Mobile DVR Model:LZE500 User Manual www.xmlenz.com Xiamen Lenz Communication Co.
Table of Contents Warning ........................................................................................................................................................... 3 DECLARATION OF CONFORMITY .......................................................................................................... 4 Chapter 1 Product Introduction ................................................................................................................... 6 1.1 About E500 .............................
Warning This equipment complies with CE radiation exposure limits set forth for anuncontrolled environment. This eq uipment should be installed and operated withminimum distance 20cm between the radiator & your body.
DECLARATION OF CONFORMITY Applier certifies that the following designated product Product Name: Mobile DVR Model No.: LZE500 Is in conformity with the standard(s) EN60950-1：2006+A11:2009+A1:2010+A12:2011+A2:2013 EN62311:2008 Draft ETSI EN301489-1 V2.2.1 Draft ETSI EN 301 489-17 V3.2.0 Draft ETSI EN301489-19 V2.1.0 Draft ETSI EN301489-52 V1.1.0 EN303 413 V1.1.1 EN301908-1 V11.1.1 EN301908-13 V11.1.2 EN300 328V2.1.1 EN301 893V2.1.1 EN300 440V2.1.
The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.
Chapter 1 Product Introduction 1.1 About E500 LZE500 Mobile DVR is a compact, full-featured recording system that uses SD card, hard disk (HDD) and solid state disk (SSD) as the storage device. It provides H.264 high-quality and max 8 channels of 720P/1080P AHD recording, and 8 channels of 720P/1080P high definition video surveillance and fleet management for police car, ambulance, fire engine, public buses, tourist buses, etc.
1.4 Front Panel No. Item Interface 1 LCD LCD 2 Button Button 3 WORK Red LED GPS Green LED HDD1 Green LED HDD2 Green LED MIRROR Green LED SD Green LED IPC1 Green LED Function For Display “MANU”，“▲”，“▼”，“OK” Indicates the device power-on and wireless network connection status; Fast flash: device registration network Slow flash: The device is registered on the network.
IPC2 Green LED 4 USB USB Interface 5 debug Debugging 6 IC Card Contact IC card 7 SIM 8 SD 9 Hard disk Box 10 Hard disk lock 11 RS232 With drawer type card holder Self-elastic SD card holder Hard disk Box Flashing: IPC Ethernet has data transmission and reception IPC2 indicator; Light off: IPC is not connected Light on: IPC Ethernet is connected Flashing: IPC Ethernet has data transmission and reception Local upgrade CPU serial port print information, Can be used for upgrade Driver iden
4 POWER M16 5P Power Input 5 MIRROR M12 5P Black Box 6 PANEL M16 10P 7 IPC1-2 12 PIN interface 2 channels IPC access 8 AHD1-8 32 PIN interface 8-channel AHD camera access 9 RS232 6 PIN interface Serious port 10 EXT.IO 30 PIN interface RS232 interface, RS485 interface, CAN Bus interface, High and low level detection, speed detection etc 11 SPEAKER 4PIN interface Driver console power support and communicating， Speaker access，microphone access，CVBS video output Audio out 1.
POWER SUPPLY OTHERS Network 1-CH RJ45 Ethernet converter interface USB 1-CH USB, type A Input Power DC 9V ~ 36V, typical 12V/24V Power Output-1 +5V@2A Power Output-2 8CH +12V@500mA (analog cameras) Power Output-3 2CH +12V@500mA (IP cameras) Power Consumptions <25W (not connect with accessories and HDD/SSD) Operating Temperature -20ºC~+70ºC Size 188mm(L) *188mm(W)*112mm(H) Weight 2.4kg Certification CE, RoHS, CCC Chapter 2 Installation 2.
Please use a 2.5-inch hard drive and purchase it from a regular store to ensure the quality of the hard drive. After the hard disk is installed, you need to format it before you can record it, otherwise the system will judge the hard disk error.
/ 19
/ 19
2.3 Wiring Diagram 2.4 Interface 2.4.1 4G Antenna The interface standard of the antenna port is SMA male External Antenna Antenna gain: 3.
2.4.2 GPS Antenna The GPS antenna adopts the standard SMA interface. The curved side of the GPS antenna is facing upwards, and the flat side is facing downward. The fixed position must make the arc of the antenna face the sky, and there should be no obstruction on the upper side. The metal-covered explosion-proof membrane will affect the reception of the satellite signal, and the explosion-proof membrane at this position should be avoided or dug; External Antenna Antenna gain: 3.
2.4.4 Power The following picture shows the 5-pin power cable, 5-pin connector to connect the device power interface, bare wire part: the red wire is connected to the positive pole, the black wire is grounded, and the yellow wire is connected to the ACC (required) 2.4.5 10-PIN Console Can transfer speakers, microphone, Driver console; 2.4.
2.4.7 SIM Card Installation To purchase a SIM/UIM card from a telecom carrier, the card must be opened for data services; if voice calls are required, voice services must be activated. Remove the SIM card slot and insert the SIM/UIM card as shown below. Note that the side of the chip is facing down. Step 1 Step 2 Step 3 Step 4 The side of the chip is facing down.
2.5 Definition of PINs Pins on the device Definition Remark 1. Power + 2. Power + 3. ACC 4.GND 5.GND Connect power input, ACC signal input 1. DC 5V 2. USB3. USB+ 4. GND 5. MIRROR access detection 1.DC 5V 2.RS232_RXD2 3.RS232_TXD2 4.MICP 5.MICN 6.SpeakerP 7.SpeakerN 8.GND 9.Video OUT 10.GND Connect the Driver console, speaker, microphone, 1. IPC2_TX+ 2. IPC2_RX+ 3. GND 4. 12V IPC1 5. IPC1_RX6. IPC1_TX- 7. IPC2_TX8. IPC2_RX9. 12V IPC2 10. GND 11. IPC1_RX+ 12. IPC1_TX+ 1.12V camera8 power 2.
9.12Vcamera 4 power 10.Camera 4 11.12Vcamera 3 power 12.Camera 3 13.12Vcamera 2 power 14.Camera 2 15.12Vcamera 1 power 16.Camera 1 1.Reserved 2.Reserved 3.GND 4.232_TX 5.232_RX 6.GND 25.GND 26.Audio 4 27.GND 28.Audio 3 29.GND 30.Audio 2 31.GND 32.Audio 1 1. Debug_TX 2. GND 3. RS232-2-TX 4. A RS485+ 5. B RS485+ 6. GPS-TX 7. Door sensor 8. CANH1 9. CANH2 10. Brake 11. Right turn 12. Low beam 13. Panic button 14. Oil circuit control 15. GND 16. Debug_RX 17. GND 18. RS232-2-RX 19. A RS48520. B RS48521.
FCC Caution. (1)§ 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.
