Instruction Manual 2.
CONTENTS General Safety Instructions 4 Remote Control 7 Product Overview 9 Controls and Connections 10 First Time Setup 11 General Operations 12 Pairing your soundbar 13 Troubleshooting 14 Specifications 15 Specifications Last Page
GENERAL SAFETY INSTRUCTIONS Read this manual thoroughly before you start using the Soundbar. Store this manual, the completed warranty card, your receipt and the product packaging. The safety precautions instructions reduces the risk of fire, electric shock and injury when correctly complied to. Please follow all instructions and take notice of all warnings. IMPORTANT INFORMATION • Only using furniture that can safely support the Products.
GENERAL SAFETY INSTRUCTIONS (Cont.) Please follow instruction when installing this product in accordance with the instruction manual. This product must be positioned in a sufficiently stable location, it can be potentially hazardous due to falling when mounted and can cause injury, particularly to children if it positioned incorrectly.
GENERAL SAFETY INSTRUCTIONS (Cont.) • If you notice any unusual odors or smoke around the unit, immediately disconnect the unit from the outlet and contact the service center. Failure to do so may result in fire or electric shock. • When not using the unit for long periods of time or when you are moving the unit please ensure to disconnect the power supply from the wall socket.
REMOTE CONTROL • The remote control has a reception range of approximately 5m. Be sure to point the remote control directly at the sensor at the front of the soundbar. • Make sure there are no obstacles in the way. This will intefere with the sensor strength. • Handle the remote control carefully, please do not drop, apply shock or step on it. • Do not spill water on it.
REMOTE CONTROL (Cont.) CAUTION! Battery Precautions • Do not use other batteries other than the one specified in this manual. • Danger of explosion if incorrectly replaced by a battery other than the one specified. • Do not store battery with other metallic objects, doing so can cause the battery to short-circuit, leak or explode. • Ensure the battery is not exposed to excessive heat, direct sunlight or fire. • Do not try to short-circuit, disassemble or throw the battery into a fire.
PRODUCT OVERVIEW 1 2 3 5 1: SOURCE: 4 6 7 8 9 SHORT PRESS TO POWER ON WHEN OFF, AFTER POWER ON SHORT PRESS FOR FUNCTION CHANGE, LONG PRESS TO TURN OFF. 2: VOL-: SHORT OR LONG PRESS FOR VOLUME DOWN; 3: VOL+: SHORT OR LONG PRESS FOR VOLUME UP; 4: PAIR: SHORT OR LONG PRESS BLUETOOTH PAIR; 5: DC IN 6: USB PORT 7: AUX IN (3.
CONTROLS AND CONNECTIONS HDMI Connect a HDMI cable (not supplied) from your TV HDMI/ARC port to the HDMI socket on the soundbar. Then change the mode on your soundbar to HDMI Mode. Note: To enable the Audio Return Channel (ARC) feature, the HDMI must be connected to an ARC enabled HDMI on your TV. (go to next page for details on ARC). OPTICAL Remove protective cap from the Optical socket on the soundbar and plug in the optical cable (not supplied) from your Soundbar to the TV optical port.
CONTROLS AND CONNECTIONS (Cont.) AUDIO RETURN CHANNEL (ARC) / HDMI ARC function is used for connecting the Soundbar to the TV with a HDMI cable through an audio return channel. This means you can listen to the TV sounds through your Soundbar via HDMI cable. To enjoy the HDMI ARC Mode 1. Make sure the Soundbar is connected to the TV HDMI(ARC) port. 2. Ensure the Soundbar is set to HDMI Mode 3.
GENERAL OPERATION During On mode, press “M” on the Remote Control repeatedly to select between AUX, BT (Bluetooth ®), OPTICAL, HDMI (ARC) modes. Operate your audio device directly for playback features. Turning on/off the unit 1. Insert the output cable from the DC adaptor into power socket on the rear of the Sound Bar. 2. Connect to DC mains plug into socket outlet properly. 3. Press the power button on the right side panel of Sound Bar or top of remote control to power on the unit. 4.
PAIRING YOUR SOUNDBAR Pairing with a Bluetooth Enabled Device: Before you play music from your Bluetooth device, it needs to be paired with the Soundbar. 1. Once powered, press the button on the Side of soundbar or MODE to enter BT mode on the RC to activate pairing mode. 2. Now that the unit has entered pairing mode, on your smart device, select to search for devices. 3. Select “BSB201S” in the list of devices that appear. “BT” will stay lit steadily on the screen once there is a successful connection. 4.
TROUBLESHOOTING Never try to repair the soundbar yourself. If you encounter any problems when using this unit, check the following points before seeking for service. Problem Solution No Power • Ensure that the Switching Adaptor is connected to power socket outlet. • Ensure that there is power at the DC outlet. • Press standby button to turn the unit on. Remote control does not work • Before you press any SOURCE button, first select the correct source.
SPECIFICATIONS Power Supply 20VDC 1.8A Frequency Response Soundbar: 50Hz to 15kHz Bluetooth 5.0, A2DP, AVRCP Bluetooth Range Up to 10m Dimensions Soundbar: 940 (w) x 95 (d) x 70 (h) mm Weights Soundbar: 2.26 kg The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Ayonz Pty Ltd is under license. Other trademarks and trade names are those of their respective owners.
CUSTOMER HELPLINE: info@ayonz.
