Software Version 10.
©2009 Xerox Corporation. All rights reserved. Xerox® and the sphere of connectivity design, Xerox Nuvera® and FreeFlow® are trademarks of Xerox Corporation in the United States and/or other countries. Changes are periodically made to this document. Technical inaccuracies and typographic errors will be corrected in subsequent editions. Document Version: 10.01 (November 4 2009).
Table of Contents Preface....................................................................................................................... v General Purpose and Audience .......................................................................................................v 1 2 3 Software Versions....................................................................................1-1 New Capabilities in Version 10.0 Software....................................2-1 Release Issues ......................
Preface General Purpose and Audience This document for the Xerox Nuvera contains the following information: • Software release deliverables and version numbers • New features in this release • Issues resolved in this release • New issues present in this release • Known operating limitations that are to be resolved in a future release Standard system operating procedures and information can be found in the following documentation: • For specific information about system operations, performance and
Preface Xerox Nuvera [This page left intentionally blank] vi Hints and Tips Guide
1 Software Versions 1 This document references the following software versions: Item Version Number Free Flow Print Server 7.0 SP3 / Tigris System software RV.10.0.27.04 IPDS (must match DocuSP version) CP. 7393.43 FreeFlow Print Server 7.0 SP3 Remote Workflow * CP.7393.43 (English) FreeFlow Print Server 7.0 SP3 and Variable Input version FreeFlow Print Server 7.0 SP1 Includes Variable Input (VI) and Variable Print Manager (VPM) version 5.0.
2 New Capabilities in Version 10.0 Software 2 The following is a list of new capabilities enabled with version 10.0 software: • Availability of the new Xerox Nuvera 200/288 MX Perfecting Production System configurations. These are dual engine configurations, similar to the Xerox Nuvera® 200/288 EA Perfecting Production System, but with support for MICR printing.
3 Release Issues 3 Issues resolved The following is a list of Nuvera 9.1 issues that have been resolved and no longer apply to Xerox Nuvera 10.
Release Issues Xerox Nuvera New issues in this release for DS3500 CQ#46637 “Close top cover” status does not consistently disappear after closing the top cover Description The Stacker Module “Close Top Cover” status message is not alwaysgoing away when you close the top cover due to possible stray sheets in area 1-6. Workaround If the Stacker Module “Close Top Cover” status message is not going away when you close the top cover, then please check Areas 1-6 for any stray sheets and remove them.
Xerox Nuvera Release Issues Issues remaining from previous release CQ#43933 Unable to Eject CD Tray Description Customer is unable to eject CD tray from GUI or CD-ROM button and unable to read CD. This stops working after the first successful eject. Workaround 1. 2. 3. 4. 5. Insert Media in Tray using "Hard Button" in the CD Tray. If the Pop-Up Menu doesn't show up, go to Print from File Button and select "Browse". Press "Re-display" to show the pop-up menu.
Release Issues Xerox Nuvera Workaround Recommend using inserts less than 90gsm when body is 60gsm. CQ#43522 Annotation-1 Description Do not use Annotation when feeding from the short edge feed tray and selecting the 180 rotate. The annotation will be upside-down. Workaround None. CQ#43522 Annotation-2 Description When performing a “Copy and Save” or “Print and Save” operation with annotations turned on, the reprint of the saved job will be unreadable.
Xerox Nuvera Release Issues CQ#44186 Recognizing Indication of Successfully Proofed Job Description When a job is successfully proofed, there appears to be no indication that it has been proofed. Workaround Ensure the “Proof/Review Status” column is in the visible portion of the table. This column is identified by a computer icon in the header. If the column is at the end of the table (left side), move it to the beginning (right side).
Release Issues Xerox Nuvera CQ#43933 Unable to Eject or Read CD From GUI or CD Button Description Operator cannot read the CD or cannot eject the CD tray from either the GUI or the CDROM button. May occur after the first successful eject. The popup menu for the CDROM is not displayed. Workaround Take the following steps: 1. 2. 3. 4. 5. 6. 7. Click on the “Print From File” Button and select “Browse” Select CD in the “Look In” drop down. Press the “Re-Display” button above the “Look In” area.
