index P paper 2nd side, 3-26 custom sizes, 3-52 damaging to the printer, 3-4 envelopes, 3-34 glossy, 3-46 guidelines for printing glossy paper, 3-46 jams, 6-2 labels, 3-40 loading in the paper trays, 3-8 margins, 3-6, 3-7, 3-52 Paper Tips page, 3-5, 4-5, 4-8 pre-printed, 3-26 printing on specialty media, 3-28 storage guidelines, 3-5 supported, 3-3, 3-5 supported for Tray 1, 3-6 supported sizes and weights, 3-5 transparencies, 3-28 types, 3-3 usage guidelines, 3-4 paper release blades cleaning, 5-9 parts of
Index printing basics, 3-2 binding edge options, 3-24 cleaning, 5-2 custom size paper, 3-52 envelopes, 3-34 glossy paper, 3-46 labels, 3-40 Layout tab, 3-20 Output Options tab, 3-20 Paper Quality tab, 3-20 selecting 2-sided, 3-25 selecting individual job printing options Macintosh, 3-22 selecting options, 3-20 selecting preferences, 3-20 side two of pre-printed paper, 3-26 TekColor tab, 3-20 transparencies, 3-28 two-sided pages, 3-24 PrintingScout alerts, 6-19 print-quality modes, 4-2 problems solving, 4-5
Index Tray 1 loading paper, 3-8 printing custom size paper, 3-53 printing envelopes, 3-35 printing glossy paper, 3-47 printing labels, 3-41 printing transparencies, 3-29 trays additional, 1-5 Trays 2-4 loading paper, 3-14 printing glossy paper, 3-49 printing transparencies, 3-30, 3-43 supported paper, 3-7 troubleshooting infoSMART, 1-10 paper jams, 6-2 PhaserSMART, 1-10 predominate light stripes, 4-7 print-quality, 4-5 random light stripes, 4-6 smudges or smears, 4-5 Technical Support, 1-10 transparency ima
