BT-129 Product Information Guide
Specifications Bluetooth Compliance Bluetooth V 4.0 Frequency Band 2.4~2.4835GHz ISM Spectrum Modulation GFSK (Gaussian Frequency Shift Keying) Operating Range Up to 10m (indoor) Battery Capacity 3.7V, 2200mAh Power Supply 5V, 0.5A Charging Time About 3 hours Standby Time About 120 hours Compatibility Mobile phone/device supporting Bluetooth V1.
Congratulations Troubleshooting Thanks for purchasing the wireless speaker BT-129. Enjoy this smart product, please read below instructions carefully. It's more than just a Bluetooth Speaker! Volume is not high enough Care and Maintenance 1. Do not attempt to service the product yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please contact your local reseller before you send the product for repair. 2.
Contents LED Indicator Speaker Status LED Status Congratulations Power On Blue LED flash . Care and Maintenance 1 Power Off Red LED stay on for a while and get off. Feature List Layout 3 Pairing Red LED and Blue LED flash alternately. Use Instrution 6 Pairing Succeed Blue LED flashes 4 times along with two beeps. Battery/Charger 7 Operations Standby Blue LED flashes once every 8 seconds. LED Indicator 8 13 Disconnected Red LED and blue LED flash simultaneously.
Features List Music Playing 1. Clear and crystal sound , superior stereo performance 2. Build-in microphone 3. Loud , clear , deep bass and stable 4. Wrapped by TPU replaceable and colorful skin 5. Waterproof(IPX7), Shockproof and Scratchproof 6. Bluetooth connection (Bluetooth V4.0) 7. Music playing control 8. Voice dialing 9. Bluetooth stereo (A2DP/AVRCP) 10. Low battery clarm ( Alarm and LED indicator) 11. LED indicator (Low battery/Charging/full charging) 12.
Layout Voice Dialing In standby mode, short press and then you will hear a tone for voice dialing. at the same time Front View LED Light Microphone Note: This function need the support of the mobile phone. Mute/Un-mute Press and at the same time during a call to mute the microphone. A single beep will follow to indicate success of the operation. Loudspeaker Loudspeaker Note: There will be two beeps every 5 seconds until you hold these two buttons again to un-mute the microphone.
Calling Top View Answer a call Short press to answer an incoming call. Reject a call Press and hold for 2 seconds to reject the call. End a call Volume- Volume+ Multi-function (MFB) After calling, short press on the phone. to end the call, or end the call Last Number Redial Short press 2 times to redial the last call.
Pairing and connecting Use Instruction Enter pairing mode Function Key Item Press and hold for 7 seconds. Wait until red LED and blue LED flash alternatively along with two beeps. Pair 1.Enable Bluetooth function on your phone or other smart devices and search Bluetooth accessories in range. 2.Choose BT-129 when it shows up and get connected (input 0000, if a pairing code is requested). 3.When blue LED flashes 4 times along with two beeps, BT-129 gets connected successfully.
Battery/Charger Operations The speaker has a built-in Li-ion battery (3.7V, 2200mAh), so it can be used without connecting with a power supply(5V,0.5A). To charge the battery, please connect with computer or charger through charging line. Power On / Off Notes: When BT-129 is charging the LED status indicator will be RED. When fully charged the RED status indicator LED will go off. From fully discharged battery to fully charged will take 3 hours.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.