Mobile Thermal Printer RPP02N USER MANUAL
Xiamen Rongta Technology Co., Ltd. Contents I. Notice ..................................................................................................................................2 1.1 Safety Notice .................................................................................................................2 1.2 Usage Notice .................................................................................................................2 1.3 Storage Notice .........................................
Xiamen Rongta Technology Co., Ltd. I. Notice Please read the following information carefully before using the printer! 1.1 Safety Notice This printer can only use battery and power adapter provided by our company, or it may cause damage to the printer, battery leakage, fire or explosion. Do not put the battery into the fire, not make it short circuit, break up or heating, otherwise it may cause the battery leakage, fire or explosion.
Xiamen Rongta Technology Co., Ltd. Higher humidity (>/=85%) or lower humidity (
Xiamen Rongta Technology Co., Ltd. 2. Do not use or place the battery near burner or high temperature environment. Overheating may cause the damage to the resin shell and/or heat insulation material, and bring the short circuit in the battery then lead the overheating, burning and/ or explosion of it. 3. Please use dedicated charger when charging.
Xiamen Rongta Technology Co., Ltd. unusual chemistry reaction, then may lead to overheating, burning and/or explosion of it. II. Introduction 2.1 Printer outer design 5 2 3 2 6 1 4 7 9 8 11 1. Feed Key 10 2. Power Key 3. Status Indicator 4. Charge Indicator 5. Printer Top Cover 6. Body 7. Printer front Cover 8. RS232 Socket 9. Power supply Interface www.rongtatech.
Xiamen Rongta Technology Co., Ltd. 10. USB Interface 11. Battery Cover 2.2 Accessories Standard Accessories Battery Power Charger Paper Roll CD-ROM Serial Data Wire USB Data Wire Optional Accessories Leather Sheath www.rongtatech.
Xiamen Rongta Technology Co., Ltd. III. Performance 3.1 Print Performance Printing way: Direct thermal print Paper width: 56mm Printing width: 48mm Resolution: 8dots/mm (203dpi) Dot/line: 384dots Printing speed: 50-80mm/s Paper thickness: 60-80μm Printing Content: Chinese (Support all GB18030 Chinese character, character sets), ASCII character, some full width custom characters and some half width custom characters; barcode: CODE39, EAN13, EAN8, CODABAR, CODE93, ITF; graphics. 3.
Xiamen Rongta Technology Co., Ltd. Power: 1400 mAH rechargeable li-ion battery Adapter to recharge: battery can be filled with in 3 hours. USB to recharge: battery can be filled with in 6 hours. Notice: The battery to recharge can’t use Adapter and USB at the same time. A charging time available: Normally, the battery could be used for printing 100meters or 3 hours.
Xiamen Rongta Technology Co., Ltd. Press here to open the cover Usage Method: 1. Using two hands to keep pressing the cover then open it. 2. As shown in picture, please put the paper roll in and do not put it in wrong direction, otherwise it would lead the printer unable to work. 3. As shown in picture, pull out part of paper; please make sure to pull the paper out of the paper roll compartment. 4. Put the paper roll in the right way and then close the cover. 4.2 Basic Function 4.2.
Xiamen Rongta Technology Co., Ltd. printer will print out the self-test page, which contains the printer status, setting and printing sample. 4.2.4 Feed (Feed Manually) Under printer working status, press "FEED" key, the printer will start feeding paper for 250mm length. If the paper has black mark accepted by the printer, the printer will stop feeding when goes to the black mark. If feeding length is set as "0", printer feeding will not be affected by black mark. 4.2.
Xiamen Rongta Technology Co., Ltd. 1. Power on Printer 2. Primary Device search for external Bluetooth devices 3. If there are more than one external Bluetooth devices, select the printer which is corresponding to the BDA address (refer to self-test page). 4. Input password"0000" 5. Finishing Matching. About matching method details, please refer to primary Bluetooth function description. During matching, RPP02N/BL portable mini printer must be power on.
Xiamen Rongta Technology Co., Ltd. Slow flashing Long lighting No flash Slow flashing Off Off Long Lighting Slow Flashing Low level Finish charging Power on Status Lack of paper No flash Sow Flashing Sleep status With a buzz Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.